Panasonic TX-51P950M / TX-51P950X / TX-43P950M / TX-43P950X Service Manual ▷ View online
3.5. Cabinet (Top)
1. Remove (12) Screws.
3.6. Speaker (Top Cabinet)
3.7. Screen
1. Remove (20) nails, and remove (2) Screen Holders (vertical
side) and (4) Screen Holders (horizontal side).
9
TX-51P950M / TX-51P950X / TX-43P950M / TX-43P950X
3.8. Mirror
1. Remove (3) screws.
3.9. Rear Cover (Top)
1. Remove the Top Cabinet.
2. Remove (2) screws.
2. Remove (2) screws.
3.10. Rear Cover (Bottom)
1. Remove (15) screws.
2. Remove (1) screw.
2. Remove (1) screw.
10
TX-51P950M / TX-51P950X / TX-43P950M / TX-43P950X
3.11. Disassembly For CRT Removal
To facilitate CRT replacement, the complete CRT mounting
chassis does not need to be removed.
1. Remove the Screen Frame Ass´y, Decorative Panel and
chassis does not need to be removed.
1. Remove the Screen Frame Ass´y, Decorative Panel and
the Bottom Rear Cover Ass´y. ( See Disassemble for
Service ).
Service ).
2. Unplug the defective CRT Dag ( GND ), from the CRT
Board, LBGND for LB, LGGND for LG, LRGND for LR.
3. Remove lead wires ( DY, VM coil ) and anode lead wire
from holders as necessary.
4. Remove the CRT Board from the defective CRT neck.
5. Note position of yoke with centering tabs and remove from
defective CRT.
6. From the Top, remove (2) screws from the defective CRT.
7. Release CRT anode lead from CRT chassis wire clamp and
all other wires from holders.
8. Wire the anode lead wire.
9. Lift out CRT assembly with lens assembly and other CRT
9. Lift out CRT assembly with lens assembly and other CRT
neck assemblies.
10. Lay CRT face down on a soft cloth.
11. Remove CRT lens by removing (4) screws.
11. Remove CRT lens by removing (4) screws.
12. Install yoke and VM coil with other CRT neck assemblies on
CRT neck in the same order and position as removed from
the defective CRT.
the defective CRT.
13. Push yoke against bell of CRT and tighten the clamp just
snug enough so it will not easily shift.
14. Assemble CRT focus lens assembly to new CRT with (4)
screws. Make sure focus lens adjustment nut is in the same
location as on other CRT focus lens.
location as on other CRT focus lens.
Note:
Please assemble with screws in the order shown in detail
and tighten with same torque.
and tighten with same torque.
11
TX-51P950M / TX-51P950X / TX-43P950M / TX-43P950X
4.1. Service position for Main
chassis
1. Remove the Rear Cover (Bottom) by removing (15) screws
and (1) screws around its perimeter.
2. Remove lead wires and bundles from holders as necessary.
3. Pull out main chassis and stand it.
3. Pull out main chassis and stand it.
4.2. Service Position for DG-Board
1. Remove the each circuit board from A or D-Board.
2. Connect extension cables between individual circuit board
2. Connect extension cables between individual circuit board
and A or D-Board.
Note:
Extension cable kit is supplied as service fixtures and tools.
PART No. :GP11(N)-1
PART No. :GP11(N)-2
PART No. :GP11(N)-3
4.3. Service Position for K-Board
1. Remove the Speaker Grille.
2. Remove the K-Board by (4) screws.
2. Remove the K-Board by (4) screws.
4 Service Hints
12
TX-51P950M / TX-51P950X / TX-43P950M / TX-43P950X
Click on the first or last page to see other TX-51P950M / TX-51P950X / TX-43P950M / TX-43P950X service manuals if exist.