Panasonic KX-TCD755RUS Service Manual ▷ View online
16.3.10. BsUiTask
Address
Default
Name
Country
Setting
Type
Description
09DA-09DD
12,34,56,78 BsUiEngineeringMenuPin
x
D
BCD coded pin code for entering engineering menu
09DE-09E9
-
Reserved for BsCidTask
x
16.3.11. Switch Control
Address
Default
Name
Country
Setting
Type
Description
09EA
00
BaseFeatures
x
D
Bit 0: Base Phonebook: FALSE
Bit 1: Base TAD: FALSE
Bit 2: Base French Clip Handling: FALSE
Bit 3-7: Unused
09EB-09EF
-
Reserved for
BaseFeatures
x
-
09F0
00
Cfg
x
D
Misc. configurations
Bit
0: debug , 1=enable, 0=disable
1..7: not used
09F1
00
HsRegInfo.RegFlags
x
D
Handset registration info - registration
Bit
6..7: not used
0..5: handset 1..6 info, 1=reg, 0=no reg
09F2
00
HsRegInfo.EmcFlags
x
D
Handset registration info - EMC flags
Bit
6..7: not used
0..5: handset 1..6 info, 1=known , 0=unknown
09F3
21
RingMode
x
D
Ring mode. Modes used in KAMMA4 are 20h and 21h.
Bit
7..5: Mode (001=group)
4 : Not used
3..0: Id (001= id of first group)
09F4
03
NumberOfRing
x
D
Number of ring per handset or ring-group
09F5
FF
RingGroup0.HsMask
x
D
Ring-group 0 handset bit-mask
Bit
7: Not used
6..1: Handset 1..6, 1=include, 0=exclude
09F6
12
RingGroup0.Config
x
D
Ring-group 0 configuration
Bit
7..4: next ring-group (1111=none), defaults to ring-group 1
3..2: not used
1: MAC-connection, 0=disabled, 1=enabled, establish MAC
connection to handset(s) during ringing
0 : broadcast ring-status, 0=disabled, 1=enabled
09F7
FF
RingGroup1.HsMask
x
D
Ring-group 1 handset bit-mask. All handsets
09F8
F2
RingGroup1.Config
x
D
Ring-group 0 configuration. No next-group
09F9-09FA
FF F2
RingGroup2
x
-
Ring-group 2
09FB-09FF
-
RingGroup3..5
x
-
Ring-group 3..5
0A00-0A0F
-
Reserved
53
KX-TCD755RUS
16.3.12. PSTN Line Driver
Address
Default
Name
Country
Setting
Type
Description
0A10
00
LiDrv.Config1
x
Line-driver configuration 1
Bit
0: Simulate RCID using DTMF CLIP,
1=enable, 0=disable
1: Debug DTAS/CAS detection, 1=enable, 0=disable
2: Debug Peak detection, 1=enable, 0=disable
3: Debug RCID detection, 1=enable, 0=disable
4: Debug RCID algorithm activate/deactivate,
1=enable, 0=disable
5..7: Not used must be 0
Notes:
1) If simulating RCID using DTMF, the following map
ping is used:
*=repeat character
#=start character
A..D=end-of-rcid-sequence detected.
2) Most of the debug options require mail-trace on
"RECEIVER_NOT_DEFINED" task.
3) If "Debug RCID detection" is 1,
RcidReqTimeoutT3Max controls the period of time
between two request-tones so setting (0F43) to 64H
will result in a time window of 5 secs
0A11
00
LiDrv.Config2
x
Line driver configuration 2
Bit
0: RCID, 1=ignore "invalid-tones" detections
2..4: not used
5: debug, 1=output ring-detect on/off on earth-signal
output
6: debug, 1=output PFLAG on clipimp-signal output
7: debug, 1=output ring-algo activate on clipimp-
signal output
Ring detection
0A12
20
RingDet.Option
x
Ring detect options
Bit
7..6: Unused
5..4: PeakCtrlMode, 00=off, 01=auto, 10=manual
3..1: Unused
0: DCON5.ACF, correction filter,
1=enable, 0=disabled
(recommend not to use this filter!!)
Notes:
PeakCtrlMode determines howthe peak-detector
controls the activation/deactivation of the ring-detect
algorithm.
off: peak-detector does not control the ring-detect
algorithm, instead the algorithm is activated once
when entering on-hook state.
auto: peak-detector+dsp-firmware controls the
ring-detect algorithm automatically
(SW sets DCON5.RGS=1)
manual: peak-detector+SW controls the ring detector
algorithm.
The SW polls the APDET.PFAG and activates/
deactivates the ring-algorithm accordingly.
This is the method recommended.
If peak-detection is disabled
(APDET Onhook.PEN=0, address 0208) the
PeakCtrlMode setting is ignored and assumed to be
be "off".
0A13
7C
RingDet.RHystH
x
High-level of zero-crossing counter hysteresis.
Refer to datasheet T77DSP- FPV1xD4-760, p100-
103 for further details about the RingDet parameters.
