Panasonic KX-TCD755RUS Service Manual ▷ View online
Address
Default
Name
Country
Setting
Type
Description
0A5E
20
PlugD.LvIdleAvgCnt
x
D
Number of samples to use when finding the idle line-
voltage LvIdle
Unit : samples (rate 1/10ms), defaults to 32
0A5F
0A
PlugD.LvDetThresh
x
D
Minimum voltage level in order to detect line-voltage/
plug-in.
Range : 00..FE, FFh=disabled
Unit : adc-steps.
PolA/PolB HW: Default settingcorrespond to line-
voltage below3V
Line-Current HW: see above
0A60
5B
PlugD.LrDetThreshOnh
x
d
Onhook: minimum voltage level in order to detect
polarity.
Range: 00..FE, FFh=disabled
Unit:adc-steps
0A61
45
PlugD.ParDetThreshOnh
x
d
Onhook: threshold for detecting parallel-offhook.
Range : 01..FF, 00h=disabled
Unit:adc-steps
0A62
FF
PlugD.LrDetThreshOffh
x
d
Offhook: minimum voltage level in order to detect
polarity.
Range: 00..FE, FFh=disabled
Unit:adc-steps
0A63
04
PlugD.ParDetThreshOffh
x
D
Offhook: threshold for detecting parallel-offhook.
Range: 01..FF, 00h=disabled
Unit:adc-steps
PolA/PolB HW: Default settingcorrespond to a
delta-detection-voltage of 1V
Line-Current HW: see above
0A64
28
PlugD.CpcMinDisTime
x
D
Offhook: CPC detection, minimum line-current break
time.
Unit: 10ms, range 0.5..FF
0A65
14
LrPeakDetectDiasbleTime
x
Peak detector, line reversal peak-detector disable
time.
During this time the peak-detector will be disabled.
If FFh the ring-detector ignores the line-reversal
detection.
Unit 10ms, Range: 00..FFh, defaults to 200ms.
FSK sender
0A66-67
012C
x
D
FSK detection CIDS_SEIZ
refer to data sheet T77DSPFPV1xD4 for details
0A68-69
0050
x
D
FSK detection CIDS_MARK
refer to data sheet T77DSPFPV1xD4 for details
0A6A-6B
3B01
x
D
FSK detection CIDS_STOP, CIDS_GAIN
refer to data sheet T77DSPFPV1xD4 for details
RCID detection
0A6C-6D
22 A0
C_RCID[0]
x
D
DSP parameter 2D0h
0A6E-6F
00 31
C_RCID[2]
x
D
Gain of RCID-REQ signal
Default: -14.54dB
0A70-71
04 60
C_RCID[3]
x
D
Duration of RCID-REQ signal.
Not used, uses Rcid.ReqWidth parameter instead.
0A72-73
00 08
C_RCID[4]
x
D
Start delay of RCID-DTMF receiver after end of RCID-
REQ signal
0A74-75
8D 25
C_RCID[5]
x
D
DSP parameter 2D4h
0A76-77
1E 10
C_RCID[6]
x
D
DSP parameter 2D5h
0A78-79
0A 10
C_RCID[7]
x
D
DSP parameter 2D6h
0A7A-7B
F9 1A
C_RCID[8]
x
D
DSP parameter 2D7h
0A7C-7D
06 86
C_RCID[9]
x
D
DSP parameter 2D8h
0A7E-7F
B2 B1
C_RCID[10]
x
D
DSP parameter 2D9h
0A80-81
AD A3
C_RCID[11]
x
D
DSP parameter 2DAh
0A82-83
A2 14
C_RCID[12]
x
D
DSP parameter 2DBh
0A84-85
9C B2
C_RCID[13]
x
D
DSP parameter 2DCh
0A86-87
92 C2
C_RCID[14]
x
D
DSP parameter 2DDh
0A88-89
91 46
C_RCID[15]
x
D
DSP parameter 2DEh
0A8A-8B
0D 00
C_RCID[16]
x
D
DSP parameter 2DFh
Peak-detector
0A8C
05
x
D
Peak detect config
Bit
7..4: "no-peak" integrator time, defaults to 50ms
3..0: Peak-cir timeout offset
peak-clr timeout=peak-clr-offset*10ms+50ms
Reserved
0A8D
0D 0E
D
Reserved by the line driver
57
KX-TCD755RUS
Address
Default
Name
Country
Setting
Type
Description
0A8F
F1
D
Reserved by the line driver
16.3.13. DSP-RAM Configuration (for development)
Address
Default
Name
Country
Setting
Type
Description
0A90
FF
DspRamEepCfg1.Addr
x
D
Address of "DSP-RAM configuration" 1
Configuration of the DSP-RAM stops when the first invalid
address is encountered or the last entry is reached.
