Panasonic KX-TCD755RUS Service Manual ▷ View online
Address
Default
Name
Country
Setting
Type
Description
0F13
08
RingPatternToU100
x
D
Ring pattern timeout. Max. silence period during
distinctive ringing.
As long as the silence period does not exceed this
this period of time the ring is still considered and
counted as one single ring.
Unit: 100ms. Defaults to 800ms
0F14
FF
AgcUpdateTime
x
D
Line AGC update time.
The period of time between each line AGC update.
If FFh, line-AGC is disabled.
If used recommended value is 64h (1 sec).
Unit: 10ms, min/max: 10/FF, Defaults to disabled
0F15
0A
LineSeizureTime
x
D
Line seizure time. The period of time that the PSTN line
or the PSTN HW needs after the hook-switch is
activated in order to be ready.
During this period audio is muted.
Only used during outgoing calls or if the special-line
seizure mode is enabled (Cfg:6).
Unit: 10ms, min/max: 01/FF. Defaults to 100ms
0F16
66
InitDialPause
x
D
Init-dial-pause. Dial pause inserted after hook-off when
making an outgoing call.
Bit 0..3: init dial pause if PULSE dial-mode.
If 0fH then normal dial-pause is used.
Bit 4..7: init dial pause if DTMF dial-mode.
if 0fH then normal dial-pause is used.
Unit: 500ms, min/max: 00/0F.
Defaults to 3 sec and 3 sec.
0F17
10
LineSeperationTimeU100
x
D
Line separation time (IWU_IWU_SEPARATION_REQ
Unit: 100ms. Defaults to 1600ms
0F18
00
PulseInitialDelayU10
x
D
Initial pulse-dial delay. During this period of time,
audio will be muted and the line impedance low.
00H is allowed. Unit 10ms,
Defaults to 0ms meaning disabled.
0F19..1F1B
FF,FF,FF
Reserved[3]
x
D
Reserved by line-task
16.3.18. Clip configuration
Address
Default
Name
Country
Setting
Type
Description
0F1C
70
Detect
04
D
CLIP detect configuration
Bit
0-2: Mode: 0: Learn mode, 1: DTMF only, 3: Generic
mod, 4: Russian CLIP only
3: Unused4
4: Onhook: 1=enable 0=disable
5: Offhookk: 1=enable 0=disable
6: Msgwaiting: 1=enable 0=disable
7: Unused7
0F1D
05
Options
x
D
CLIP detect options
Bit
0: MuteOnCas: 1=enable 0=disable
1: AttenuateOnCas: 1=enable 0=disable
2: AckParallelPhone: 1=enable 0=disable
3: CasOnOnly: 1=enable 0=disable
4: Unused4
5: Unused5
6: Unused6
7: Unused7
0F1E
00
Ring configuration
x
D
Ring configuration
Bit
0: Rpas: 1=enable 0=disable
1: RpasAlert: 1=enable 0=disable
2: Rpas2LongAlert: 1=enable 0=disable
3: Power: 1=enable 0=disable
4: PowerAlert: 1=enable 0=disable
5: Silence: 1=enable 0=disable
6: SuppressFirstRing: 1=enable, 0=disable
7: Unused7
0F1F
12
Rpas.RpasMinDuration
x
D
RPAS maximum duration.
Unit : 10ms, defaults to 180ms.
0F20
20
Rpas.RpasMaxDuration
x
D
RPAS maximum duration.
Unit : 10ms, defaults to 320ms.
61
KX-TCD755RUS
Address
Default
Name
Country
Setting
Type
Description
0F21
00
Dtas.Configuration
x
D
DTAS Configuration
Bit
0: TimeValidate: 1=enable 0=disable
Enabled:
DTAS pulse width is examined and validated.
Disabled:
DTAS start is used as FSK trigger.
1: Unused1
2: Unused2
3: Unused3
4: Unused4
5: Unused5
6: Unused6
7: Unused7
0F22
00
Dtas.SilenceTimeout
x
D
Silence period after RPAS.
Unit: 10ms, defaults to 0ms.
0F23
3C
Dtas.DtasMinDuration
x
D
DTAS minimum duration.
Unit: 1ms, defaults to 60ms.
0F24
82
Dtas.DtasMaxDuration
x
D
DTAS maximum duration.
Unit: 1ms, defaults to 130ms.
0F25
3C
Dtas.DataTimeout
x
D
DTAS to FSK data timeout
Unit: 10ms, defaults to 600ms.
