Panasonic KX-TGJ310RU / KX-TGJ312RU / KX-TGJ320RU / KX-TGJ322RU / KX-TGJA30RU Service Manual ▷ View online
41
KX-TGJ310/KX-TGJ312/KX-TGJ320/KX-TGJ322/KX-TGJA30
9.3.
Troubleshooting by Symptom (Handset)
If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester
(*1) or not.
(*1) or not.
Note:
(*1) A general repair is possible even if you don’t have the DECT tester because it is for confirming the levels, such as Acoustic
level in detail.
(*2) Refer to Check Point (Handset) (P.41)
level in detail.
(*2) Refer to Check Point (Handset) (P.41)
9.3.1.
Check Point (Handset)
Please follow the items below when BBIC or FLASH is replaced.
Note:
After the measuring, suck up the solder of TP.
*: The Setting Method of JIG (Handset) (P.53) is required beforehand.
The connections of adjustment equipment are as shown in Adjustment Standard (Handset) (P.55).
*: The Setting Method of JIG (Handset) (P.53) is required beforehand.
The connections of adjustment equipment are as shown in Adjustment Standard (Handset) (P.55).
Symptom
Remedy (*2)
You don’t have DECT Tester.
You have DECT Tester.
(Model Number: CMD60)
Battery strength is not indicated correctly by Battery icon.
Check item (A) - (D), (E) - (G).
Check item (A) - (D), (E) - (G).
You cannot hear the caller’s voice.
Check item (A) - (C), (H), (N).
Check item (A) - (C), (H - (L)) - (N).
You cannot use handset little away from base unit even if the
handset is within range of the base unit.
handset is within range of the base unit.
-
Check item (I) - (M).
the Audio level is high or low.
Check item (N).
Check item (N).
The SP-Phone level is high or low.
Check item (O).
Check item (O).
Items
Check
Point
Procedure
Check or
Replace Parts
(A)* 1.8 V Supply Adjustment
1.8V
1. Confirm that the voltage between test point 1.8V and GND is 1.8 V ± 0.02 V.
2. Execute the command “VDD”, then check the current value.
3. Adjust the 1.8V voltage of 1.8V executing command “VDD XX“(XX is the
2. Execute the command “VDD”, then check the current value.
3. Adjust the 1.8V voltage of 1.8V executing command “VDD XX“(XX is the
value).
IC1, Q1, C44,
R45, C22,
C41, C45, F1
(B)*
BBIC Confirmation
-
1. BBIC Confirmation (Execute the command “getchk”).
2. Confirm the returned checksum value.
2. Confirm the returned checksum value.
Connection of checksum value and program number is shown below.
IC1, X1, R61
(C)*
VES Confirmation
-
1. VES Confirmation (Execute the command "sendchar EPV").
2. Confirm the returned Value. (Value for reference is written in
2. Confirm the returned Value. (Value for reference is written in
Software_Version_Table.xls).
IC1, IC4, C41
(D) Charge Control Check &
Charge Current Monitor
Check
-
1. Apply 5.0 V between CHG(+) and CHG(-) with DC power supply and set
current limit to 150 mA.
Confirm the indication of “charging” on LCD.
Confirm the indication of “charging” on LCD.
2. Confirm that the current limit LED of DC power supply is ON/OFF.
Confirm it after waiting over 1 minute at least.
(If charge control cannot be confirmed by this procedure, please use battery to
handset power supply and try again.)
handset power supply and try again.)
IC1, Q4 Q9,
Q2, Q3, R2,
Q2, Q3, R2,
R7, R8, R6,
R9, C19, R45
(E)* Charge Detection (OFF)
Check
-
1. Stop supplying 5.0 V to CHG (+) and CHG (-).
2. Confirm the indication of “charging” has been cleared.
2. Confirm the indication of “charging” has been cleared.
IC1, Q4 Q9,
Q2, Q3, R2,
Q2, Q3, R2,
R7, R8, R6,
R9, C19, R45
checksum value
program number
ex.)