Recommend that RONLEV, RHYSTH and RHYSTL
have the same value in dB !!
Default: ??dB, range: 00..7Fh
0A14
7C
RingDet.RonLev
x
Min. peak level of ringer signal start-detection.
Default: ??dB, signed, range : 00..7Fh
0A15
84
RingDet.RHystL
x
Low-level of zero-crossing counter hysteresis.
Default: ??dB, signed, range: [80,81,..FF,00]
0A16
7B
RingDet.RoffLev
x
Min. peak level of ringer signal end-detection.
Default: ??dB, range: 00..7Fh
54
KX-TCD755RUS
Address
Default
Name
Country
Setting
Type
Description
0A17-18
00 F8
RingDet.RCntMin
x
Ring detection, min. number of 8Khz cyles between
first and last node
RCntMin=4000/fmax*(RNodeNo-1)
Default:64Hz
0A19-1A
03 93
RingDet.RCntMax
x
Ring detection, max number of 8Khz cyles between
first and last node
RCntMin=4000/fmax*(RNodeNo-1)
Default:18Hz
0A1B
2A
RingDet.RMaxTime
x
Ringing end/line-reversal timer. The setting must be
larger than (1/fmin)/2
Default: 42ms
0A1C
05
RingDet.RNodeLr_No
x
Number of nodes (zero-crossings).
Bit 4..7: RNodeLr, number of accepted nodes during
LR detection
Bit 0..3: RNodeNo, number of nodes to be used for
frequency measurement
RNodeNo defaults to 5 (2 periods)
15Hz: T=66.7ms, 3*66.7ms=200.1ms
FSK detection
0A1D-1E
00 80
FSKDet.C_CID_LEV
00 6D
D
FSK detection, CID sensitivity level
Refer to the T77DSPF-FPV1xD4-760 datasheet, p94-
97 for further details about the CID parameters.
Formula:
Default: -45dBm0
0A1F-20
00 5A
FSKDet.C_CID_SEIZ
x
D
FSK detection, minimum seizure length
Range: 1..7FFFh
0A21-22
00 28
FSKDet.C_CID_MARK
x
D
FSK detection, minimum, ark length
Range: 1..7FFFh
0A23-24
80 81
FSKDet.C_CID_MTYB12
x
D
FSK detection, allowed start sequence 1 and 2
0A25-26
82 86
FSKDet.C_CID_MTYB34
x
D
FSK detection, allowed start sequence 3 and 4
0A27-28
04 06
FSKDet.C_CID_MTYB56
x
D
FSK detection, allowed start sequence 5 and 6
0A29-2A
06 06
FSKDet.C_CID_MTYB78
x
D
FSK detection, allowed start sequence 7 and 8
0A2B-2C
7F FF
FSKDet.C_CID_STOP
x
D
FSK detection, maximum number of stop bits
Range: 1..7FFFh
DTMF detection
0A2D
40
DTMFDet.DPOW
34
D
DTMF detection, sensitivity power-level.
Refer to the T77DSP-FPV1xD4-760 datasheet,
p85-90 for further details about the DTMF-DET
parameters.
Formula: DPOW [dBm0=-93.32+DPOW*0.7525
Default: -45dB0
0A2E
0D
DTMFDet.DTWIST
x
D
DTMF detection, allowed twist
Default: 9.8dB
0A2F
0D
DTMFDet.DPHB
x
D
DTMF detection, distance power in high-band and
and DTMF frequency power
Default: 9.8dB
0A30
04
DTMFDet.DTIMP
x
D
DTMF detection, max allowed time break
Default: 1ms
0A31
13
DTMFDet.DPGB
x
D
DTMF detection, distance power of GAP band and
DTMF frequency power
Default: 14.3dB
0A32
07
DTMFDet.DHYST
x
D
DTMF detection, hysteresis of zero-crossing counter
Default: -74dB
0A33
0F
DTMFDet.DTSIG
x
D
DTMF detection, time for signal detection
Default: 16ms
0A34
1D
DTMFDet.DTPAUSE
x
D
DTMF detection, time for pause detection between
two DTMF characters.
Default: 30ms
0A35-36
00 01
DTMFDet.DTFR5
x
D
DTMF detection, time for break during a charater
Default: 2ms
FSK dual-tone detection
0A37
28
DtasDet.C_ATD1-1
x
D
DTAS detection, detection level for DTAS (on-hook).
Refer to the T77DSP-FPV1xD4-760 datasheet, p90-
93 for further details about the DtasDet-parameters.
Default: -30dBm0
0A38
28
DtasDet.C_ATD1-1
x
D
DTAS detection, detection level for CAS (off-hook).
