Panasonic TY-ST42PT1E / TY-ST42PT1U / TY-ST42PW1E / TY-ST42PW1U / TY-ST42PF1E / TY-ST42PF1U / TY-WK42PV1E / TY-WK42PV1U / TY-WK42PR1E / TY-WK42PR1U Service Manual / Other ▷ View online
5-
1
TY-WK42PR1E
TY-WK42PR1U
Wall-hanging bracket
(angled)
CONTENTS
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-
2
Instruction of the installation . . . . . . . . . . . . 5-
3
1.Fixing the wall-hanging bracket to the wall
. . . . . . . 5-
3
2.Adjusting the angle of the display fitting
. . . . . . . . . 5-
4
3.Fixing the insulating spacers to the display unit
. . . . 5-
5
4.Attaching the display unit to
the wall-hanging bracket
. . . . . . . . . . . . . . . . . 5-
6
Removing the display unit . . . . . . . . . . . . . . . 5-
7
Assembly diagram
5-
2
Description
Installation diagram
89
1030
660
89.5
633.5
(160)
310
100
94
Units : mm
* A clearance of at least 100mm at the top of the display unit should be provided.
** Installation of the wall-hanging bracket requires a depth of 310 mm.
*
**
5-
3
Instruction of the installation
Fixing the wall-hanging bracket to the wall
1
Check the strength of the installation location
The wall-handing bracket weighs approximately 6kg, and the wide plasma
display unit by itself weighs 33kg. Refer to the wall-hanging bracket installa-
tion dimensions in the diagram below to check the strength of the wall in six
installation locations, and add reinforcement if any of these locations are not
strong enough.
Further installation of the wall-hanging bracket requires a depth of 310 mm.
1) Select an installation site with an area of at least 1,500 mm wide by
800 mm high. Referring to the figure, make a positioning mark for
the location of the center-top hole;
the location of the center-top hole;
2) Measure and mark the locations 450 mm to the left and 450 mm hor-
izontally to the right of the location you marked in 1);
3) Measure and mark the locations 450 mm below each of the marked
location.
2
Insert and fasten a M6 screw bolt into the center-top hole.
The wall-hanging bracket
has installation holes
provided at 14 locations.
has installation holes
provided at 14 locations.
If the wall material does
not allow sufficient
strength by using six
installation holes, use
some of the spare holes.
However, depending on
the construction material
at used at the place of
installation, cracks may
develop if screws are
inserted too close to
each other.
not allow sufficient
strength by using six
installation holes, use
some of the spare holes.
However, depending on
the construction material
at used at the place of
installation, cracks may
develop if screws are
inserted too close to
each other.
450
15
450
15
930
490
450
20
20
Wall installation holes(6 locations)
Used for routing wires behind a wall
Units : mm
If required, use
commercially available
M6 bolts which suit the
wall materials.
commercially available
M6 bolts which suit the
wall materials.
5-
4
3
Use a level gauge to correct the alignment of the wall-hanging bracket,
and screw bolts into the remaining five holes.
and screw bolts into the remaining five holes.
4
Provisionally tighten the fixing screws.
After determining the positions and checking them against the bracket,
embed M6 bolts or nuts. Furthermore, when embedding the bolts, ensure
that the bolts protrude from the wall by 10 to 15 mm.
Adjusting the angle of the display fitting
The angle of the display fitting can be adjusted to one of the five positions
ranging from vertical to 20 tilt in 5 steps.
At the time of shipment, the angle of tilt is set to 5 from vertical. To change
this angle, adjust the position of the stay.
If the screws protrude
more than 5 mm, it will
not be possible to install
the Wide Plasma Display
in the correct position.
more than 5 mm, it will
not be possible to install
the Wide Plasma Display
in the correct position.
The stay is not needed if
the display unit is to be
fixed vertically.
the display unit is to be
fixed vertically.
Angle adjustment positions
5
10
15
20
0
5tilt
10tilt
10tilt
15tilt
20tilt
No tilt
No tilt
5 tilt
No tilt
15 tilt
stay
Click on the first or last page to see other TY-ST42PT1E / TY-ST42PT1U / TY-ST42PW1E / TY-ST42PW1U / TY-ST42PF1E / TY-ST42PF1U / TY-WK42PV1E / TY-WK42PV1U / TY-WK42PR1E / TY-WK42PR1U service manuals if exist.