9BD2
DF32RP
42
KX-TGJ310/KX-TGJ312/KX-TGJ320/KX-TGJ322/KX-TGJA30
(F)*
Battery Monitor Check
-
1. Apply 2.25 V between BATT+ and BATT-.
2. Execute the command
2. Execute the command
sendchar PAD
sendchar LED 0
sendchar CRX 0 1
sendchar AD1
It assumes that the return value is XX.
a) XX: 70: No need to adjust
b) XX: 66 ~ 6F: Need to adjust
XX: 71 ~ 7A: Need to adjust
Write AD value of 2.25 V to VES.
ex) read data: XX = 6A, write data: YY = 6A
read data: XX = 73, write data: YY = 73
VES = 0009(Low Voltage) write “YY”
Execute the command “wreeprom 00 09 01 YY”.
VES = 000A(No Voltage) write “YY -C"
Execute the command “wreeprom 00 0A 01 ZZ”.
sendchar LED 0
sendchar CRX 0 1
sendchar AD1
It assumes that the return value is XX.
a) XX: 70: No need to adjust
b) XX: 66 ~ 6F: Need to adjust
XX: 71 ~ 7A: Need to adjust
Write AD value of 2.25 V to VES.
ex) read data: XX = 6A, write data: YY = 6A
read data: XX = 73, write data: YY = 73
VES = 0009(Low Voltage) write “YY”
Execute the command “wreeprom 00 09 01 YY”.
VES = 000A(No Voltage) write “YY -C"
Execute the command “wreeprom 00 0A 01 ZZ”.
Note:
ZZ = YY - C
c) XX: 00 ~ 65: Reject
XX: 7B ~ FF: Reject
XX: 7B ~ FF: Reject
IC1, R45
(G)
Battery Low
Confirmation
-
1. Apply 2.40 V between BATT+ and BATT-.
2. Confirm that there is no flashing of Battery Icon.
3. Apply 2.25 V ± 0.08 V between BATT+ and BATT-.
4. Confirm that there is flashing of Battery Icon.
2. Confirm that there is no flashing of Battery Icon.
3. Apply 2.25 V ± 0.08 V between BATT+ and BATT-.
4. Confirm that there is flashing of Battery Icon.
IC1, R45
(H)* BBIC Clock Adjustment
CKM
1. Apply 2.6 V between BATT+ and BATT- with DC power.
2. Input Command “sendchar sfr”, then you can confirm the current value.
3. Check X’tal Frequency. (10.368 MHz ± 100 Hz).
4. If the frequency is not 10.368 MHz ± 100 Hz, adjust the frequency of CKM
2. Input Command “sendchar sfr”, then you can confirm the current value.
3. Check X’tal Frequency. (10.368 MHz ± 100 Hz).
4. If the frequency is not 10.368 MHz ± 100 Hz, adjust the frequency of CKM
executing the command “sendchar sfr xx xx (where xx is the value)” so that the
reading of the frequency counter is 10.368000 MHz ± 5 Hz.
reading of the frequency counter is 10.368000 MHz ± 5 Hz.
Note:
Clear the registered information for Base Unit before measurement, because the
Frequency will not possibly get stable due to the registered information.
Pressing the button of "3" "5" "7" "#"clears the registration.
Register to it on Base Unit after measurement.
Frequency will not possibly get stable due to the registered information.
Pressing the button of "3" "5" "7" "#"clears the registration.
Register to it on Base Unit after measurement.
IC1, X1, C47
(I)*
Transmitted Power
Confirmation
-
Remove the Antenna before starting step from 1 to 7.
1. Configure the DECT tester (CMD60) as follows;
<Setting>
• Test mode: PP
• RFPI: 0102030405
• Traffic Carrier: 5
• Traffic Slot: 4
• Mode: Loopback
• RF LEVEL = -70 dBm
• PACKET: PP32Z
• RFPI: 0102030405
• Traffic Carrier: 5
• Traffic Slot: 4
• Mode: Loopback
• RF LEVEL = -70 dBm
• PACKET: PP32Z
2. Execute the command “sendchar TST 01 02 03 04 05".
3. Initiate connection from DECT tester.
4. Confirm that the NTP value at ANT is 19 dBm ~ 25 dBm.
3. Initiate connection from DECT tester.
4. Confirm that the NTP value at ANT is 19 dBm ~ 25 dBm.
IC1, C859,
C860,
L801,C801,C8
02,C861,C867
02,C861,C867
(J)*
Modulation Check and
Adjustment
-
Follow steps 1 to 3 of (I).