Default: -30dBm0
0A39-3A
E8 FE
DtasDet.C_ATD2
x
D
DTAS detection C_ATD2, defaults to 1.1%
0A3B-3C
B0 C2
DtasDet.C_ATD3
x
D
DTAS detection C_ATD3, defAaults to 1.1%
0A3D-3E
A1 9B
DtasDet.C_ATD4
x
D
DTAS detection C_ATD4, defAaults to 1.1%
CPT detection
55
KX-TCD755RUS
Address
Default
Name
Country
Setting
Type
Description
0A3F-40
CC 5B
ProgressDet.C_CPT1
x
D
Progress tone detection C_CPT1
Refer to the T77DSP-FPV1xD4-760 datasheet, p81-
85 for further details about the DtasDet-parameters.
FC=438Hz
0A41-42
92 31
ProgressDet.C_CPT2
x
d
Progress tone detection C_CPT2
BP-width=535Hz
0A43-44
92 31
ProgressDet.C_CPT3
x
d
Progress tone detection C_CPT3
BS-width=535Hz
0A45-46
41 10
ProgressDet.C_CPT4
x
d
Progress tone detection C_CPT4
LIM_T=-84dB
0A47-48
0A 05
ProgressDet.C_CPT5
x
d
Progress tone detection C_CPT5
0A49-4A
04 48
ProgressDet.C_CPT6
F4 38
d
Progress tone detection C_CPT6
LEV_T=-30dB
0A4B-4C
7F 03
ProgressDet.C_CPT7
x
d
Progress tone detection C_CPT7
Meter-Pulse detection
0A4D
01
MpDet.Cfg
x
d
MP-detection, configuration
Bit 0..1: 0=disable, DSP detector=1, 2=MPINP
detector (not supported)
Bit 2..3: Frequency, 12KHz-01 16KHz=00
Bit 4..7: 0
0A4E
3F
MpDet1.Ctrl
x
D
Reserved for "MP-detection control MpInp)"
Bit 0..1: Hysteresis, 11=+/-0.5LSB
Bit 2..3: MPCGain 11=gain is 8
Bit 4: GGISel, 1=use tolerant circuit, 0=use in-tolerant
circuit
Bit 5: MPC input ADREF offset - 0=disable, 1=enable
Bit 6: LS, 1=use level-shifter, 0=disable level-shifter
Bit 7: 0
Refer to description of registers: MPCCTR,
METPULSE
0A4F
00
MpDet1.MpcMv
x
D
Reserved for "MP-detection (MpInp), mean value of
comparator"
Refer to description of registers: MPCMV
0A50
39
MpDet2.MpLevStart
x
D
MP-detection (DSP), signal-level for detection start.
0A51
39
MpDet2.MpLevEnd
x
d
MP-detection (DSP), signal-level for detection end.
0A52
02
MpDet2.MpTimSigMin
x
d
MP-detection (DSP), min. signal duration.
0A53
52
MpDet2.MpTimSigMax
x
d
MP-detection (DSP), max. signal duration
0A54
0E
MpDet2.MpTimPause
x
d
MP-detection (DSP), min pause-time
0A55
42
MpDet2.LPMF
x
d
MP-detection (DSP), LP time constant
0A56
00
MpDet2.Mp---
x
d
MP-detection (DSP), ?
0A57
09
MpDet2.MpTimDropOut
x
d
MP-detection (DSP), allowed time for dropouts
Line AGC
0A58
3C
AGC.Vmax
x
D
Upper VAGC limit. AGC adustment is carried out from
AGC.Vmin to AGC.Vmax
Unit: ADC steps
Notes: If AgcUpdateTime(0F14) is FF, line-AGC is
disabled and the line-AGC driver parameters does not
matter.
0A59
28
AGC.Vmin
x
d
Lower VAGC limit
Unit: ADC steps
0A5A
02
AGC.VHysteresis
x
d
VAGC hysteresis
Unit: ADC steps
0A5B
2D
AGC.Steps
x
d
SLR and RLR steps
Bit 0-2: SLR steps, range 2-7 (0=disable SLR AGC)
Bit 5-3: RLR steps, range 2-7 (0=disable RLR AGC)
Bit 6-7: Not used
Defaults to 5 SLR and 5 RLR steps
Plug/Pol detection
0A5C
20
PlugD.Option
A0
D
Plug/Pol detection options:
Bit 0: par, 1=detect parallel offhook, 0=disable
Bit 1: Plug, 1=detect plug in/out, 0=disable plug in/out
Bit 2: CPC, 1=enable CPC, 0= disable CPC
Bit 3..4: Unused
Bit 5: Hw_PolAdc, pol-A+pPol-B adcs,
1=present, 0=not present
Bit 6: Hw_AgcAdc, AGC-adc,
1=present, 0=not present
Bit 7: Enable detector, 1=enable, 0=disable,
Disabling the detector overrules all other options.
0A5D
0A
PlugD.IntegrateTime
x
D
Integrate-time for detecting plug-in/out, line-reversal,
and parallel-offhook.
If FFh plug/pol detection is completely disabled.
Unit : 10ms, defaults to 100ms
56
KX-TCD755RUS
Click on the first or last page to see other KX-TCD755RUS service manuals if exist.