Panasonic KX-TC1019RUB Service Manual ▷ View online
14 EXPLANATION OF ID CODE
14.1. General Information
1. The ID CODE for KX-TC1019RUB consists of 5-digit numbers between "00000" ~ "65535". They are stored into the base unit
and portable unit respectively. The ID CODE is found in the label on the bottom of each cabinet of the base unit and portable
unit.
unit.
14.2. ID Writing (For service activity)
The explanation of the method of writing this ID is used to write ID besides ID of the set when the person in charge of service
repairs the set.
repairs the set.
<Writing Procedure>
(Refer to .)
1. Install the resister R909 to the base unit, and turn the power ON.
•
The base unit enters the RX waiting mode at the special channel
2. Insert the battery into the portable unit while pressing the keys of 2, 7 and # at the same time.
•
“ID code write” is displayed on the LCD of the portable unit.
3. Press the TALK button of the portable unit.
•
The portable unit and base unit are linked at the special channel. (As for the special channel, refer to .)
4. Press the ID CODE of 5 digits using the decimal system from the portable unit aceoding to ID of the ID label.
•
ID=00000~65535
5. Press the TALK button of the portable unit.
•
The portable unit transmits the ID writing request data.
•
When the base unit receives the data, a new ID is written in the EEPROM of the base unit, then it transmits “ID
confirmation data” to the portable unit.
confirmation data” to the portable unit.
•
When the portable unit receives the data, the ID is written in the EEPROM of the portable unit, then the confirmation tone
(Pi -) will sound.
(Pi -) will sound.
Note: when ID writing is failed, the error sound (Pi Pi) will be output. At that time, RF block and EEPROM of the base unit
and portable unit should be checked.
and portable unit should be checked.
6. Turn OFF the power of the base unit, and then remove the resister R909.
7. Turn ON the power of the base unit and charge the portable unit to recover from Test mode, and check the link operation
inorder to confirm New ID is written in portable and Base, both.
* In case of mistaking operation, restart from step 2.
25
KX-TC1019RUB
14.3. FREQUENCY TABLE (MHz)
26
KX-TC1019RUB
15 ADJUSTMENTS (BASE UNIT)
If your unit have below symptoms, adjust or confirm each item using remedy column from the table.
Symptom
Remedy
The base unit dose not respond to a call from portable unit.
Make adjustments in item (A)
The base unit dose not transmit or the transmit frequency is off.
Make adjustments in item (B)
The transmit frequency is off.
Make comfirmation in item (C)
The transmit power output is low, and the operating distance between base unit
and portable unit is less than normal.
and portable unit is less than normal.
Make comfirmation in item (D)
The reception sensitivity of base unit is low with noise.
Make comfirmation in item (E)
The transmit level is high or low.
Make comfirmation in item (F)
The reception level is high or low.
Make adjustments in item (G)
The unit does not link.
Make comfirmation in item (H)
15.1. Test Mode Flow Chart (Base Unit)
The operation-flow of Test mode and main check items are shown below.
R910, Test mode SW : Refer to .
27
KX-TC1019RUB
15.2. How to set the test mode
Remove the antenna lead wire from P.C.Board of the base unit.
The connection of test mode are shown in
15.3. Adjustment
The connection of adjustment equipments are as shown in ,
SSG Frequency : 40.000 MHz
28
KX-TC1019RUB
Click on the first or last page to see other KX-TC1019RUB service manuals if exist.