DOWNLOAD Sharp CD-BA1700 Service Manual ↓ Size: 1.2 MB | Pages: 36 in PDF or view online for FREE

 EON-TI

 

 "PTY TI" and "SELECT" will appear alternately for about

6 seconds.

 The selected "TI" will flash.

 "TI" and "WAITING" will appear for 2 seconds each.

 "TI" will appear, and the unit will enter the EON-TI stand-

by mode.

 If the EON button is pressed when "EON" is not dis-

played, "NO EON" will appear for 5 seconds to indicate
that the unit cannot enter the EON stand-by mode.

Checking the stand-by mode setting:
When in the EON stand-by mode, press the EON button.
("TI"  

"WAITING")

To cancel the EON stand-by mode:
When in the EON stand-by mode, press the EON button.
Within 4 seconds, press it again. The EON stand-by mode
will be cancelled.

 "TI" will go out.

 If neither "TP" nor "TA" appear, then even if "EON"

appears, the unit cannot enter the EON-TI stand-by
mode. In this condition, if the PTY.TI SEARCH button is
pressed after TI is selected, "NO TI" will flash for 4 sec-
onds.

(Main unit operation)

Not lit

Not lit

This programme does not carry traffic announcements nor
does it refer, via EON, to a programme that does.

Not lit

Lit

This programme carries EON information about another pro-
gramme which gives traffic information.

Lit

Not lit

This programme carries traffic announcements but none are
currently on air and may also carry EON information about
other traffic announcements.

Lit

Lit

A traffic announcement is currently on air on this programme.

In the following cases, the EON stand-by mode will be cancelled.

 When the unit is set in the stand-by mode.
 When the unit is switched to another band in the EON stand-by mode.
 When you change the FM station whilst in the EON stand-by mode.
 When a preset call is made.

 During the same programme as the specified PTY (or TA) is being broadcast on the station you are receiving, the unit

will not switch to other network station.

 If there are more than two other network stations you want to listen to, compare the strength of each station's signal and

tune in the station with the strongest signal. (EON-AF) However, if the frequency of other network station has been stored
in the preset channel memory, the unit will switch to that preset channel.

 To cancel the ON (other network) station tuned in by the EON system and to return to the original station, press the EON

button.

 After the unit returns to the original station, the stand-by mode will still be active. (The "TI" or "PTY" will remain lit.)
 The unit will not switch from the ON station to another network station. The unit returns to the original station.
 When the unit switches automatically to "other network" station, "WEAK SIG" will appear and the unit will return to the

original station if there is any problem with this station or the station cannot be received properly.

 Even if the unit switches from the station you are listening to directly to some "other network" station, the unit will search

for the station with the strongest signal and switch to it if the signals from the other network stations are very weak. How-
ever, if the signals from all the other network stations are very weak, or if the tuning conditions are very bad (due to elec-
trical noise), the unit will stop searching, "WEAK SIG" will be displayed, and the unit will return to the original station you
were receiving.

 TAPE 1 or TAPE 2 playback

 

 When playback is performed using the remote control,

press the TAPE 1 or TAPE 2   button.

 
To stop playback:
Press 

the  

(TAPE ) 

button.

Fast forward/rewind: (TAPE 2 only)
1

Press the   (TAPE  ) button, then press the TAPE (1 
2) button to select TAPE 2.

2

To advance the tape, press the 

 button. To rewind it,

press the 

 button.

Caution:
 To remove the cassette tape, press the   (TAPE  ) but-

ton, and then open the cassette compartment.

 Before changing from one tape operation to another,

press 

the  

(TAPE ) 

button.

 If a power failure occurs during tape operation, the tape

head will remain engaged with the tape and the cassette
door will not open. In this case, wait until power is
restored.

TAPE 1

TAPE 2

PUSH

EJECT

PUSH

EJECT

 Recording from the built-in CD player (CD 

 Use the APMS function to store the tracks you want to

record in memory. (See page 14.)

 "SYNC" and "REC" will flash.

 "SYNC" will disappear and "REC" will light up.

 CD playback will start approximately 5 seconds after the

tape starts.

To stop recording:
Press the   (CD  ) button.
The CD and tape will stop.

 When the end of the tape is reached whilst recording, the

CD player will display the track number which was being
played at that time, and stop automatically. If you want to
restart recording from the beginning of the interrupted
track, turn over the tape, press the REC PAUSE (

) but-

ton and then the   /   (TAPE 2  ) button. (If tracks have
been stored in memory using the APMS function, record-
ing will restart from the first track stored in memory.)

 Recording from the built-in radio

 "REC" will flash.

 "REC" will appear.

To interrupt recording:
1

Press the REC PAUSE (

) button.

 "REC" will flash.
2

Press the   /   (TAPE 2  ) button.

 "REC" will appear.

To stop recording:
Press 

the  

(TAPE ) 

button.

 If a whistling noise is heard whilst recording from an AM

station, move the AM loop aerial to a position where
noise is no longer heard from the unit.

 When recording important selections, be sure to make a

preliminary test to ensure that the desired material is be-
ing properly recorded.

 The volume and sound quality can be adjusted with no

effect on the recorded signal (Variable Sound Monitor).

 Metal and CrO  tapes should not be used for recording

or dubbing.

TAPE 2

PUSH

EJECT