Panasonic TY-ST42PT1E / TY-ST42PT1U / TY-ST42PW1E / TY-ST42PW1U / TY-ST42PF1E / TY-ST42PF1U / TY-WK42PV1E / TY-WK42PV1U / TY-WK42PR1E / TY-WK42PR1U Service Manual / Other ▷ View online
2-
1
Wall stand
TY-ST42PW1E
TY-ST42PW1U
CONTENTS
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-
2
Instruction of the installation . . . . . . . . . . . . 2-
3
1.Assembling the wall stand
. . . . . . . . . . . . . . . . . . 2-
3
2.Fixing the insulating spacers to the display unit
. . . . 2-
4
3.Attaching the wall stand to the display unit
. . . . . . . 2-
6
4.Fixing the display unit to the wall
. . . . . . . . . . . . . . 2-
7
Removing the display unit . . . . . . . . . . . . . . . 2-
8
Assembly diagram
2-
2
Description
Installation diagram
89
19
1030
633.5
100
1140
506.5
123.5
110
143.5
Units : mm
* A clearance of at least 100mm at the top of the display unit should be provided.
*
2-
3
Instruction of the installation
Assembling the wall stand
1
Check the strength of the installation location.
The height measurements marked ** are particularly important. Do not
attempt to set up the pedestal in a location where these dimensions and a
clearance of at least 100 mm at the top of the display unit should be pro-
vided.
1) On the wall, measure and mark a height 650 mm above the floor;
2) Measure and mark the location 475 mm horizontally to the right of
the mark you made in 1). Measure and mark points 180 mm and 360
mm above each mark (for a total of six marked locations);
mm above each mark (for a total of six marked locations);
3) Drill a hole at each of the six marked locations on the wall.
Refer to the holding
bracket installation
measurements in the
drawing left.Ensure that
the wall is able to bear
the weight at each of the
4 upper and lower
installation locations.
Add reinforcement if any
of these locations are
not strong enough.
bracket installation
measurements in the
drawing left.Ensure that
the wall is able to bear
the weight at each of the
4 upper and lower
installation locations.
Add reinforcement if any
of these locations are
not strong enough.
Ensure an area of at least
650 mm by 1,230 mm in
length at the location
where you plan to install
the holding bracket.
650 mm by 1,230 mm in
length at the location
where you plan to install
the holding bracket.
The holding bracket has
6 slits through which the
bracket can be fixed to a
wall with screws.
6 slits through which the
bracket can be fixed to a
wall with screws.
If the wall material does
not allow sufficient
strength by using six
installation holes, use
some of the spare holes.
However, depending on
the construction material
used at the place of
installation, cracks may
develop if the screws are
inserted too close to
each other.
not allow sufficient
strength by using six
installation holes, use
some of the spare holes.
However, depending on
the construction material
used at the place of
installation, cracks may
develop if the screws are
inserted too close to
each other.
744
560
390
180
180
650
630
400
Units : mm
Wall installation holes
Spare wall installation holes (2 locations)
**
**
(4 locations)
floor surface
2-
4
2
Fix a M6 screw, through any of the slits in the bracket, into the corre-
sponding hole in the wall.
sponding hole in the wall.
Using a level along the top or bottom edge, ensure that holding bracket is
horizontal.
3
Fix the screws through the slits into the remaining three holes.
4
Provisionally tighten the fixing screws.
Fixing the insulating spacers to the display
unit
unit
1
1) Spread a clean cloth over a level floor or base, and place it on the
display unit face down.
2) Remove the screws and covers.
Keep them in a safe place for possible future use.
The holding bracket must always be installed. It prevents the display unit from
falling after installation.
If the screws protrude
more than 5 mm, it will
not be possible to
properly install the
display unit.
more than 5 mm, it will
not be possible to
properly install the
display unit.
Carefully place the Wide
Plasma Display face
down on top of a clean
cloth, which has been
spread over a flat
surface with no other
objects on it, and then
proceed to the next
step.
Plasma Display face
down on top of a clean
cloth, which has been
spread over a flat
surface with no other
objects on it, and then
proceed to the next
step.
Click on the first or last page to see other TY-ST42PT1E / TY-ST42PT1U / TY-ST42PW1E / TY-ST42PW1U / TY-ST42PF1E / TY-ST42PF1U / TY-WK42PV1E / TY-WK42PV1U / TY-WK42PR1E / TY-WK42PR1U service manuals if exist.