Panasonic PT-DZ13KU / PT-DZ13KE / PT-DZ13KT / PT-DS12KU / PT-DS12KE / PT-DW11KU / PT-DW11KE / PT-DZ10KU / PT-DZ10KE (serv.man2) Service Manual ▷ View online
INF - 9
3. Service Mode
This projector has Service Mode in addition to standard on-screen menus (User Mode).
This mode enables some menu settings for the service operation.
3. 1. Setting to Service Mode
1. Please push the main body or the menu (MENU) button of the wireless remote controller.
2. Choose a sub menu "service password" of the main menu "projector setup" and push the enter (ENTER) button.
3. Input the password "1565" by remote control and press the ENTER button.
4. Press the MENU button. "SERVICE MODE" (MAIN MENU) will be displayed.
3. 2. Resetting to User Mode
1. Please push the main body or the menu (MENU) button of the wireless remote controller.
2. Choose a sub menu "service password" of the main menu "projector setup" and push the enter (ENTER) button.
3. Input the password "0000" by remote control and press the ENTER button.
4. Press the MENU button. "USER MODE" (MAIN MENU) will be displayed.
3. 3. Functions of Service Mode
* Function varies according to a version of the main microcomputer software.
3. 3. 1. EXTRA OPTION
"EXTRA OPTION" is added to the bottom of the main menu.
1. LIGHT OUTPUT
Adjusts brightness with Dynamic Iris. It darkens as the value becomes small.
2. MAX IRIS LEVEL
Adjustment the maximum diaphragm quantity of the Dynamic iris. Please do not usually change setting.
When changed an iris unit or a DMD block, please adjust it according to Clause 1 of SECTION 3 (Adjustments).
3. DYNAMIC GAMMA MODE
Sets ON (Valid) / OFF (Invalid) of Dynamic gamma. (Default : ON)
4. 3DCMS
Sets ON (Valid) / OFF (Invalid) of 3D Color Management system. (Default : ON)
INF - 10
5. SELF CHECK
Self-diagnosing information Displays.
SELF CHECK
①-
MAI N : 1. 00
②-
SUB : 1. 00
③-
NT : 1. 00 / 1. 00
④-
BALLAST : 100 / 100
⑤-
OK AI R TEMP 123/456
⑥-
OK DMD TEMP 123/456
⑦-
OK OUT TEMP 123/456
⑧-
OK AI R FLOW 123/456/789
⑨-
OK LAMP1 1234H 30M ON
⑩-
OK LAMP2 5678H 30M ON
⑪-
OK FAN 1111 1111 1111 11
⑫-
OK PHOTO SENSOR Y 12345. 6
⑬-
OK ANGLE SENSOR H -12. 34/V 0. 26
⑭-
OK I RI S
* If any error occurs, font of "OK" becomes red.
①- Main microprocessor Software Version
②- Sub microprocessor Software Version
③- Network microprocessor Software Version (rootfs/kernel)
④- Ballast microprocessor Software Version
⑤- Intake air temperature check (Celsius/Fahrenheit)
⑥- DMD temperature check (Celsius/Fahrenheit)
⑦- Exhaust air temperature check (Celsius/Fahrenheit)
⑧- Airflow sensor check (Sensor value/AD conversion value/Correction value)
⑨- LAMP1 check (Cumulative usage time/ON-OFF)
⑩- LAMP2 check (Cumulative usage time/ON-OFF)
⑪- Fan check (1: normal /0:stop)
②- Sub microprocessor Software Version
③- Network microprocessor Software Version (rootfs/kernel)
④- Ballast microprocessor Software Version
⑤- Intake air temperature check (Celsius/Fahrenheit)
⑥- DMD temperature check (Celsius/Fahrenheit)
⑦- Exhaust air temperature check (Celsius/Fahrenheit)
⑧- Airflow sensor check (Sensor value/AD conversion value/Correction value)
⑨- LAMP1 check (Cumulative usage time/ON-OFF)
⑩- LAMP2 check (Cumulative usage time/ON-OFF)
⑪- Fan check (1: normal /0:stop)
OK FAN
⑫- Brightness sensor check
⑬- Angle sensor check
⑭- Iris check
⑬- Angle sensor check
⑭- Iris check
6. POWER OFF MESSAGE
Setting of the shutter function with standby operation
- SHUTTER KEEP: When push the standby key with shutter ON, keep the shutter mode.
- SHUTTER OPEN: When push the standby key with shutter ON, open the shutter and display
the "Power OFF confirmation message". (Default setting)
7. ERROR OSD
When do not watch the error instructions LED of the lamp by a back projection,
the errors of the lamp can be displayed in the OSD.
- ON: "Lamp error message" is displayed on OSD.
- OFF: Does not display the "Lamp error message" in OSD.
8. CONVERGENCE
When the ingredient of each R/G/B color deviation, revise it electrically.
Specifically, please refer to Clause 1 of SECTION 3 (adjustments).
9. MODEL
Set this when the A-P.C.Board is replaced.
* If you can copy EEPROM data from the old A-P.C.Board, this setting is unnecessary.
* This model setting is changed after power restart.
1 1 1 1
1 1 1 1
1 1 1 1
1 1
1
E
x
haus
t (
R
)
E
x
haus
t (
C
)
E
x
haus
t (
L)
Int
ak
e 1
Int
ak
e 2
Lam
p 1
Lam
p 2
P
ow
er
B
al
las
t
C
-m
irro
r
D
M
D
ex
haus
t
C
ol
or
pr
is
m
DM
D
1
DM
D
2
INF - 11
10. CLOG SENSOR CALIBRATION
Calibrate the clogging sensor circuit.
