DOWNLOAD Panasonic KX-TGJ310RU / KX-TGJ312RU / KX-TGJ320RU / KX-TGJ322RU / KX-TGJA30RU Service Manual ↓ Size: 8.52 MB | Pages: 96 in PDF or view online for FREE

57

First, operate the PC setting according to The Setting Method of JIG (Handset) (P.53).
Then download the appropriate data according to the following procedures.

(*2) WW: country code, XXX_YYY: revision number
“XXX_YYY” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting
Method of JIG (Handset) (P.53).

Items

How to download/Required adjustment

FLASH(IC4)

Adjusted parameter data is 
stored in memory. 
(country version batch file, 
default batch file,ect)

1) Please be sure to execute the following steps if you have replaced the FLASH 
IC(IC4).

1. Update BBIC. Refer  How to update the BBIC..
2. Detach the JIG cable, then disconnect the battery.
3. Insert battery.
4. Connect the JIG cable again, and execute the command "getchk", then con-

firm the checksum value is correct.

• If the downloading failes, start again from step 1.

5. Check DECT ID written on Plastic bag of FLASH (IC4).
6. Execute the command "idw xx xx xx xx xx". xx xx xx xx xx: use DECT ID in 

Step 5.

7. Execute the command "epw 00 01 01 CC".
8. Default bath file: Execute the command "default.bat"
9. Common batch file: Execute the command 

"TGJA30_RU_DEF_RevXXX_YYY.bat"(*2).

10. Country version batch file: Execute the command 

"TGJA30_RU_WW_RevXXX_YYY.bat" (*2). 

11. Confirm DECT ID written in the label pated plastic bag of FLASH rom.

12. Write ID(PFPI):  Write DECT ID.

• Execute the command "IDWRITE". Refer to 11.2.3 Commands (P.51)

2) Clock adjustment.
3) Battery low confirmation as below.

Battery Low Confirmation

-

1) Apply 2.40 V between BATT+ and BATT-.
2) Confirm that there is no flashing of Battery lcon.
3) Apply 2.25 V ± 0.08 V between BATT+ and BATT-.
4) Confirm that there is flashing of Battery lcon.
    If need to adjust Battery low detection, please proceed as below.
5) Apply 2.25V between BATT+ and BATT-
    Execute the command
    sendchar PAD
    sendchar LED 0    
    sendchar CRX 0 1    
    sendchar AD1    
    It assumes that the return value is XX*.
    a) 6c   XX   71: No need to adjust
    b) XX: 6A ~ 6B: Need to adjust
    Execute the command
    wreeprom 00 09 01 XX
    wreeprom 00 0A 01 ZZ
    ZZ = XX-1D (hex)
    Note:
    * : If XX is “00” to “69” or “75” to “FF” it may not be able to adjust properly.
        Please check power circuit.

Clock Adjustment (X1)

CLK

1) Apply 2.6 V between BATT+ and BATT- with DC power.
2) Input Command “sendchar sfr“, then you can confirm the current value.
3) Check X’tal Frequency. (10.368 MHz ± 100 Hz).
4) If the frequency is not 10.368 MHz ± 100 Hz, adjust the frequency of CLK 
execute in the command “sendchar sfr xx xx (where xx is the value)“ so that the 
reading of the frequency counter is 10.368000 MHz ± 5 Hz.

58

• Execute COM communicator.exe

1. Initialize COM port.(Only once at first.)

Select “Setting” 

→ “Serial port” → “Initial settings” → “OK”.

2.Select serial port COM number.

Select “Setting” 

→ “Serial port” → “Setting” → “OK”.

Fill up the “COM Options” 

→ “OK”.

Once download is successful for a PC, this step is unnecessary next time to the PC.

• Execute COM communicator.exe again <<Write program>>

1. Select “Addon” 

→ “ProgramLoader”.

Setting

Serial port

Initial settings

OK

Cancel

(1)

(2)

(3)

Setting

Serial port

Setting

OK

Cancel

59

2. Select "Setting" 

→ "Config".

Fill up the “ConfigSettings”.

(2) Select Baud Rate as 57600. If write error happens, select slower Baud Rate (example: 19200).

3. Select download file.

(1)

(2)

(3)

(1)

(2)

60

4. Start download.

(1). Connect Unit and 3wire jig.
(2). Confirm "Turn on power to target and press download." display.
(3). Power off the unit, then power on.
(4). Press "Download" button again.

5. Finish download.

Completed dialog means "Download finished successfully!." It takes more than 20 minutes to download

       ( It depends on baud rate). If error message is displayed, proceed from step 3 again.

6. Continuous download.

Write next unit's software with proceeding from step 3 to Step 5.

(2)

(4)