Panasonic KX-TCD755RUS Service Manual ▷ View online
17.2. Introduction
17 EEPROM LAYOUT (HANDSET)
17.1. Scope
The purpose of this section is to describe layout of the EEPROM (IC2) KX-A125 handset.
The EEPROM contains hardware, software, and user specific parameters. Some parameters are set during production of the
handset e.g. crystal oscillator adjustment at 0000..01, some are set by the user when configuring the handset e.g. ringer volume
at 0F38, and some during normal use of the phone e.g. redial memory at 0311..0392.
The EEPROM contains hardware, software, and user specific parameters. Some parameters are set during production of the
handset e.g. crystal oscillator adjustment at 0000..01, some are set by the user when configuring the handset e.g. ringer volume
at 0F38, and some during normal use of the phone e.g. redial memory at 0311..0392.
The handset uses a 32k bit serial EEPROM (IC2) for storing volatile parameters. All parameters are set up before the handset
the factory. Some of these are vital for the operation of the hardware so a set of default parameters is programmed before the
actual hardware fine-tuning can be initiated. This document lists all default settings with a short description.
This document lists all default parameters with a short description.
In the tables below values in a range that are similar are not repeated; i.e. Address 00 to 01 contains the value 00 simply means
that the value 00 is repeated in all addressee in the range.
the factory. Some of these are vital for the operation of the hardware so a set of default parameters is programmed before the
actual hardware fine-tuning can be initiated. This document lists all default settings with a short description.
This document lists all default parameters with a short description.
In the tables below values in a range that are similar are not repeated; i.e. Address 00 to 01 contains the value 00 simply means
that the value 00 is repeated in all addressee in the range.
Type
Name
Description
D
default
The EEPROM location is preset to the Default value by the eeprom default loader.
A
adjust
The EEPROM location is set during the production test and should not be overwritten. The value is set by
the eeprom default loader only if the location contains 0xFF, i, e. it has never been set.
-
EEPROM location which is not set at all.
17.3. EEPROM contents
17.3.1. General Setup
Address
Default
Name
Type
Description
0000-0001
?? ??
EepromOscillator
A
Frequency adjustment .............
0002
20
ModulationDeviation
A
Mudulation adjustment
0003
00
InitialTestmode
D
Used when entering testmode
0004-000F
??..??
Reserved
-
Protocol data
0010
88
Pmb7720DRCON
D
DRCON register setting, see T67BMC-DECT-VxxD4-7600
0011
76
Pmb7720CRUCON/
Pmb7720CNUCON
D
CRUCON and CNUCON register setting, see T77BMC-
DECT-VxxT3-7600. CRUCON is used for classic rock
recovery and CNUCON is used for advanced clock
recovery.
0012
00
Pmb7720CRDEL
D
CRDEL register setting, see T77BMC-DECT-VxxT3-7600
0013
11
Pmb7720MCTRL1
D
MCTRL1 register setting, see T77BMC-DECT-VxxT3-7600
0014
9A
Pmb7720MCTRL2
D
MCTRL2 register setting, see T67BMC-DECT-VxxT3-7600
0015
0C
Pmb7720CRRSTART
D
CRRSTART register setting, see T77BMC-DECT-VxxT3-
7600
0016
18
Pmb7720CRRES
D
CRRES register setting, see T77BMC-DECT-VxxT3-7600
0017
02
