Panasonic KX-TCD755RUS Service Manual ▷ View online
Address
Default
Name
Type
Description
1EF6
28
AudioRedialBusyDetectTimeout
D
Timeout for busy tone detection after end of dial out.
Unit: 1 Second
Defaults to 40 seconds
1EF7
FF
SmsMmiEnabled
D
Enabled/Disabled Sms Mmi
00=Disabled, all other values=Enabled
1EF8
01
WTMote
D
Walkie Talkie Mode:
00: Common Mode
01: Group Mode
1EF9
01
WTHandsetNo
D
Walkie Talkie Handset Number in Group Mode:
01-09: Valid range
FF: Handset Number not set
1EFA-1EFB
00 00
WTGroupId
D
Walkie Talkie Group ID in Group Mode:
0000-0999: Valid range (BCD coded)
FFFF: Group ID not set
1EFC
00
Sms DeliveryTimeMenuEnabled
D
If FF the delivery time registration screen is available.
1EFD
00
SmsMakeModelMenuEnabled
D
If FF the make/model registration screen is available.
1EDE
FF
Unused1
D
Unused eeprom location
1EDE
FF
Unused2
D
Unused eeprom location
17.3.15. MMI Bits
Address
Default
Name
Type
Description
1F00
0B
EEToneConfig
D
bit 0 = Keytone on/off - 1/0
bit 1 = Call waiting on/off - 1/0
bit 2 = Range alarm on/off - 1/0
bit 3 = Battery lowalarm on/off - 1/0
1F01
C6
UIConfig00
D
bit 0 = Direct call 1=on/0=off
bit 1 = StandbyDisplay00 00=Off/01=TempID
bit 2 = StandbyDisplay01 10=PpNo/11=FpNo
bit 3 = BatteryType 1=Ni-Cd/0=NiMH
bit 4 = Call barring
Bit 5 = Auto talk
Bit 6 = TalkmodelDisplay00 11=Talk time
Bit 7 = TalkmodelDisplay01
01=Talk cost 10=Phone number
17.3.16. Battery Parameters
Address
Default
Name
Type
Description
1F02
A0
LowVoltage
D
Voltage on which to start battery low-indication.
The voltage has to be measured under this value for
8 seconds before the handset start signalling low battery.
LowVoltage[eeprom]=[ADC-steps]=LowVoltage[mV]
(14.35[mV/step])
1F03
99
NoVolatge
D
Voltage on which to turn off handset.
If the battery voltage gets belowthis level and the handset
has been signalling low battery for at least 8 seconds the
handset will shut down.
NoVoltage[eeprom]=
[ADC-steps]=NoVoltage[mV]14.35[mV/step])
1F04
F3
MaxVoltage
D
Max voltage allowed for battery. This is to prevent damage
on hardware if put in base with no batteries mounted.
If the battery voltage exceeds this level, the charging will be
stopped.
MaxVoltage[eeprom]=[ADC-steps]=
MaxVoltage[mV]/14.35[mV/step])
1F05
04
StbyCurrent
D
Current-consumption when not locked to base with buzzer
and backlight off.
UnlockCurrent[eeprom]=comsumption[mA]
1F06
1C
UnlockCurrent
D
Current-consumption when not locked to base with buzzer
and backlight off.
UnlockCurrent[eeprom]=comsumption[mA]
1F07
59
MacHighCurrent
D
Current-consumption when handset is in conversation with
buzzer and backlightoff.
MacCurrent[eeprom]=consumption[mA]
1F08
47
MacLowCurrent
D
Current-consumption when handset is in conversation with
buzzer and backlightoff.
MacCurrent[eeprom]=consumption[mA]
1F09
2E
BackLightCurrent
D
Current consumption when backlight is on. This is only the
consumption for one colour. The value should not include
the consumption of the rest of the handset.
BackLightCurrent[eeprom]=consumtion[mA]
77
KX-TCD755RUS
Address
Default
Name
Type
Description
1F0A
37
BuzzerCurrent
D
Current consumption when Buzzer is playing. This value
should not include any other consumptions than that of the
buzzer.