Range: 02..B0h
0A91-92
FF FF
MSB LSB
DspRamEepCfg1.Data
x
D
Data for "DSP-RAM configuration" 1
0A93
FF
DspRamEepCfg2.Addr
x
D
Address of "DSP-RAM configuration" 2
0A94-95
FF FF
DspRamEepCfg2.Addr
x
D
Data of "DSP-RAM configuration" 2
0A96
FF
DspRamEepCfg3.Addr
x
D
Address of "DSP-RAM configuration" 3
0A97-98
FF FF
DspRamEepCfg3.Addr
x
D
Data of "DSP-RAM configuration" 3
0A99
FF
DspRamEepCfg4.Addr
x
D
Address of "DSP-RAM configuration" 4
0A9A-9B
FF FF
DspRamEepCfg4.Addr
x
D
Data of "DSP-RAM configuration" 4
0A9C
FF
DspRamEepCfg5.Addr
x
D
Address of "DSP-RAM configuration" 5
0A9D-9E
FF FF
DspRamEepCfg5.Addr
x
D
Data of "DSP-RAM configuration" 5
0A9F
FF
DspRamEepCfg6.Addr
x
D
Address of "DSP-RAM configuration" 6
0AA0-A1
FF FF
DspRamEepCfg6.Addr
x
D
Data of "DSP-RAM configuration" 6
0AA2
FF
DspRamEepCfg7.Addr
x
D
Address of "DSP-RAM configuration" 7
0AA3-A4
FF FF
DspRamEepCfg7.Addr
x
D
Data of "DSP-RAM configuration" 7
0AA5
FF
DspRamEepCfg8.Addr
x
D
Address of "DSP-RAM configuration" 8
0AA6-A7
FF FF
DspRamEepCfg8.Addr
x
D
Data of "DSP-RAM configuration" 8
16.3.14. Free Block 3
Address
Default
Name
Country
Setting
Type
Description
0AA8-0DEF
-
Free block
x
-
Free block
16.3.15. SMS Protocol
Address
Default
Name
Country
Setting
Type
Description
0DF0
01
CountryCode
00
d
Country code for SMS Func. 01=D 02=I 03=UK 04=E
0DF1
28
Dll1.ReceiveTimeout
x
d
Receive timeout according to SMS Protocol 1 Std [100ms]
0DF2
C8
Dll1.LinkEstTimeout
x
d
Link Establishement Timeout according to SMS protocol 1
Std[100ms]
0DF3
03
Dll1.RelErrorTimeout
x
d
Timeout for receiving error on last DLL_SMS_REL before
closing connection[100ms]
0DF4
0B
Dll1.InterpacketTimeout
x
d
Timeout between each FSK packet (ETSI - Tl1)[100ms]
0DF5
64
Tl1.ConnectionTimeout
x
d
Connection Timeout on call establishement[100ms]
0DF6
64
Tl1.ReleaseTimeout
x
d
Releae Timeout on call release[100ms]
0DF7
08
Dll2.Timer1
x
d
Max waiting time for receiving an ack from slave[100ms]
0DF8
4C
Dll2.Timer2
x
d
Max waiting time for receiving an ack from master[100ms]
0DF9
4B
Dll2.Timer3
x
d
Max waiting time for receiving "Link estasblished" message
[100ms]
0DFA
23
Dll2.Timer4
x
d
Waiting time for hanging on after release request[100ms]
0DFB
08
Dll2.Timer5
x
d
Waiting time to send ENQ message to maintain active
datalink[100ms]
0DFC
02
Dll2.Timer6
x
d
Waiting time before sending pos.ack without TL payload
[100ms]
0DFD
23
Dll2.Timer7
x
d
Waiting time for forcing diconnection procedure[100ms]
0DFE
02
Dll2.Nretry
x
d
Max number of times to retransmit info and ENQ messages
0DFF
31
Dll2Nwait
x
d
