DOWNLOAD Panasonic PT-DZ780 / PT-DW750 / PT-DX820 / PT-DZ780BE / PT-DZ780LBE / PT-DZ780LWE / PT-DZ780WE / PT-DW750BE / PT-DX820BE / PT-DX820LBE (serv.man2) Service Manual ↓ Size: 59.12 MB | Pages: 104 in PDF or view online for FREE

PREFACE

< DZ780/DW750/DX820 >

 Accuracy : 

≦

 2%

 Input resistance :

≧

 1 MΩ

 Input capacitance :

≦

 200 pF

 Frequency range :

15 Hz to 1 MHz

1. Prepare the measuring circuit as shown in Fig.1.
    Be sure to use a voltmeter having the performance described in Table 1.
2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet.
3. Connect M1 to T1 according to Fig. 2 and measure the voltage.
4. Change the connection of M1 from T1 to T2 and measure the voltage again.
5. The voltmeter must read 0.375 V or lower in both of steps 3 and 4.  This means that the current must be 0.75mA
    or less.
6. If the reading is out of the above standard, the projector must be repaired and rechecked before returning to the
    customer because of a possibility of an electric shock.

- For continued safety, no modification of any circuit must be attempted.
- Unplug the power cord from the power outlet before disassembling this projector.
- Use correctly the supplied power cord and must ground it.
- It is advisable to use an isolation transformer in the AC power line before the service.
- Be careful not to touch the rotation part (cooling fan, etc.) of this projector when you service with the upper
  case removed and the power supply turned ON.
- Observe the original lead dress during the service. If a short circuit is found, replace all the parts overheated
  or damaged by the short circuit.
- After the service, all the protective devices such as insulation barriers, insulation papers, shields, and isolation
  R-C combinations must be properly installed.
- After the service, check the leakage current to prevent the customer from getting an electric shock.

- Be sure to unplug the power cord from the power outlet when replacing the lamp.
- Because the lamp reaches a very high temperature during its operation, wait until it cools completely when replacing
  the Lamp Unit.
- The lamp emits small amounts of UV-radiation, avoid direct-eye contact with the light.
- The lamp unit has high internal pressure. If improperly handled, explosion might result.
- Because the high pressure lamp involves a risk of failure, never touch the lamp wire lead during the service.

Performance

 Voltmeter
 (rms reading)

Table. 1

M1

M2

Rs

Rb

Cs

10 kΩ ±0.1%

V

Vb

(V)

0.022μF
±1.0%

to T1
or T2
in FIG.2

Rs:1500 Ω ±0.1%
Cs:0.22μF ±1.0%
Rb:500 Ω ±0.1%

Weighted leakage current = Vb / 500 (A)

M1

M2

T1

T2

Isolation transformer

to power outlet

Measuring
circuit (Fig.1)

Multi Window

Processor

connection

Fig. 1

Fig. 2

2

PREFACE

< DZ780/DW750/DX820 >

f

The specifications of the projector are as follows.

100 V - 240 V ~  (100 V - 240 V 
alternating current), 50 Hz/60 Hz (9.0 A - 
4.0 A)

110 V ~  (110 V alternating current), 60 Hz 
(8.0 A)

790 W

785 W

Approx. 0.3 W when [STANDBY MODE] is 
set to [ECO]

Approx. 0.2 W when [STANDBY MODE] is 
set to [ECO]

Approx. 3 W when [STANDBY MODE] is set to [NORMAL]

17 mm (0.67") (aspect ratio 16:10)

16.5 mm (0.65") (aspect ratio 16:10)

17.8 mm (0.7") (aspect ratio 4:3)

1-unit DLP chip, DLP type

2 304 000 pixels (1 920 x 1 200 dots)

1 024 000 pixels (1 280 x 800 dots)

786 432 pixels (1 024 x 768 dots)

1.7 - 2.4:1

1.8 - 2.5:1

F = 1.7 - 1.9
f = 25.6 mm - 35.7 mm

310 W UHM lamp x 2

7 000 lm (ANSI)

8 200 lm (ANSI)

3 000:1

2 400:1

7 standards (NTSC/NTSC4.43/PAL/PAL-N/PAL-M/SECAM/PAL60)

1.27 m (50") to 15.24 m (600")

16:10

4:3

[FRONT/CEILING], [FRONT/FLOOR], [REAR/CEILING], [REAR/FLOOR]

3.0 m (118-1/8")

Molded plastic

White

Black

*1  The lens for PT-DZ780L series, PT-DW750L series, and PT-DX820L series is sold separately.
*2  Value is for the supplied standard zoom lens. The value varies depending on the lens.
*3  Measurement, measuring conditions and method of notation all comply with ISO21118 international standards.
*4  When the lens ET-DLE055 is used, the maximum size is 5.08 m (200"). When the lens ET-DLE030 is used, the maximum size is 2.54 m (100") to 

8.89 m (350").

