DOWNLOAD Panasonic PT-DZ780 / PT-DW750 / PT-DX820 / PT-DZ780BE / PT-DZ780LBE / PT-DZ780LWE / PT-DZ780WE / PT-DW750BE / PT-DX820BE / PT-DX820LBE (serv.man2) Service Manual ↓ Size: 59.12 MB | Pages: 104 in PDF or view online for FREE

SECTION 1  SERVICE  INFORMATION

< DZ780/DW750/DX820 >

[DIGITAL LINK MODE]

[AUTO]

[DIGITAL LINK SETUP]

―

[DIGITAL LINK STATUS]

―

[NETWORK SETUP]

―

[NETWORK CONTROL]

―

[NETWORK STATUS]

―

[DIGITAL LINK MENU]

―

[Art-Net SETUP]

[OFF]

 

f Some items may not be adjusted or used for certain signal formats to be input to the projector.

The menu items that cannot be adjusted or used are shown in black characters, and they cannot be selected.

 

f Sub-menu items and factory default settings vary depending on the selected input terminal.

INF - 8

SECTION 1  SERVICE  INFORMATION

< DZ780/DW750/DX820 >

This projector has Service Mode in addition to standard on-screen menus (User Mode).
This mode enables some menu settings for the service operation.

1. Press the MENU button on the control panel of the projector or on the remote controller.
2. Select the sub menu [service password] of the main menu [projector setup] and press the ENTER button.
3. Input the password "1565" by remote control and press the ENTER button.

4. Press the MENU button. Service mode menu will be displayed.

1. Press the MENU button on the control panel of the projector or on the remote controller.
2. Select the sub menu [service password] of the main menu [projector setup] and press the ENTER button.
3. Input the password "0000" by remote control and press the ENTER button.

4. Press the MENU button. User mode menu will be displayed.
[ Note ] "Service mode" will be canceled even when the power is turned off.

[EXTRA OPTION] is added to bottom in the main menu.

1. DYNAMIC GAMMA MODE

f

Setting of the DYNAMIC GAMMA operation. 

- ON : Enable the Dynamic gamma function. (Default setting)
- OFF : Disable the Dynamic gamma function.

2. 3DCMS

f

Setting of the 3D Color Management System operation.

- ON : Enable the 3D Color Management system function. (Default setting)
- OFF : Disable the 3D Color Management system function.

[ Note ] Function specification varies according to a version of the main microcomputer software.

INF - 9

SECTION 1  SERVICE  INFORMATION

< DZ780/DW750/DX820 >

3. SELF CHECK

f

Self-diagnosing information displays.

 SELF CHECK

1/2

(1)-

 MAIN         : 1.00

(2)-

 SUB          : 1.00

(3)-

 DIGITAL LINK : 1.30.20.5

(4)-

 DDP          : 00.0400.00 

(5)-

 BALLAST      : 1.00 / 1.00

(6)-

 EMULATE      : DEFAULT

(7)-

 OK  AIR TEMP 123/456   OK  DMD TEMP 123/456

(8)-

 OK  OUT TEMP 123/456   OK  AIR FLOW 123/456/789

(9)-

 OK  LAMP1 12345H 30M ON

(10)-

 OK  LAMP2 12345H 30M ON

(11)-

 OK  FAN 1111 1111 1

(12)-

 OK  PHOTO  12345.6     OK ATM 1234/567

(13)-

 OK  ANGLE H -12.34/V +12.34

(14)-

 OK  SHUTTER 12345 [   0]

(1) Main microprocessor software version
(2) Sub microprocessor software version
(3) DIGITAL LINK microprocessor software version
(4) Formatter microprocessor software version
(5) Ballast microprocessor software version
(6) State of the EMULATE setting
(7) Intake air temperature check (Celsius/Fahrenheit), DMD temperature check (Celsius/Fahrenheit)
(8) Exhaust air temperature check (Celsius/Fahrenheit), 

Air flow sensor check (Sensor detected value/AD conversion value/Correction value)

(9) LAMP1 check (Cumulative usage time/ON-OFF)

(10) LAMP2 check (Cumulative usage time/ON-OFF)
(11) Fan control check (1: normal / 0:stop)

  OK   FAN

(12) Luminance sensor check (Sensor detected value), 

Atmospheric pressure sensor check (Sensor detected value/Temperature detected value)

(13) Angle sensor check (Horizontal angle / Vertical angle)
(14) Shutter control check (Opening and shutting number of times [Failed number of times])

f

Asia model dedicated status screen appears.

 SELF CHECK

2/2

 ASIA MODEL

(15)-

   MODEL

: YES

(16)-

   CONNECTION

: YES

(17)-

   VERSION

: 13.00.007

(18)-

   LEVEL

: -128/-128

(19)-

   UNLOCK

: NO

(20)-

   LIMIT COUNT

: 30/30

 1  1  1  1      1  1  1  1      1

DMD

LAMP1

LAMP2

EXHAUST1

EXHAUST2

CW

POWER

BALLAST

PUMP

* The "OK" font color will be red if the projector had shutdown due to abnormality last time.

INF - 10

SECTION 1  SERVICE  INFORMATION

< DZ780/DW750/DX820 >

(15) Model setting state

- YES : Set to the Asia model
- NO  : Set to the non Asia model

(16) Communication status of the WL-Module

- YES : Communication good
- NO  : Communication error (faulty or disconnected)

(17) Firmware version of IC on the WL-Module
(18) Usage environmental information

・

Applicable country Information / Non applicable country Information

(19) Functional restriction setting

- YES : Function restriction has been canceled
- NO  : Function restriction has been enabled

(20) Function restriction countdown

・

Counter at the time of communication error / Counter at the time of environmental error

・

Count is decreased when an error is detected.
AND become restricted with counter " 0 ". (Maximum 30)

4. CW INDEX

f

When replaced the color wheel, perform adjustment of color wheel rotational phase.

* Refer to [SECTION 3 Adjustments] for the procedure.

5. POWER OFF MESSAGE

f

Operation setting of shutter at standby operation.

- SHUTTER KEEP: When pushing the standby key while the shutter mode is on, the projector keeps the shutter

mode on and sets into standby mode.

- SHUTTER OPEN: When pushing the standby key while the shutter mode is on, the projector opens the shutter

and displays the "Power OFF confirmation message". (Default setting)

6. ERROR OSD

f

The screen display setting of the LAMP errors. (for projection from rear)

- ON: If the lamp error occurrence, a message will appear on the screen.
- OFF: Lamp error message does not appear on the screen. (Default setting)

7. MODEL

f

This setting is necessary when the A-P.C.Board is replaced.

* If you can copy EEPROM data from the old A-P.C.Board, this setting is unnecessary.
* This model setting is effective after power restart.

8. CLOG SENSOR CALIBRATION

f

This is to calibrate the clog sensor circuit.
This calibration is necessary when the A-P.C.Board, EEPROM (IC3518) or M2-P.C.Board is replaced.

* Refer to [SECTION 3 Adjustments] for the procedure.

1. [PICTURE] menu

f

Will be added the following items by pressing the ENTER button at "PICTURE MODE".

1) [Ye MODULATE]

- ON : Enable the yellow color correction function.
- OFF : Disable the yellow color correction function. (default)

2) [DYNAMIC RGB BOOSTER]

- Adjust the image adaptive lamp modulation system effect manually.

[OFF, 1-7 step]

INF - 11