Pmb7720SYRI
D
BIT0 (LSB): Syri bit setting in OSCTRIMH, T772X-
XV01D5-7600 data
0018
A0
Pmb7720SETTLE
D
SETTLE register setting, see T77BMC-DECT-VxxT3-7600
0019-001A
20 08
Pmb7720SYNINI
D
SYNINI register setting, see T77BMC-DECT-VxxT3-7600
001B
4C
Pmb7720RFINV
D
RFINV register setting, see T77BMC-DECT-VxxT3-7600
001C
0B
Pmb7720PCTRL
D
PCTRL register setting, see T77BMC-DECT-VxxT3-7600
001D
09
Pmb7720VDAL
D
DVAL register setting, see T77BMC-DECT-VxxT3-7600
001E-0020
F3 29 29
Pmb7720Mucon
D
MUCON register setting, see T77BMC-DECT-VxxT3-7600
0021
04
Pmb7720SYNCM_0_Normal
D
SYNCM(0) register setting, see T77BMC-DECT-VxxT3-
7600 during IRC and TBC
0022
0A
Pmb7720SYNCM_0_Rssi
D
SYNCM(0) register setting, see T77BMC-DECT-VxxT3-
7600 during Rssi measuraments
0023
04
Pmb7720SYNCM_0_Search
D
SYNCM(0) register setting, see T77BMC-DECT-VxxT3-
7600 during search for FP
0024
04
Pmb7720WOPNSF
D
WOPNSF register setting, see T77BMC-DECT-VxxT3-
7600
0025
E0
Pmb7720WWSF
D
WWSF register setting, see T77BMC-DECT-VxxT3-7600
0026
00
Pmb7720XCNADJUST
D
XCNADJUST register setting, see T77BMC-DECT-VxxT3-
7600
0027
00
Pmb7720SYNCCTRL
D
SYNCCTRL register setting, see T77BMC-DECT-VxxT3-
7600
0028
00
Pmb7720XFSTLBITS
D
XFSTLBITS register setting, see T77BMC-DECT-VxxT3-
7600
0029
00
Pmb7720XFSTLTLPTRND
D
XFSTLTLPTRND register setting, see T77BMC-DECT-
VxxT3-7600
69
KX-TCD755RUS
Address
Default
Name
Type
Description
002A
0E
Pmb7720RXDSGCNTDEACT0
D
RXDSGCNTDEACT0 register setting, see T77BMC-
DECT-VxxT3-7600. Used in IRC, TBC and during locking
procedure.
002B
00
Pmb7720RXDSGCNTDEACT1
D
RXDSGCNTDEACT1 register setting, see T77BMC-
DECT-VxxT3-7600. Used during RSSI scan and
handover.
002C
16
Pmb7720SYNCM_0_PP_TO_PP
D
SYNCM[0] register setting, see T77BMC-DECT-VxxT3-
7600 in FP mode in Walkie Talkie mode.
002D
0F
Pmb7720DVAL_PP_TO_PP
D
DVAL register setting, see T77BMC-DECT-VxxT3-7600 in
FP mode in Walkie Takie mode
002E-002F
?? .. ??
Reserved
D
Protocol data
0030-0034
00 .. 00
IPEI
A
IEPI
0035
??
Reserved
D
Protocol data
0036-003A
?? .. ??
PARK_1
-
PARK for registration 1
003B-003F
?? .. ??
PARK_2
-
PARK for registration 2
0040-0044
?? .. ??
PARK_3
-
PARK for registration 3
0045-0049
?? .. ??
PARK_4
-
PARK for registration 4
004A
FF
PLI_1
D
Pli for registration 1. If set to FF the registration is
deleted.
004B
FF
PLI_2
D
Pli for registration 1. If set to FF the registration is
deleted.
004C
FF
PLI_3
D
Pli for registration 1. If set to FF the registration is
deleted.
004D
FF
PLI_4
D
Pli for registration 1. If set to FF the registration is
deleted.
004E
73
Powerparameters
D
The following bits control the power management
(BIT0 = LSB):
BIT0: Lowduty cycle
BIT1: Stop CPU when idle
BIT2: Reduce CPU clock
BIT3: Disable DCDC
BIT4: Disable ADC
BIT5: Scan sleep
BIT6: Enable RX Tx lowalgorithm
004F
??
Reserved
-
Protocol data
0050
2A
CoverageBeepLimit
D
Limit for coverage warning algorithm
0051
64
LOW_POWER_RSSI_LIMIT
D
If the RSSI level is belowthis limit, high RF Tx power is
forced.
0052
0A
LOW_POWER_CNT_LIMIT
In the case of A-CRC error or Q1 or Q2 error high power
is forced for LIMIT number of frames.
0053-00EF
?? .. ??
Reserved
-
Protocol data
00F0-00FF
--
ProductionData
-
ProductionData-This area is reserved for KME use.
0100-0104
?? .. ??
RFPI_1
-
RFPI for registration 1
0105
??
