Panasonic DP-2310 / DP-3010 (serv.man4) Service Manual / Other ▷ View online
45
DP-2310/3010
APR 2003
Ver. 1.00
5. Perform the Service Mode F6-16 (ADU Side Adjust), to adjust the gap to be 5 mm.
6. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value.
7. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to
6. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value.
7. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to
standby.
2.8.4.
100% Read Adjustment
1. Place the Original Document on the Platen Scanner.
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
size. Empty or pull out all the remaining trays (including the bypass tray) to disable them.
3. Press the "FUNCTION”, “ORIGINAL SIZE (LEDGER/A3)" and “3” keys simultaneously in that order
to enter the Service Mode.
4. Perform the Service Mode F2 (Single Copy Test).
5. Check the Image size of the Copy and the Original as Portrait.
6. Perform the Service Mode F6-00 (Adj 100% Side-Side Read), to adjust the Side to Side to be the
5. Check the Image size of the Copy and the Original as Portrait.
6. Perform the Service Mode F6-00 (Adj 100% Side-Side Read), to adjust the Side to Side to be the
same.
7. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-)
value.
8. Perform the Service Mode F6-01 (Adj 100% Lead-Tail Read), to adjust the Top to End to be the
same.
9. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-)
value.
10. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to
standby.
Note:
This is the size adjustment and do not worry about the positioning.
2.8.5.
Original Registration & CCD Read Adjustments
1. Place the Original Document on the Platen Scanner.
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
size. Empty or pull out all the remaining trays (including the bypass tray) to disable them.
3. Press the "FUNCTION”, “ORIGINAL SIZE (LEDGER/A3)" and “3” keys simultaneously in that order
to enter the Service Mode.
4. Perform the Service Mode F2 (Single Copy Test).
5. Check the Image size of the Copy and the Original as Portrait.
6. Perform the Service Mode F6-03 (Original Registration), to adjust the Original Registration.
7. If the gap is smaller than the Original, input a (-) value. If bigger than the Original, input a (+) value.
8. Perform the Service Mode F6-53 (P Mode Image Density), to adjust the CCD Read for the side
5. Check the Image size of the Copy and the Original as Portrait.
6. Perform the Service Mode F6-03 (Original Registration), to adjust the Original Registration.
7. If the gap is smaller than the Original, input a (-) value. If bigger than the Original, input a (+) value.
8. Perform the Service Mode F6-53 (P Mode Image Density), to adjust the CCD Read for the side
position.
9. If the gap is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value.
10. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to
standby.
2.8.6.
ADF 100% Image 1-Sided Adjustment
1. Place the Original Document on the ADF.
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
size. Empty or pull out all the remaining trays (including the bypass tray) to disable them.
3. Press the "FUNCTION”, “ORIGINAL SIZE (LEDGER/A3)" and “3” keys simultaneously in that order
to enter the Service Mode.
4. Perform the Service Mode F2 (Single Copy Test).
5. Check the Image size of the Copy and the Original as Portrait.
6. Perform the Service Mode F6-93 (ADF 100% Image 1-Sided), to adjust the Side to Side to be the
5. Check the Image size of the Copy and the Original as Portrait.
6. Perform the Service Mode F6-93 (ADF 100% Image 1-Sided), to adjust the Side to Side to be the
same.
7. If the image is smaller than the Original, input a (+) value. If bigger than the Original, input a (-)
value.
8. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to
46
APR 2003
Ver. 1.00
DP-2310/3010
standby.
Note:
This is the size adjustment and do not worry about the positioning.
2.8.7.
ADF Original Read Edge & ADF Main Scan Adjustments
1. Place the Original Document on the ADF.
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
2. Insert Ledger or A3 size paper into the 1st tray and change the tray setting to the appropriate paper
size. Empty or pull out all the remaining trays (including the bypass tray) to disable them.
3. Press the "FUNCTION”, “ORIGINAL SIZE (LEDGER/A3)" and “3” keys simultaneously in that order
to enter the Service Mode.