Max number of times to send ENQ message to maintain
data link
0E00
0B
Dll2.InterpacketTimeout
x
d
Timeout between each FSK packet (ETSI - Tl1)[100ms]
0E01
01
FskDrv.InterDigitTimeout
x
d
Max time between to fsk bytes - X*T10_MS
0E02
08
FskDrv.NullMessageTimeo
ut
x
d
Timeout between Null message indication and Header X *
T10_MS
0E03-0E1A
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
CtrlTask.SmscNum 0
x
x
x
x
x
x
x
x
d
First Smsc Number of 24 digits
58
KX-TCD755RUS
Address
Default
Name
Country
Setting
Type
Description
0E1B-0E32
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
CtrlTask.SmscNum 1
x
x
x
x
x
x
x
x
d
Second Smsc Number of 24 digits
0E33-0E4A
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
CtrlTask.SmscNum 2
x
d
Third Smsc Number of 24 digits
0E4B-0E62
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
CtrlTask.SmscNum 0
x
x
x
x
x
x
x
x
d
First Default Smsc Number of 24 digits
0E63-0E7A
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
CtrlTask.SmscDefaultNum
1
x
x
x
x
x
x
x
x
d
Second Default Smsc Number of 24 digits
0E7B-0E92
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
00 00 00
CtrlTask.SmscDefaultNum
2
x
d
Third Default Smsc Number of 24 digits
0E93
00
CtrlTask.SmscSendNum
x
d
Default Smsc sending number
0E94
0A
CtrlTask.SmsAlertTimeout
x
d
Time to wait before (re)trying to collect message [100ms]
0E95
0A
CtrlTask.SmsConnReleas
e-Timeout1
x
d
Time to wait before connection release [10ms]
0E96
1B
CtrlTask.SmsEstCfmDelay
1
x
d
Time to wait before informing TL about SMS call [100ms]
0E97
0A
CtrlTask.SmsConnReleas
e-Timeout2
x
d
Time to wait before connection release [10ms]
0E98
08
CtrlTask.SmsEstCfmDelay
2
x
d
Time to wait before informing TL about SMS call [100ms]
16.3.16. Free Block 4
Address
Default
Name
Country
Setting
Type
Description
0E99-0EFF
-
Free Block4
x
-
Free block
16.3.17. PSTN Line
Address
Default
Name
Country
Setting
Type
Description
0F00
03
UserCfg-1.Mode
01
D
User configuration (MMI) - mode settings 1
Bit
0: "R" mode, 0=earth break, 1=loop break
2..1: Dial mode, 00:pulse, 01:DTMF
3..7: Reserved
0F01
0D
UserCfg-2.Mode
0C
D
User configuration (MMI) - mode settings 2
Bit
0..1: short "R" key time selection
00= short, 01=long, 10=extra-long
2..3: long "R" key time selection
00= short, 01=long, 10=extra-long,
11=undef (uses same time as specified for short R key)
4..7: Reserved
Defaults to 0000 1101
59
KX-TCD755RUS
Address
Default
Name
Country
Setting
Type
Description
0F02
10
UserCfg.RPauseTime
x
D
User configuration (MMI) - "R"-pause. If disabled,
normal dial pause (DialPauseTime) is used.