SerClass_1
-
Service class for registration 1
0106
??
LAL_1
-
Location area level for registration 1
0107
??
IPUI_LEN_1
-
IPUI length for registration 1
0108-0114
?? .. ??
IPUI_1
-
IPUI for registration 1
0115
??
ZAP_1
-
ZAP for registration 1
0116
??
STATUS_1
-
Status for registration 1
0117-0126
?? .. ??
UAK_1
-
UAK for registration 1
0127-012F
?? .. ??
Reserved
-
Protocol data
0130-0134
?? .. ??
RFPI_2
-
RFPI for registration 2
0135
??
SerClass_2
-
Service class for registration 2
0136
??
LAL_2
-
Location area level for registration 2
0137
??
IPUI_LEN_2
-
IPUI length for registration 2
0138-0144
?? .. ??
IPUI_2
-
IPUI for registration 2
0145
??
ZAP_2
-
ZAP for registration 2
0146
??
STATUS_2
-
Status for registration 2
0147-0156
?? .. ??
UAK_2
-
UAK for registration 2
0157-015F
?? .. ??
Reserved
-
Protocol data
0160-0164
?? .. ??
RFPI_3
-
RFPI for registration 3
0165
??
SerClass_3
-
Service class for registration 3
0166
??
LAL_3
-
Location area level for registration 3
0167
??
IPUI_LEN_3
-
IPUI length for registration 3
0168-0174
?? .. ??
IPUI_3
-
IPUI for registration 3
0175
??
ZAP_3
-
ZAP for registration 3
0176
??
STATUS_3
-
Status for registration 3
0177-0186
?? .. ??
UAK_3
-
UAK for registration 3
0187-018F
?? .. ??
Reserved
-
Protocol data
0190-0194
?? .. ??
RFPI_4
-
RFPI for registration 4
70
KX-TCD755RUS
Address
Default
Name
Type
Description
0195
??
SerClass_4
-
Service class for registration 4
0196
??
LAL_4
-
Location area level for registration 4
0197
??
IPUI_LEN_4
-
IPUI length for registration 4
0198-01A4
?? .. ??
IPUI_4
IPUI for registration 4
01A5
??
ZAP_4
-
ZAP for registration 4
01A6
??
STATUS_4
-
Status for registration 4
01A7-01B6
?? .. ??
UAK_4
-
UAK for registration 4
01B7-01FF
?? .. ??
Reserved
-
Protocol data
17.3.2. MMI Parameters
Address
Default
Name
Type
Description
0200-020C
204=00
DirectCallEntry
D
The first byte is the length of the speed dial number.
The next 12 bytes are the 24 digits. Every digit is 4 bytes
and stored in BCD + some special characters.
020D-028E
--
Redial
D
028F
00
LastRedialEntry
D
0290-0299
FF
HotKey
D
index 0 - speeddialentry for key 0
index 1 - speeddialentry for key 1
-
index 9 - speeddialentry for key 9
029A-029B
00 00
HSPinCode
-
4 BCD Digits
029C
00
EESubscriptionNumber
D
Selected subscription
029D-2A4
00
EESubscriptionInfo
D
HandsetNumber and BaseType for all subscriptions.