4. Perform the Service Mode F2 (Single Copy Test).
5. Check the Image size of the Copy and the Original as Portrait.
6. Perform the Service Mode F6-91 (Original Read Edge ADF), to adjust the ADF Original Read Edge.
7. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value.
8. Perform the Service Mode F6-90 (ADF Read Main Scan Pos.), to adjust the ADF Main Scan for
5. Check the Image size of the Copy and the Original as Portrait.
6. Perform the Service Mode F6-91 (Original Read Edge ADF), to adjust the ADF Original Read Edge.
7. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value.
8. Perform the Service Mode F6-90 (ADF Read Main Scan Pos.), to adjust the ADF Main Scan for
Side position.
9. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value.
10. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to
standby.
2.9.
Calibrating the LCD
1. Turn the Main Power Switch on the Back of the machine to the OFF (O) position and leave the Power
Switch on the Left Side of the machine in the ON (I) position.
2. Ensure that the F-ROM Card with Firmware Update is not installed in the machine. If the Card is
installed in the machine, remove it.
3. Press and hold the “ENERGY SAVER “ and “FUNCTION” keys down simultaneously, then turn the
Main Power Switch on the Back of the machine to the ON (I) position and continue holding the keys for
approximately 30 seconds until the Display becomes stable.
The LCD Display starts blinking and shows a “+” on the upper left edge of the display.
Note:
approximately 30 seconds until the Display becomes stable.
The LCD Display starts blinking and shows a “+” on the upper left edge of the display.
Note:
If you do not hold the "ENERGY SAVER" and "FUNCTION" keys down long enough, the Display
may go OFF.
may go OFF.
4. Press the “+” on the upper left edge of the display, press the “+” on the lower right edge and press the
“+” on the center of the display. Then the display goes to stand-by.
Caution:
Caution:
Prevent any damage to the LCD Display by not pressing with Sharp Edged Objects such as a Ball
Point Pen, etc.
Point Pen, etc.
5. Reboot the machine by cycling the power. Turn the Main Power Switch on the Back of the machine to
the OFF (O) then ON (I) position.
47
DP-2310/3010
APR 2003
Ver. 1.00
3 Troubleshooting
3.1.
Error Codes (For Copier)
The self-diagnostic functions detect troubles in the important components of the copier.
When any trouble occurs, the copier stops.
When any trouble occurs, the copier stops.
3.1.1.
User Error Codes (U Code)
Note:
Uxx and a message will appear on the Panel Display.
User Error Codes (U Code) Table
Code
Item
Possible Cause(s)
