Panasonic DP-1510P / DP-1810P Service Manual ▷ View online
49
(27) Disconnect the Harnesses (1229, 1856) on the
LPC3 PC Board.
(28) Release the Harness (1818) from the Clamp.
(29) Disconnect the Harness (1818) on the Drive
(29) Disconnect the Harness (1818) on the Drive
Motor Assembly.
(30) 4 Screws (19).
(31) Remove the Drive Unit.
(31) Remove the Drive Unit.
Caution:
Do not remove the Gears from the Drive Unit.
If dis-assembled or the Alignment is necessary, be
careful to assemble the Gears by following steps.
If dis-assembled or the Alignment is necessary, be
careful to assemble the Gears by following steps.
<Toner Bottle Drive Gear Adjustment>
(1) Remove 2 Snap Rings and 2 Gears as
illustrated.
(2) Align 2 Gear Holes with the Sensor.
(3) Align the Joint Gear to the Vertical Position as
(3) Align the Joint Gear to the Vertical Position as
illustrated.
(30)
(30)
(31)
(29)
(28)
(1)
(2)
Sensor
2 Holes
(3)
50
(4) Install the Gear and the Snap Ring.
(5) Install the other Gear and Snap Ring.
(5) Install the other Gear and Snap Ring.
(5)
(4)
51
2.2.10.
AC Inlet
(1) 1 Silver Screw (B1).
(2) Remove the Inlet Cover (751).
(3) 2 Screws (35).
(4) Disconnect 2 Harnesses (1828).
(5) Remove the AC Inlet Assembly.
(2) Remove the Inlet Cover (751).
(3) 2 Screws (35).
(4) Disconnect 2 Harnesses (1828).
(5) Remove the AC Inlet Assembly.
(6) Disconnect the Harness (1842).
(7) Remove the AC Inlet (807).
(7) Remove the AC Inlet (807).
(1)
(3)
(2)
(5)
(4)
(4)
(6)
(7)
52
2.2.11.
Fuser Unit
(1) Open the Right Cover (601) Assembly.
(2) 2 Screws (19).
(3) Remove the Front Connector Cover (714).
(4) Remove the Rear Connector Cover (713).
(2) 2 Screws (19).
(3) Remove the Front Connector Cover (714).
(4) Remove the Rear Connector Cover (713).
(5) 2 Screws (4N).
(6) Remove 2 Harnesses (1829).
(7) Remove 2 Harnesses (1813).
(8) Release 2 Harnesses (1829) from the Clamp.
(9) Remove the Fuser Unit.
(6) Remove 2 Harnesses (1829).
(7) Remove 2 Harnesses (1813).
(8) Release 2 Harnesses (1829) from the Clamp.
(9) Remove the Fuser Unit.
(10) 1 Screw (23).
(11) 1 Screw (19).
(12) Remove the Lamp Holder (925).
(13) 1 Screw (23). (Opposite side)
(13) 1 Screw (23). (Opposite side)
Note:
When re-installing the Lamp Holder (925), insert
the Lamp Holder’s Leg (A) into the Guide (B).
the Lamp Holder’s Leg (A) into the Guide (B).
(2)
(2)
(3)
(1)
(4)
(5)
(6)
(7)
(9)
(8)
(12)
(13)
(11)
(10)
(A)
(B)
Click on the first or last page to see other DP-1510P / DP-1810P service manuals if exist.