* Execute this after EEPROM(IC3509/IC3518)/A-P.C.Board or clogging sensor (M2-P.C.Board) is replaced.
* Please refer to Clause 1 of SECTION 3 (Adjustments) for the procedure.
3. 3. 2. Additional function of each menu
1. [PICTURE] menu
「AI WINDOW」 is added to the setting of the sub menu "dynamic iris".
- Sets the APL detection area.
2. [POSITION] menu
「DVI EQUALIZER」 is added to a sub menu.
- When noise contamination to DVI input caused by long cable or external device, set this item so that
the noise decreases.
3. [DISPLAY OPTION] menu
The following items are added to setting of sub menu "SDI IN".
「XYZ TO RGB SETTING」
「XYZ TO RGB SETTING」
- FACTORY SETTING: Uses the value of FACTORY Yxy conversion factor to the original data of XYZ → RGB.
- MEASURED: Uses the value of MEASURED Yxy conversion factor to the original data of XYZ → RGB.
- REC709: Uses the value of REC709 Yxy conversion factor to the original data of XYZ → RGB.
- DCI P3: Uses the value of DCI P3 Yxy conversion factor to the original data of XYZ → RGB.
「XYZ TEST PATTERN」
「XYZ TEST PATTERN」
- WHITE:10%~100%
- DARK GRAY:1~10
- COLOR:Red/Green/Blue/Cyan/Magenta/Yellow 1~2
4. [PROJECTOR SETUP] menu
The following items are added to an indication screen of the sub menu "STATUS ".
1) Page 2
- FPGA VERSION
FPGA version (FOGA1/FPGA2/FPGA3)
- BALLAST VERSION
Ballast software version
2) Page 4
- VERTICAL TILT
Vertical angle
- HORIZONTAL TILT
Horizontal angle
3) Page 6
- MAIN VERSION
Main Microcomputer Software Version
- FPGA VERSION
FPGA version (FOGA1/FPGA2/FPGA3)
- BMP VER.
Version of Bitmap data
- ENG VER. ~ JPN VER.
Version of the each font data (English/Russian/Korean/Chinese/Japanese)
4) Page 7
- FM R/FM G/FM B VERSION Version of the each Formatter Software Version
(Configuration/Main Application/Sequence/De-Gamma)
5) Page 8
- TEMP(℃)
Intake air temperature / Exhaust air temperature / Optical module temperature
- P.SENSOR
Brightness Sensor value
- VOLT
Voltage of LAMP1/LAMP2
- AIR FLOW
Sensor value / AD conversion value, Sensor Correction value/ AD conversion value
- FAN MODE
FAN control mode (LOW/MID/HIGH)
- CLOG
Fan rev up state due to clogging of air filter
(+0:NONE, +1:LEVEL1, +2:LEVEL2, +3:LEVEL3, Life extension:LIFE)
- R-EXST
Exhaust (R) fan status [Rotational speed]
- C-EXST
Exhaust (C) fan status [Rotational speed]
- L-EXST
Exhaust (L) fan status [Rotational speed]
- INTAKE1
Intake1 fan status [Rotational speed]
- INTAKE2
Intake2 fan status [Rotational speed]
INF - 12
- LAMP1
Lamp1 fan status [Rotational speed]
- LAMP2
Lamp2 fan status [Rotational speed]
- P-UNIT
Power fan status [Rotational speed]
- BALLAST
Ballast fan status [Rotational speed]
- C-MIRROR
Composition mirror fan status [Rotational speed]
- DMD-EXST
DMD exhaust fan status [Rotational speed]
- C-PRISM
Color prism fan status [Rotational speed]
- DMD1
DMD1 fan status [Rotational speed]
- DMD2
DMD2 fan status [Rotational speed]
6) Page 9
Information of SDI signal. (when information cannot show, "---" is displayed)
- MODE
Mode (「NO SIGNAL」,「SD-SDI」,「HD-SDI」,「3G-SDI」)
- TRANSPORT
Conversion method (「PROGRESSIVE」,「INTERLACED」)
- PICTURE
Picture information (「PROGRESSIVE」,「INTERLACED」)
- RATE
Rate information (「23.98」,「24」,「25」,「29.97」,「30」,「50」,「59.94」,「60」)
- SAMPLING
Sampling information
(「4:2:2 (YPBPR)」,「4:2:2 (YCBCR)」,「4:4:4 (YPBPR)」,「4:4:4 (YCBCR)」,
「4:4:4 (RGB)」,「4:4:4:4 (YPBPR+A)」,「4:4:4:4 (RGB+A)」,「4:4:4 (XYZ)」)
- BIT DEPTH
Bit depth (「8bit」,「10bit」,「12bit」)
7) Page 10~11
ON-OFF log of lamp 1 and lamp 2
5. [TEST PATTERN] menu
The following test patterns are added.
- Focus (background 70% Gray) pattern
- Checker pattern
- Inverted checker pattern
Click on the first or last page to see other PT-DZ13KU / PT-DZ13KE / PT-DZ13KT / PT-DS12KU / PT-DS12KE / PT-DW11KU / PT-DW11KE / PT-DZ10KU / PT-DZ10KE (serv.man2) service manuals if exist.