U0
Key Counter
1. Card Key not installed.
2. Key Counter Harness disconnected.
3. Department Code not assigned.
2. Key Counter Harness disconnected.
3. Department Code not assigned.
U1
Close Front Cover
1. Front Cover open.
2. Front Cover Sensor disconnected.
3. Front Cover Sensor defective.
4. LVPS connector disconnected.
5. LVPS defective.
6. SPC PCB connector disconnected.
7. SPC PCB defective.
2. Front Cover Sensor disconnected.
3. Front Cover Sensor defective.
4. LVPS connector disconnected.
5. LVPS defective.
6. SPC PCB connector disconnected.
7. SPC PCB defective.
U4
Close Finisher
1. Finisher open.
2. Paper in the output bin.
3. Stapler empty.
4. LVPS connector disconnected.
5. LVPS defective.
6. SPC PCB connector disconnected.
7. SPC PCB defective.
2. Paper in the output bin.
3. Stapler empty.
4. LVPS connector disconnected.
5. LVPS defective.
6. SPC PCB connector disconnected.
7. SPC PCB defective.
U6
Close Right Cover
1. Right Cover open.
2. Right Cover Sensor disconnected.
3. Right Cover Sensor defective.
4. LVPS connector disconnected.
5. LVPS defective.
6. SPC PCB connector disconnected.
7. SPC PCB defective.
2. Right Cover Sensor disconnected.
3. Right Cover Sensor defective.
4. LVPS connector disconnected.
5. LVPS defective.
6. SPC PCB connector disconnected.
7. SPC PCB defective.
U7
Close Feed Cover
1. Feed Cover open.
2. Feeder Unit incorrectly installed.
3. Feeder Unit connector disconnected.
4. Feeder Unit Sensor disconnected.
5. Feeder Unit Sensor defective.
6. LVPS connector disconnected.
7. LVPS defective.
8. CST2/CST3 PCB connector disconnected.
9. CST2/CST3 PCB defective.
2. Feeder Unit incorrectly installed.
3. Feeder Unit connector disconnected.
4. Feeder Unit Sensor disconnected.
5. Feeder Unit Sensor defective.
6. LVPS connector disconnected.
7. LVPS defective.
8. CST2/CST3 PCB connector disconnected.
9. CST2/CST3 PCB defective.
U8
Close Paper Transport Unit
1. Paper Transport Unit open.
2. Paper Transport Unit Sensor disconnected.
3. LVPS connector disconnected.
4. LVPS defective.
5. SPC PCB connector disconnected.
6. SPC PCB defective.
2. Paper Transport Unit Sensor disconnected.
3. LVPS connector disconnected.
4. LVPS defective.
5. SPC PCB connector disconnected.
6. SPC PCB defective.
U11
Remove Paper in Finisher
1. Paper in the Finisher.
2. Finisher Paper Exit Sensor defective.
2. Finisher Paper Exit Sensor defective.
48
APR 2003
Ver. 1.00
DP-2310/3010
U12
Close Finisher Staple Cover
/ Upper Cover
/ Upper Cover
1. Finisher Staple Cover open.
2. Finisher Staple Cover Sensor disconnected.
3. Finisher Staple Cover Sensor defective.
2. Finisher Staple Cover Sensor disconnected.
3. Finisher Staple Cover Sensor defective.
U13
Add Toner
1. Toner Bottle incorrectly installed.
2. Low Toner.
3. Toner Sensor disconnected.
4. Toner Sensor defective.
5. SPC PCB connector disconnected.
6. SPC PCB defective.
2. Low Toner.
3. Toner Sensor disconnected.
4. Toner Sensor defective.
5. SPC PCB connector disconnected.
6. SPC PCB defective.
U14
Replace Toner Waste
Container
Container
1. Toner Waste Container full.
(See Sect. 2.5.4.)
U15
No Toner Waste Container
1. Toner Waste Container not installed.
2. Toner Waste Container Sensor disconnected.
3. Toner Waste Container Sensor defective.
2. Toner Waste Container Sensor disconnected.
3. Toner Waste Container Sensor defective.
U16
No Developer Unit
1. Developer Unit not installed.
U18
Total Copy Limit Over
1. Department Copy Counter full.
U20
Close ADF Cover
1. ADF Cover open.
2. ADF not installed correctly.
3. ADF Cover Sensor disconnected.
4. ADF Cover Sensor defective.
5. LVPS connector disconnected.
6. LVPS defective.
2. ADF not installed correctly.
3. ADF Cover Sensor disconnected.
4. ADF Cover Sensor defective.
5. LVPS connector disconnected.
6. LVPS defective.
U21
Close ADF
1. ADF and ADF Cover open.
2. ADF Sensor disconnected.
3. ADF Sensor defective.
2. ADF Sensor disconnected.
3. ADF Sensor defective.
U22
Close ADF Exit Cover
1. ADF Exit Cover open.
2. ADF not installed correctly.
3. ADF Exit Cover Sensor disconnected.
4. ADF Exit Cover Sensor defective.
5. LVPS connector disconnected.
6. LVPS defective.
2. ADF not installed correctly.
3. ADF Exit Cover Sensor disconnected.
4. ADF Exit Cover Sensor defective.
5. LVPS connector disconnected.
6. LVPS defective.
U25
Shake Toner Bottle
1. Toner blocked in the Toner Bottle.
U90
Replace Battery
1. Internal battery requires replacement.
User Error Codes (U Code) Table
Code
Item
Possible Cause(s)
Click on the first or last page to see other DP-2310 / DP-3010 (serv.man4) service manuals if exist.