BuzzerCurrent[eeprom]=consumption[mA]
01FB
78
FastChargeCurrent
D
Charge-current when in fast charge[mA]
The handset is in fast charge-mode when battery-capacity
is less than (chargeTopLimit/100)*MaxCapacity
(BatteryCapacity<ChargeTopLimit%ofMaxCapacity)
1F0C
64
TopChargeCurrent
D
ChargeCurrent when in topoff charge[mA]
The handset charge the batteries with TopChargeCurrent
[mA] when the battery capacity is between
(ChargeTopLimit/100) * Max9NiMH or NiCd) capacity and
´Maxcapacity
(ChargeTopLimit%of MaxCapacity<BatteryCapacity
<maxCapacity)
1F0D
0A
MaintainCurrent
D
Charge-currnt when in maintenance mode needed to
maintain full charge on battery[mA].
This should not include the consumption of the handset
which is handled seperately,
but only the current needed to keep battery at full charge.
(BatteryCapacity=MaxCapacity)
1F0E
5A
TopLimit
D
Percent of max battery capacity to be charged with fast
charge.
When BatteryCapacity reach this limit, the chargecurrent is
switched from FastChargeCurrent to TopChargeCurrent.
1F0F-1F10
00 00
BatteryCap
D
The Current-Capacity left on the battery.
This capacity will always be less than or equal to
MaxCapacity.
It is only used for controlling icons for howmuch capacity is
left on the batteries.
BatteryCapacity[eeprom] = Capacity{mAH]*40[mAh*2/80]=
mAmin*2]4/3(that is 4/3*mA for 2 min)
BatteryCapacity[eeprom] = Capacity{mAH]*40[mAh*2/80]=
mAmin*2]4/3(that is 4/3*mA for 2 min)
17.3.17. VolumeSettings
Address
Default
Name
Type
Description
1F11
10
BeepVolSetting
D
Soundlevel of buzzerbeeps, who is not affected by the
ringervolume.
Hightime = Cycle/VolumeLevel
17.3.18. RedialFAT
Address
Default
Name
Type
Description
1F12-1F1B
80..8
RedialFAT
D
"FileAllocationTable" - for the RedialList
If msb is set it means location is empty
17.3.19. AudioGains
Address
Default
Name
Type
Description
1F1C
16
GX-index
D
Gain-transmit (values ranging from 0x00 to 0x24, each step
representing 1dB). The index represent volumestep 2. See
table.
1F1D
59
GR-index
D
Bit7 - AOG
IBit6 - AOG2
Gain-receive (values ranging from 0x00 to 0x24, each step
representing 1dB). The index represent volumestep 2. See
table.
1F1E
04
SideToneGain
D
SideToneGain (T67DSP-PPV2xD4-7600, table 1.10)
1F1F
11
SpPhGX-index
D
Gain-transmit for speakerphone (values ranging from 0x00
to 0x24, each step representing 1dB). The index represent
volumestep 3. See table.
1F20
98
SpPhGR-index
D
Bit7 - AOG when speakerphone
Bit6 - AOG2 when speakerphone
Gain-receive for speakerphone (values ranging from 0x00
to 0x2A1, each step representing 1dB). The index
represent volumestep 3. See table.
1F22
01
SpPhEnableState
D
Indicates in what state the chip-enable on HF-AM1 has to
be to enable the speakerphone-amplifier
0x01 - P0.7(SP_AMP) set to high enables HF_AM1
0x00 - P0.7(SP_AMP) set to high enables HF_AM1
1F23
16
HeadsetGX-index
D
Gain-transmit when headset mounted (values ranging from
0x00 to 0x24, each step representing 1dB). The index
represent volumestep 2. See table.
78
KX-TCD755RUS
Address
Default
Name
Type
Description
1F24
55
HeadsetGR-index
D
Bit7 - AOG
Bit6 - AOG2
Gain-receive when headset mounted (values ranging from
0x00 to 0x24, each steprepresenting 1dB). The index
represent volumestep 2.See table.
1F25
04
HeadsetSideToneGain
D
SideToneGain when headset mounted
(T67DSP-PPV2xD4-7600, table 1.10)
1F26
80
HeadsetMuteVoltage
D
Determines at which voltage below which the sound in
earpiece/headset will be muted.