0F26
01
Clip.ImpSet
x
D
Impedance set configuration
Bit
0: Polarity: 1=enable 0=disable
1: DtasStart: 1=enable 0=disable
2: DtasEnd: 1=enable 0=disable
3: Rpas: 1=enable 0=disable
4: RpasSilence: 1=enable 0=disable
5: PowerRing: 1=enable 0=disable
6: Unused6
7: Unused7
0F27
0F
Clip.ImpRemove
x
D
Impedance remove configuration
Bit
0: Polarity: 1=enable 0=disable
1: Ringing: 1=enable 0=disable
2: ClipReceived: 1=enable 0=disable
3: Offhook: 1=enable 0=disable
4: Unused4: 1=enable 0=disable
5: Unused5: 1=enable 0=disable
6: Unused6
7: Unused7
0F28
0A
Clip.ImpTimeout
x
D
CLIP impedance set timeout
Unit : 100ms, defaults to 1000ms.
0F29
32
Cas.MinDuration
x
D
CAS minimum duration.
Unit : 1ms, defaults to 50ms.
0F2A
82
Cas.MaxDuration
x
D
CAS maximum duration.
Unit : 1ms, defaults to 130ms.
0F2B
00
Cas.AckDelayTimeout
x
D
CAS to Acknowledge DTMF Delay Timeout.
Unit : 1ms, defaults to 0ms.
0F2C
0D
Cas.AckDtmf
x
D
CAS acknowledge DTMF tone
00: DTMF 0
09: DTMF 9
---- ----
0A: DTMF A
0B: DTMF A
0C: DTMF B
0D: DTMF D
0E: DTMF *
0F: DTMF #
Defaults to DTMF D
0F2D
3C
Cas.AckDuration
x
D
Acknowledge DTMF tone duration.
Unit : 1ms, defaults to 60ms
0F2E
3C
Cas.DataTimeout
x
D
CAS to FSK data timeout
Unit : 10ms, defaults to 600ms
0F2F
00
Dtmf.StartCpn
x
D
User defined DTMF start of calling party number
Defaults to: Disabled.
0F30
00
Dtmf.StartForward
x
D
User defined DTMF start of last forwarding number
Defaults to: Disabled
0F31
00
Dtmf.StartReason
x
D
User defined DTMF start of reason code
Defaults to: Disabled
0F32
00
Dtmf.StartVmwi
x
D
User defined DTMF start of Visual Message Waiting
Indication code.
Defaults to: Disabled
0F33
00
Dtmf.Stop
x
D
User defined DTMF stop code
Defaults to: Disabled
62
KX-TCD755RUS
Address
Default
Name
Country
Setting
Type
Description
0F34
32
Dtmf.InterdigitTimeout
x
D
DTMF Interdigit Timeout
Unit : 10ms, defaults to 500ms
0F35
08
Fsk.InterdigitTimeout
x
D
FSK Interdigit Timeout
Unit : 10ms, defaults to 80ms.
0F36
0A
Fsk.MarkoutTimeout
x
D
FSK Markout Timeout after FSK received
Unit : 10ms, defaults to 100ms
0F37..38
3D 01
Parse.Configuration
3D 00
D
Clip parse set configuration
Bit
0: Etsi: 1=enable 0=disable
1: ForwardNumber: 1=enable 0=disable
2: Danish: 1=enable 0=disable
3: Dutch: 1=enable 0=disable
4: Canadian: 1=enable 0=disable
5: Swedish: 1=enable 0=disable
6: UserDefined: 1=enable 0=disable
7: KPN vmwi: 1=enable 0=disable
8: ProtocolPriority:
If 2 mutual exclusive parameters occurs, the 1st in
the protocol message has priority.
9: UseCallType:
Verify the Call Type parameter, if available, when
receiving Call Back CLIP at busy subscriber.
1=enable 0=disable
10..15: Reserved10..Reserved15
0F39
0E
RingVmwi.MinTime
x
D
KPN Visual Message Waiting Indication minimum
ring time.
Unit: 1 second. Defaults to 14 seconds.
0F3A
16
RingVmwi.MaxTime
x
D
KPN Visual Message Waiting Indication minimum
ring time.
Unit: 1 second. Defaults to 22 seconds.
0F3B
00
RingVmwi.RingEndTime
x
D
KPN Visual Message Waiting Indication last ring to
to call timeout.
Unit: 100ms. Defaults to 0
0F3C
3C
RingVmwi.RingPulseMin
x
D
KPN Visual Message Waiting Indication minimum
ring pulse time.
If ring pulse duration is less than RingPulseMin,
the KPN voice mail is not activated.