4.Confirm that the B-Field Modulation is -350 ± 50/+350 ± 50 kHz/div using data
type Fig 31.
type Fig 31.
Refer to (I)
(K)*
Frequency Offset
Confirmation
-
Follow steps 1 to 3 of (I).
4.Confirm that the frequency Offset is < ± 20 kHz.
Refer to (I)
(L)*
Sensitivity Receiver
Confirmation
-
Follow steps 1 to 3 of (I).
4.Set DECT tester power to -88 dBm.
5.Confirm that the BER is < 1000 ppm.
5.Confirm that the BER is < 1000 ppm.
Refer to (I)
(M)*
Power RAMP
Confirmation
-
Follow steps 1 to 3 of (I).
4.Confirm that Power RAMP is matching.
Refer to (I)
(N)
Audio Check and
Confirmation
-
1. Link to BASE which is connected to Line Simulator.
2. Set line voltage to 48 V and line current to 50 mA.
3. Input -45 dBm (600
2. Set line voltage to 48 V and line current to 50 mA.
3. Input -45 dBm (600
Ω)/1 kHz to MIC of Handset. Measure the Level at Line I/F
and distortion level.
4. Confirm that the level is -1.5 dBm ± 5 dB (for RU) or -3.5 dBm ± 5 dB (for UC)
and that the distortion level is < 5 % at TEL Line (600
Ω Load).
5. Input -20 dBm (600
Ω)/1 kHz to Line I/F. Measure the Level at Receiver of
Handset and distortion level (Receive volume set to second position from
minimum).
minimum).
6. Confirm that the level is -22 dBm ± 4 dB (for RU) or -23 dBm ± 4 dB (for UC)
and that the distortion level is < 5 % at Receiver (34
Ω Load).
IC1, C12, C11,
C13, MIC,
R23, RA7,
C70, C71,
RA4, C68, C69
Items
Check
Point
Procedure
Check or
Replace Parts
43
KX-TGJ310/KX-TGJ312/KX-TGJ320/KX-TGJ322/KX-TGJA30
(O)
SP phone Audio Check
and Confirmation
-
1. Link to Base which is connected to Line Simulator.
2. Set line voltage to 48 V and line current to 50 mA.
3. Set the handset off-hook using SP-Phone key.
4. Input -30 dBm (600
2. Set line voltage to 48 V and line current to 50 mA.
3. Set the handset off-hook using SP-Phone key.
4. Input -30 dBm (600
Ω)/1 KHz to Line I/F and measure Receiving level at SP+
and SP-.
5. Confirm that the level is -10.0 dBm ± 3 dB and that the distortion level is < 5 %.
(vol = Max at SP (8
Ω Load))
IC1, C78, C79,
R76, R77,
(P)
Charge Pump 3.0 V
Supply Confirmation
CP3V
1. Confirm that the voltage between testpoint CP3.0V and GND is 3.0 V ± 0.3 V.
C30, C53, C29
(Q)
Charge Pump CP4V
Supply Confirmation
Supply Confirmation
CP4V
1. Confirm that the voltage between testpoint CP4V and GND is 4.0 V ± 0.3 V.
(Power is supplied when LED in on)
C52, C55,
C30, C29
Items
Check
Point
Procedure
Check or
Replace Parts
44
KX-TGJ310/KX-TGJ312/KX-TGJ320/KX-TGJ322/KX-TGJA30
10 Disassembly and Assembly Instructions
10.1. Disassembly Instructions
10.1.1.
Base Unit
10.1.1.1. KX-TGJ310
ձ Remove the 4 screws to remove
the cabinet cover.
ձ
4 Screws
Click on the first or last page to see other KX-TGJ310RU / KX-TGJ312RU / KX-TGJ320RU / KX-TGJ322RU / KX-TGJA30RU service manuals if exist.