2

PREFACE

< DZ780/DW750/DX820 >

498 mm (19-19/32")

175 mm (6-7/8") (with legs at shortest position)

PT-DZ780, PT-DW750, PT-DX820 521 mm (20-1/2") (including standard zoom lens)

498 mm (19-19/32") (excluding lens mount cover and optional lens)

PT-DZ780, PT-DW750, PT-DX820 Approx. 17.8 k

] (39.3 lbs.)

*1

 (including standard zoom lens)

Approx. 17.0 k

] (37.5 lbs.)

*1

 (excluding lens mount cover and optional 

lens)

30 dB

0 °C (32 °F) to 45 °C (113 °F)

10 % to 80 % (no condensation)

DC 3 V (AAA/R03 battery x 2)

Within approx. 30 m (98'5") (when operated directly in front of signal receiver)

102 

] (3.6 ozs.) (including batteries)

Width: 48 mm (1-7/8"), Height: 145 mm (5-23/32"), Depth: 27 mm (1-1/16")

*1  Average value. Weight varies for each product.
*2  Measurement, measuring conditions and method of notation all comply with ISO21118 international standards.
*3  When using the projector at elevations lower than 2 700 m (8 858') above sea level, and the operating environment temperature becomes 35 °C 

(95 °F) or higher, the light output may be reduced to protect the projector. When using the projector at elevations between 2 700 m (8 858') and 
4 200 m (13 780'), and the operating environment temperature becomes 25 °C (77 °F) or higher, the light output may be reduced to protect the 
projector.

3

PREFACE

< DZ780/DW750/DX820 >

f

Refer to Operating Instructions “List of compatible signals”  for the types of video signals that can be used with the projector.

Horizontal: 15.73 kHz, Vertical: 59.94 Hz; Horizontal: 15.63 kHz, Vertical: 50 Hz

Horizontal: 15 kHz to 100 kHz, Vertical: 24 Hz to 120 Hz
PIAS (Panasonic Intelligent Auto Scanning) system

 

f Dot clock frequency: 162 MHz or less

 

f 525i (480i)

Horizontal: 15.73 kHz, Vertical: 59.94 Hz

 

f 525p (480p)

Horizontal: 31.47 kHz, Vertical: 59.94 Hz

 

f 750 (720)/60p

Horizontal: 45 kHz, Vertical: 60 Hz

 

f 1125 (1035)/60i

Horizontal: 33.75 kHz, Vertical: 60 Hz

 

f 1125 (1080)/50i

Horizontal: 28.13 kHz, Vertical: 50 Hz

 

f 1125 (1080)/24sF

Horizontal: 27 kHz, Vertical: 48 Hz

 

f 1125 (1080)/30p

Horizontal: 33.75 kHz, Vertical: 30 Hz

 

f 1125 (1080)/50p

Horizontal: 56.25 kHz, Vertical: 50 Hz

 

f 625i (576i)

Horizontal: 15.63 kHz, Vertical: 50 Hz

 

f 625p (576p)

Horizontal: 31.25 kHz, Vertical: 50 Hz

 

f 750 (720)/50p

Horizontal: 37.5 kHz, Vertical: 50 Hz

 

f 1125 (1080)/60i

Horizontal: 33.75 kHz, Vertical: 60 Hz

 

f 1125 (1080)/24p

Horizontal: 27 kHz, Vertical: 24 Hz

 

f 1125 (1080)/25p

Horizontal: 28.13 kHz, Vertical: 25 Hz

 

f 1125 (1080)/60p

Horizontal: 67.5 kHz, Vertical: 60 Hz

 

f The SYNC/HD and VD terminals do not support 3 value SYNC.

525i (480i)

*1

, 625i (576i)

*1

, 525p (480p), 625p (576p), 750 (720)/60p,  

750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p,  
1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p,  
1125 (1080)/60p, 1125 (1080)/50p

 

f Displayable resolution: VGA to WUXGA (non-interlaced)

 

f Dot clock frequency: 25 MHz to 162 MHz

525i (480i)

*1

, 625i (576i)

*1

, 525p (480p), 625p (576p), 750 (720)/60p,  

750 (720)/50p, 1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p,  
1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p,  
1125 (1080)/60p, 1125 (1080)/50p

 

f Displayable resolution: VGA to WUXGA (non-interlaced)

 

f Dot clock frequency: 25 MHz to 162 MHz

For SDI signal
(Only for PT-DZ780)

SMPTE ST 259 compliant
YC

B

C

R

 4:2:2 10-bit

480i, 576i

SMPTE ST 292 compliant
YP

B

P

R

 4:2:2 10-bit

720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 
1080/24p, 1080/24sF, 1080/30p

SMPTE ST 424 compliant
YP

B

P

R

 4:2:2 10-bit

1080/50p, 1080/60p
RGB 4:4:4 12-bit/10-bit
1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p

*1  Pixel-Repetition signal (dot clock frequency 27.0 MHz) only

 

f DIGITAL LINK input compatible signal is the same as HDMI input compatible signal.

4