Panasonic PT-DZ570U / PT-DZ570E / PT-DW530U / PT-DW530E / PT-DX500U / PT-DX500E (serv.man8) Service Manual ▷ View online
<PT-DZ570U/PT-DW530U/PT-DX500U/PT-DZ570E/PT-DW530E/PT-DX500E>
3. Choose "Serial" in "Connection" and input the ID, Port, Baudrate, Parity , and click [Connection Check] button.
4. A result of the connection confirmation is displayed.
5. Choose Microprocessor to update, and click [load] button.
6. Appoint the microcomputer software that took in a computer beforehand, and click [Open] button.
"Check: NG" → Come back to item 3., and please
confirm whether setting is right.
confirm whether setting is right.
"Check: OK" → Click a [OK] button and advance next.
Note:
Update with RS232C interface is
only for Main and Sub
microprocessor.
Update with RS232C interface is
only for Main and Sub
microprocessor.
ADJ - 12
<PT-DZ570U/PT-DW530U/PT-DX500U/PT-DZ570E/PT-DW530E/PT-DX500E>
8. Click [OK] button and start update.
9. If completion and a message are displayed, click [OK] button.
10. Click ［EXIT］button, and please be finished.
7. When load of the microcomputer software is completed, a checkmark and a path are displayed and a version of the
microcomputer software that load is displayed by "Version Information".
Confirm it is OK and press "Update".
microcomputer software that load is displayed by "Version Information".
Confirm it is OK and press "Update".
Reboot Projector, and please confirm whether the version of the Microprocessor Software is updated definitely, with sub menu "
STATUS" of the main menu " PROJECTOR SETUP" .
STATUS" of the main menu " PROJECTOR SETUP" .
While update it, Lamp1/2-indicator indicates as follows.
* Main → Red LED blinks.
* Sub → Green LED flashes.
* Main → Red LED blinks.
* Sub → Green LED flashes.
Note:
If you delete the check mark,
the software is not updated.
If you delete the check mark,
the software is not updated.
Note:
The update for same version software is
skipped..
The update for same version software is
skipped..
ADJ - 13
<PT-DZ570U/PT-DW530U/PT-DX500U/PT-DZ570E/PT-DW530E/PT-DX500E>
■
Notes
1. Resistor
All the resistors are carbon 1/4W resistors, unless marked as follows.
The unit of resistance is an OHM [Ω] (K=1 000 M=1 000000).
The unit of resistance is an OHM [Ω] (K=1 000 M=1 000000).
: Nonflammable
: Metal Oxide
: Solid
: Metal Film
: Wire Wound
: Fuse
2. Capacitor
: Temperature Compensation
: Electrolytic
: Polyester
: Bipolar
: Metalized Polyester
: Dipped Tantalum
1. Block Diagram ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
DIA-2
: Polypropylene
: Z-Type
1.1. Signal Processing
3. Coil
1.2. Power / Ballast Blockdiagram
The unit of inductance is a H, unless otherwise noted.
4. Test Point
2. Interconnection Block Diagram ・・・・・・・・・・・・・・・・・・・・・・・・
DIA-6
: Test Point
5. HOT and COLD indications
3. Schematic Diagram・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
DIA-7
3.1. A-P.C.Board
3.2. J-P.C.Board
6. This schematic diagram is the latest at the time of printing and the subject to change without notice.
3.3. S-P.C.Board
■
Precautions
4. Circuit Boards Diagram ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・
DIA-10
1. NEVER touch the HOT part or the HOT and COLD parts at the same time, or you may get an electric shock.
4.1. A-P.C.Board
2. NEVER short-circuit the HOT and COLD circuits, or the fuse may blow and the parts may break.
4.2. J-P.C.Board / S-P.C.Board
4. MAKE SURE to unplug the power cord from the power outlet before removing the chassis.
The power circuit board contains a circuit area using a separate power supply to isolate the ground connection.
The circuit is defined by HOT and COLD indications in the schematic diagram. Take the precautions below:
The circuit is defined by HOT and COLD indications in the schematic diagram. Take the precautions below:
3. NEVER connect an instrument such oscilloscope to the HOT and COLD circuit simultaneously, or the fuse may blow.
Connect the ground of instruments to the ground of the circuit being measured.
Connect the ground of instruments to the ground of the circuit being measured.
CONTENTS
SECTION 4
< Schematic Diagram >
Components identified by the intemational symbol have special characteristics important for safety.
When replacing any of these components, use only the manufacturer's specified ones.
When replacing any of these components, use only the manufacturer's specified ones.
PT-DZ570U / DZ570E
PT-DW530U / DW530E
PT-DX500U / DX500E
Model No.
Important Safety Notice
F
E
D
C
A
4
3
2
1
DAI-2
8
7
6
5
9
B
1. 1 Signal Processing (1/3) < DZ570*/DW530* >
FM-P.C.Board
D-P.C.Board
E-P.C.Board
IC1017
ADC #2
with HDMI RxD
IC1055
ACD #1
with HDMI RxD
and
Audio Processor
RGB/YUV444/(YUV422) 10Bit *3.
RGB/YUV444/(YUV422) 10Bit *3.