HeadsetMuteVoltage[eeprom]=[ADC-steps]=
LowVoltage[mV]/(3.2 * 9.53[mV/step])
1F27
17
HeadsetDetectVoltage
D
Determines at which voltage below which the headset will
be detected.
HeadsetDetectVoltage[eeprom]=[ADC-steps]=
LowVoltage[mV]/(3.2 * 9.53[mV/step])
17.3.20. COMAR-Settings
Address
Default
Name
Type
Description
1F28
79
COMARSetting for speakerphone in
volumelevel 1
D
COMAR for volumelevel 1
1F29
77
COMARSetting for speakerphone in
volumelevel 2
D
COMAR for volumelevel 2
1F2A
74
COMARSetting for speakerphone in
volumelevel 3
D
COMAR for volumelevel 3
1F2B
6F
COMARSetting for speakerphone in
volumelevel 4
D
COMAR for volumelevel 4
1F2C
6C
COMARSetting for speakerphone in
volumelevel 5
D
COMAR for volumelevel 5
1F2D
69
COMARSetting for speakerphone in
volumelevel 6
D
COMAR for volumelevel 6
17.3.21. PowerUpDelay for HF_AM1
Address
Default
Name
Type
Description
1F2E
06
AmpPowerUpDelay
D
Sets the delay from speakerphone-amplifier is enabled until
the first tone is played.
Delay = AmpPowerUpDelay * 10ms
1F2F
0A
AmpPowerDownDelay
D
Sets the delay from speakerphone-amplifier is enabled
uuntil it is completely turned off.
Delay = AmpPowerDownDelay * 10ms
17.3.22. Call Cost-Configuration
Address
Default
Name
Type
Description
1F30
02
MenusEnabled
D
Used to disable/enable functionality
Bit 0: Callcost - 0 disabled/1 enabled
Bit 1: Batteryselection - 0 disabled/1 enabled
17.3.23. Phonebook-FAT
Address
Default
Name
Type
Description
1F31-1FF8
FF
SortedListEeprom
-
Sorted list used in phonebook
17.3.24. WT Battery Parameters
Address
Default
Name
Type
Description
1FF9
0F
Wtstbycurrent
D
Current-consumption when handset is in standby with
buzzer and backlight off.
WTStbyCurrent[eeprom]=consumption[mA]
1FFA
84
WTMacCurrent
D
Current-consumption when handset is in conversation with
buzzer and backlight off.
WTMacCurrent[eeprom]=consumption[mA]
79
KX-TCD755RUS
17.4. Receive and Transmit-gain
The following table shows the legal values for GR-index, SpPhGR-index,
HeadsetGR-index, GR-index, SpPhGR-index and HeadsetGR-index.
HeadsetGR-index, GR-index, SpPhGR-index and HeadsetGR-index.
Possible gain parameters
Eepromvalue
Gain [dB]
00
-23.95
01
-23.03
02
-22.08
03
-21.12
04
-20.03
05
-19.22
06
-17.93
07
-17.01
08
-16.06
09
-15.10
0A
-13.84
0B
-12.88
0C
-11.91
0D
-11.02
0E
-10.05
0F
-8.98
10
-8.06
11
-7.08
12
-6.13
13
-5.03
14
-4.08
15
-3.11
16
-2.00
17
-1.03
18
-0.08
19
0.89
1A
2.05
1B
3.01
1C
3.97
1D
4.94
1E
5.92
1F
7.07
20
8.01
21
8.95
22
10.07
23
11.04
24
12.04
N.B. if the gain-index is set to other values than the ones listed above, the volume will not be working according to specification.
The gain-indexes can be set using the batchfiles WRT_SLR.bat and WRT_RLR.bat, that sets respectively GX- and GR-index.
The gain-indexes can be read from the eeprom using READ_SLR.bat and READ_RLR.bat, that reads respectively GX- and
GR-index.
The gain-indexes can be read from the eeprom using READ_SLR.bat and READ_RLR.bat, that reads respectively GX- and
GR-index.
80
KX-TCD755RUS
Click on the first or last page to see other KX-TCD755RUS service manuals if exist.