02A5-02A6
FF FF
AlarmTime
D
4BCD Digits Hours Tens, Units : Minutes Tens, Units
02A7
00
AlarmConfig
D
bit1 + bit2 - Configuration settings for alarm. 1Byte
00 - OFF
01 - ONCE
10 - DAILY
02A8-02AB
00
TotalHandsetCharge
D
Holds the charge cost count since last handset-reset or call
cost-reset (32bit)
02AC
01
FactoryLanguageSetting
D
Factory setting for language:
00 = German
01 = English
02 = Welsh
03 = Croatian
04 = Spanish
05 = Norwegian
06 = French
07 = Italian
08 = Danish
09 = Dutch
0A = Swedish
0B = Finnish
0C = Greek
0D = Turkish
0E = Hungarian
0F = Portuguese
10 = Russian
11 = Polish
12 = Slovakian
13 = Czechs
14 = Basque
15 = Catalan
16 = Gallego
17 = Irish
02AD
01
Language
D
Language code (see table above)
71
KX-TCD755RUS
Address
Default
Name
Type
Description
02AE-02B0
FF FF FF
Available Languages
D
Bit 0: 0:Disable, 1:Enable German
Bit 1: 0:Disable, 1:Enable English
Bit 2: 0:Disable, 1:Enable Welsh
Bit 3: 0:Disable, 1:Enable Croatian
Bit 4: 0:Disable, 1:Enable Spanish
Bit 5: 0:Disable, 1:Enable Norwegian
Bit 6: 0:Disable, 1:Enable French
Bit 7: 0:Disable, 1:Enable Italian
Bit 0: 0:Disable, 1:Enable Danish
Bit 1: 0:Disable, 1:Enable Dutch
Bit 2: 0:Disable, 1:Enable Swedish
Bit 3: 0:Disable, 1:Enable Finnish
Bit 4: 0:Disable, 1:Enable Greek
Bit 5: 0:Disable, 1:Enable Turkish
Bit 6: 0:Disable, 1:Enable Hungarian
Bit 7: 0:Disable, 1:Enable Portuguese
Bit 0: 0:Disable, 1:Enable Russian
Bit 1: 0:Disable, 1:Enable Polish
Bit 2: 0:Disable, 1:Enable Slovakian
Bit 3: 0:Disable, 1:Enable Czechs
Bit 4: 0:Disable, 1:Enable Basque
Bit 5: 0:Disable, 1:Enable Catalan
Bit 6: 0:Disable, 1:Enable Gallego
Bit 7: 0:Disable, 1:Enable Irish
02B1-02BA
41
Category
D
02BB
00
RunTimeErrorLogConfig
D
00 = ShowRunTimeErrorLog disabled
02BC-02BD
00 00
RunTimeErrorLogAddress
D
0000 = No error
17.3.3. Battery Parameters
Address
Default
Name
Type
Description
02BE-02BF
BB 80
MaxNiMHCapacity
D
Max. Capacity, the battery can be brought up to.
This is used for determining howmuch the battery should
be charged.
MaxNiMHCapacity[eeprom]=
NiMH cap.[mAH]*40 [mAh*2/80]=[mAmin*2]*4/3
(that is 4/3*mA for 2 min)
02C0-02C1
9C 40
MaxNiCdCapacity
D
Max. Capacity, the battery can be brought up to.
This is used for determining howmuch the battery should
be charged.
MaxNiCdCapacity[eeprom]=
NiCd cap.[mAH]*40 [mAh*2/80]=[mAmin*2]*4/3
(that is 4/3*mA for 2 min)
17.3.4. VolumeSettings for Ringerpattern (pattern 1 - 6)
Address
Default
Name
Type
Description
02C2
0A
VolumeLevel1
D
Hightime = Cycle/VolumeLevel
02C3
08
VolumeLevel2
D
Hightime = Cycle/VolumeLevel
02C4
07
VolumeLevel3
D
Hightime = Cycle/VolumeLevel
02C5
06
VolumeLevel4
D
Hightime = Cycle/VolumeLevel
02C6
05
VolumeLevel5
D
Hightime = Cycle/VolumeLevel
02C7
03
VolumeLevel6
D
Hightime = Cycle/VolumeLevel
17.3.5. VolumeSettings for Ringerpattern (pattern 1 - 6)
Address
Default
Name
Type
Description
02C8
1A
VolumeLevel1
D
Hightime = Cycle/VolumeLevel
02C9
0D
VolumeLevel2
D
Hightime = Cycle/VolumeLevel
02CA
0C
VolumeLevel3
D
Hightime = Cycle/VolumeLevel
02CB
09
VolumeLevel4
D
Hightime = Cycle/VolumeLevel
02CC
07
VolumeLevel5
D
Hightime = Cycle/VolumeLevel
02CD
05
VolumeLevel6
D
Hightime = Cycle/VolumeLevel
17.3.6. Cadence-Configuration
Address
Default
Name
Type
Description
02CE
00
Melody 1
D
for external call
00 - Set melody to not followcadence
01 - Set melody to followcadence
72
KX-TCD755RUS
Click on the first or last page to see other KX-TCD755RUS service manuals if exist.