Panasonic DP-C262 / DP-C322 (serv.man2) Service Manual ▷ View online
125
APR 2005
Ver. 1.1
DP-C262/322
(41) Reinstall the Hopper Unit.
Note:
When reinstalling, make sure that the 2 projections
on the Hopper Unit are seated in the 2 holes firmly,
and at the same time, the supply cylinder is
properly positioned as illustrated.
on the Hopper Unit are seated in the 2 holes firmly,
and at the same time, the supply cylinder is
properly positioned as illustrated.
(42) Reinstall the WTB Lower Cover.
(43) Reinstall the Pipe Cover.
(44) Reinstall the Inner Cover.
(45) Remove the papers covering the Drum.
(46) Hook the Lever Arm.
(47) Reinstall the Drum Unit.
(48) Lock all the Drum Units by turning the Drum
(43) Reinstall the Pipe Cover.
(44) Reinstall the Inner Cover.
(45) Remove the papers covering the Drum.
(46) Hook the Lever Arm.
(47) Reinstall the Drum Unit.
(48) Lock all the Drum Units by turning the Drum
Release Knob clockwise.
(49) Remove the sheet of paper.
126
DP-C262/322
APR 2005
Ver. 1.1
(50) Turn the Toner Cartridge upside down as
illustrated, then reinstall the Toner Cartridge.
(51) Reinstall the Toner Waste Container.
<Resetting the PM Counters>
Note:
1. Do not close the Front Cover.
2. If replacing the Developer Unit, follow step (52).
3. If replacing only the Developer, skip to step (53).
2. If replacing the Developer Unit, follow step (52).
3. If replacing only the Developer, skip to step (53).
(52) Perform "F8-09 Deve. Unit Count".
(F7-02-40, 41, 42, 43 Deve. Unit Count, and F7-
02-45, 46, 47, 48 are also initialized by this
operation)
02-45, 46, 47, 48 are also initialized by this
operation)
(53) Perform "F8-11 Developer Count".
(F7-02-45, 46, 47, 48 are also initialized by this
operation)
operation)
(54) Plug the AC Power Cord.
(55) Turn the Main Power Switch on the Back and the
(55) Turn the Main Power Switch on the Back and the
Power Switch on the Left Side of the machine to
the ON position.
the ON position.
(56) Close the Front Cover.
127
APR 2005
Ver. 1.1
DP-C262/322
2.2.11. LSU
(1) Open the Front Cover.
(2) Pull out the 2nd Paper Tray.
(2) Pull out the 2nd Paper Tray.
(3) Remove 5 Screws (S6).
(4) Remove the Left Cover.
(4) Remove the Left Cover.
(5) Remove 1 Screw (Y45).
(6) Remove the Ground Harness.
(7) Remove 1 Screw (Y33).
(8) Remove the LSU Fan (4302).
(6) Remove the Ground Harness.
(7) Remove 1 Screw (Y33).
(8) Remove the LSU Fan (4302).
(9) Disconnect 3 Harnesses on the LSU PC Board.
128
DP-C262/322
APR 2005
Ver. 1.1
Important:
Before proceeding, make a note of the alignment
pointer position. If the LSU is not reinstalled at the
same position, the scanning quality will be
affected.
pointer position. If the LSU is not reinstalled at the
same position, the scanning quality will be
affected.
Note:
LSU and Serial Numbers are printed as illustrated.
(10) Remove 3 Screws (Y33).
(11) Remove the LSU (4303).
<Cleaning the LSU Aperture Glass>
Refer to the Operating Instructions (For Basic
Operations, Maintenance Section).
Operations, Maintenance Section).