Bit 7..0 : "R" pause time, zero value allowed
Unit : 50 ms, defaults to 800 ms.
0F03
03
UserCfg.DialPauseTime
x
D
User configuration (MMI) - dial pause.
Bit 3-0 : dial pause in 1 sec units , zero not allowed.
Bit 7-4 : unused
Defaults to 3 seconds
0F04
0F
Cfg-1
2E
D
PSTN line configuration 1 (factory settings)
Bit
0: EarthBreakEnable, Earth break 1=enable 0=disable
1: LoopBreakEnable, Loop break 1=enable,0=disable
2: PulseDialEnable, Pulse dial 1=enable 0=disable
3: RPauseEnable, usage of "R" pause
1=enable, 0=disable
4: PulseType, 0=normalpuls-type
1=(0=1 pils,..9=10 pulss)
5: InterDigitLowImp. controls interdigit impedance.
0: normal impedance during interdigit pause
1: keep low-impedance during interdigit pause
6: LowImpLineSeizure.
Special low-imp line seizure (Australian),
1=enable , 0=disable
7: TwoLines. line config
0=one line, 1=two linesDefaults to 0000 0111B
0F05
15
Cfg-2
14
PSTN line configuration 2 (factory settings)
Bit
0: Meter-pulse,
1=enable, 0=disable
1: DialToneMode, dial tone detection
1=enable 0=disable
2: BusyToneMode. busy tone detection
1=enable 0=disable
3: CurrentLimiterMode,
1=enable, 0=disable
4: RingToneMode. Ring tone detection
1=enable 0=disable
5: HookRelayEnable,
1=enable, 0=disable (if same port is used for earth-
control EarthBreakEnable and HookRelayEnable
cannot both be set to 1)
6..7: not used
Defaults to 0001 0101B
0F06
28
MakeTime
x
D
Pulse make time
Unit: 1ms. defaults to 40ms
0F07
3C
BreakTime
x
D
Pulse break time
Unit: 1ms, defaults to 60ms
0F08
64
DtmfTime
x
D
DTMF tone pulse time.
Unit: 1ms, defaults to 100ms
0F09
0A
InterDigitDtmfTime
x
D
Inter-digit time in DTMF mode
Unit: 10ms , defaults to 100ms
0F0A
4A
InterDigitPulseTime
x
D
Inter-digit time in Pulse mode
Unit: 10ms, defaults to 740ms
0F0B
08
CalibBreakTime[0]
0A
D
Calibrated loop-break time for short break
Unit: 10ms, defaults to 80ms
0F0C
14
CalibBreakTime[1]
x
D
Calibrated loop-break time for long break
Unit: 10ms, defaults to 200ms
0F0D
46
CalibBreakTime[2]
x
D
Calibrated loop-break time for extra-long break
Unit: 10ms, defaults to 700ms
0F0E
28
CalibBreakTime[3]
x
D
Calibrated earth-break time for short break
Unit: 10ms, defaults to 400ms
0F0F
82
CalibBreakTime[4]
x
D
Calibrated earth-break time for long break
Unit: 10ms, defaults to 1300ms
0F10
82
CalibBreakTime[5]
x
D
Calibrated earth-break time for extra-long break
Unit: 10ms, defaults to 1300ms
0F11
FF
LineSeizureEndTime
x
D
Line seizure end-time-time after hook-on.
Meter-pulse detection continues during this period of
time. 00h or FFh means 10ms
Unit: 10ms, defaults to 10ms
0F12
64
RingTermToU100
3C
D
Ring terminate time-out period.
This is the max time that must elapse between two
ring-voltage bursts before the newring-voltage is
registered as a newincoming call.
Unit: 100ms. Defaults to approx 10 sec
60
KX-TCD755RUS
Click on the first or last page to see other KX-TCD755RUS service manuals if exist.