( To avoid WMVI behind a PABX)
Unit: 10ms. Defaults to 600ms
0F3D
00
Rcid.Mode
x
D
RCID mode
Bit
0: answer-mode,
1=auto-answer, 0=manual answer
1..4: 0
5: detect length,
1=enable(development only), 0=disable
6: add category,
1=enable(development only), 0=disable
7: 0
0F3E
71
Rcid.Options
x
D
RCID mode
Bit
1..3: 0
4: pre-detect before first RCID-request,
1=enable, 0=disable
5: emulate ring-back tone,
1=enable, 0=disable
6: detect ring-timming,
1=enable, 0=disable
7: 0
0F3F
73
Rcid.PacketLen_RetryCnt
x
D
RCID mode packet length and request retry count
Bit
7..4: Packet length including start/begin+category
(default 9)
3..0: Request-Retry Count (default 3)
0F40
01
Rcid.RingCntToStart
x
D
RCID, number of rings before auto-answering call
0: on first ring-volt-off
1..9: on 1-9 ring pattern-off
0F41
04
Rcid.LineSeizureT0
x
D
RCID line-seizure delay
Unit: 50ms, defaults to 200ms.
63
KX-TCD755RUS
Address
Default
Name
Country
Setting
Type
Description
0F42
00
Rcid.ReqDelayT1
x
D
RCID-request delay parameter T1
Delay from line-seizure to 1.
Req-tone: T0+T1 (200ms)
Delay between two req-tones if no data:
T1+T3max (600ms)
Dealy between data and next req-tone:
T1+T7T8 (150ms)
Unit: 1ms, defaults to 0ms
0F43
0E
Rcid.ReqWidthT2
x
D
RCID-request width (T2)
Unit: 10ms, defaults to 140ms
0F44
04
Rcid.ReqTimeoutT3Max
x
D
RCID-request to "first RCID data" timeout (T3Max)
Unit: 50ms, defaults to 600ms
0F45
04
Rcid.DataTimeoutT7T8Max
x
D
RCID next-digit timeout (T7+T8)max
Unit: 50ms, defaults to 150ms
0F46
02
Rcid.SimRingCnt
x
D
RCID simulated-ring count
0F47
38
Rcid.SimRingOnOffTime
x
D
RCID simulated-ring timing
Bit
0..3: ring-on time
4..7: ring-off time
Unit: 50ms, defaults to 1.5s ring-on time,
4s ring-off time
0F48
01
Rcid.MaxErrCnt
x
D
RCID, max error-count during parsing
0F49-4A
FF..FF
Reserved[4]
x
D
16.3.19. BsUiTask settings
Address
Default
Name
Country
Setting
Type
Description
0F4B
01
Config1
33
D
BsUiTask configuration (MSB)
Bits 1=enable 0=disable
0: AmPmClockSettingEnabled, enabled
1: ClipDetectionSettingEnabled, disabled
2: AkzMenuEnabled, disabled
3: HakzMenuEnabled, disabled
4: RussianClipSttingEnabled, disabled
5: SmscSendNumberSettingEnabled, disabled
6-7: Unused
0F4C
F7
Config2
D7
D
BsUiTask configuration (LSB)
Bits 1=enable 0=disable
0: FlashTime1Enabled, enabled
1: FlashTime2Enabled, enabled
2: FlashTime3Enabled, enabled
3: KeyClicksEnable, enabled
4: ARSCarrierMenuEnabled, enabled
5: ARSIntDeletionMenuEnabled, enabled
6: ARSMultipleCarrierMenuEnabled, enabled
7: ARSMultipleAreaCodeMenuEnabled, enabled
0F4D
-
UserData.SmsPabxSuport
-
-
SMS PABX Support On/Off
16.3.20. EepromInRam Reserved
Address
Default
Name
Country
Setting
Type
Description
0F43-FF
-
EepromInRam Reserved
-
-
Reserved for EepromInRam
16.3.21. SMS Storage
Address
Default
Name
Country
Setting
Type
Description
1000
0E
SendQueueInitTime
x
D
Time to first SMS send attempt, unit=seconds
1001
0F
AlertIndicationInitTime
x
D
Time from Alert Indication to first SMS retrieve
attempt, unit=seconds
1002
02
SendQueueRetryTime
x
D
Time Between SMS sending attempts
1003
04
SendQueueRetries
x
D
Number of SMS sending attempts
1004-5
00,00
IncrementingMessageID
x
D
Incrementing outgoing massage number
1006
01
Terminal ID
x
D
Terminal Identifier
1007
00
DeliveryTimeRegistration
x
D
Indicates if Delivery Time shall be registered at
SMSC upon first entry into SMS messages menu.
1008
00
MakeModelRegistration
x
D
Indicates if Make/Model shall be registered at SMSC
upon first entry into SMS messages menu.
64
KX-TCD755RUS
Click on the first or last page to see other KX-TCD755RUS service manuals if exist.