IC1400
Risize
with CPU
and
Video Decorder
EEPROM
S- P.C.Board
IR
IC1412
FPGA
Net Work
(LAN）
S-Video
Video
RGB2
RGB1
IC3100
SUB CPU
34
A2
HDMI
LPF
IC1013
Analog SW
DVI
DDR2
SDRAM
IC1004
SW
IC1005
SW
EDID
SW
IC1001
IC1003
EEPROM
EDID
SW
IC1014
IC1016
H-Buffer
V-Buffer
IC1020
IC1002
RGB2
(G/Y)
RGB1
(G/Y)
Audio-IN(Analog)
Audio-OUT
Audio-IN(NT)
RJ-45
NT-Video
BtoB
Q1402、Q1403
LEVEL
SHIFT
IC1701
Audio-IN(Analog)
Audio-OUT(Analog)
REMOTE IN
2
2
Audio-MUTE
2
8
2
Audio-SEL
2
2
REMOTE_FR
1
/
/
/
/
/
/
/
/
33
33
26
／
/ 3
／
／
X1403
35.455MHz
VCXO
X1402
27.0MHz
DDR2
SDRAM
IC1409
IC1410
64M
Flash
Memory
512k
EEPROM
REAL TIME
CLOCK
X1401
AA_33SCL0
AA_33SDA0
ADC2_clock
IC1023
SW
ADC1_clock
AA_NT_TXD, AA_NT_RXD
24.576MHz
AA_33SCL2, AA_33SDA2
AA_33SCL1, AA_33SDA1
AA_33SCL3
AA_33SDA3
FFC
A7
L-P.C.Board
L11
EEPROM
L12
E1
A7
A3
Connect with Power Module
A4
+3.3V
+12V
LOW-STB3.3V
A6
O
N/
O
FF
SY
NC
UA
RT
T
XD
UA
RT
R
XD
NT_clock
AA_232C_IN_TXD, AA_232C_IN_RXD
IIC
AA_R8_TXD
AA_R8_RXD
AA_R8_RXD
AA_ARM_RESET
IC1423
A1
AZ_KEY1
AZ_KEY2
AZ_KEY3
AZ_KEY4
REMOTE_REAR
S1
A5
AZ_MAIN/STB
BtoB
LVDS Dual
FM_CWINDEX
AA_LAMPEN
AA_FM_RESET
AA_LAMPLITZ
AA_PWRGOOD2
AA_FM_33SCL_IN
AA_FM_33SDA_IN
AA_FM_33SCL_OUT
AA_FM_33SDA_OUT
AA_PWRGOOD2
AA_PWRGOOD
AA_PWRDOWN
4wire Serial
Config.
pixel_clock
RESET
freerun_clock
M1
P.C.Board
M1
A11
A10
A12
M1
P.C.Board
M1
M2
P.C.Board
M2
INPUT AIR
TEMP
EXT AIR
TEMP
AIR FLOW
SENSER
A13
DMD TEMP
AA_THERMO_DMD
AA_THERMO_FIL
AA_THERMO_OUTAIR
AA_THERMO_INAIR
AA_THERMO_FIL
AA_THERMO_OUTAIR
AA_THERMO_INAIR
Connect with Ballast Module
A3
1
BtoB
A15
FANSENSE1
AZ_FANCON1
A16
FANSENSE2
AZ_FANCON2
A17
FANSENSE3
AZ_FANCON3
A19
FANSENSE6
AZ_FANCON6
IC1805
FAN14V
AZ_FANEN
Q2821
AZ_FANEN2
Power Fan
Exhaust. Fan
Lamp Fan
DMD Fan
FAN14V
IC1414
Analog SW
IC1418
IC1416
IC1413
IC1415
IC3002
R
M
30
01
IC3004
IC3001
J-P.C.Board
AUDIO IN1
AUDIO IN2
SERIAL IN
AUDIO IN3
REMOTE IN
AUDIO OUT
J1
AUDIO
ANALOG
SW
RS232C
IR
W
L1
A3
0
PHY
Transceiver
WL-P.C.Board
NETWORK
CPU
PHY TRANSCEIVER BUS
（
To：IC1701）
MAIN CPU BUS
（
（
To：IC1400）
AUDIO BUS
（
（
To：IC1055）
64M FLASH-
MEMORY
1G DDR2-
SDRAM
IC2001
IC2005
IC2004
X2000
X2001
27MHz 32.768KHz
W
ire
le
ss
M
od
ule
Ad
op
te
r SL
O
T
JK2000
ET-WM200
Wireless Module Adopter
A2
0
D1
FM1
H-Buffer
V-Buffer
DLV
SENSOR
PC3600
RM3500
1. Block Diagram
Q3
P3-P4
!
!
!
!
A-P.C.Board
!
!
!
!
LAMP Unit
!
!
!
!
!
!
!
!
PT-DZ570U/PT-DW530U/PT-DX500U/PT-DZ570E/PT-DW530E/PT-DX500E
Click on the first or last page to see other PT-DZ570U / PT-DZ570E / PT-DW530U / PT-DW530E / PT-DX500U / PT-DX500E (serv.man8) service manuals if exist.