DOWNLOAD Panasonic TH-50PB2E Service Manual ↓ Size: 4.61 MB | Pages: 54 in PDF or view online for FREE

9

TH-50PB2E

220 - 240 V AC, 50/60 Hz

Power on

375 W

Stand-by condition

0.5 W

Power off condition

0.3 W

Drive method: AC type 50-inch, 16:9 aspect ratio

1,105 mm (W) 

× 622 mm (H) × 1,268 mm (diagonal)

(No. of pixels)

2,073,600 (1,920 (W) 

× 1,080 (H))   [5,760 × 1,080 dots]

Temperature

0 

°C - 40 °C

Humidity

20 % - 80 %

Colour System

NTSC, PAL, PAL60, SECAM, Modified NTSC

Scanning format

525 (480) / 60i 60p, 625 (575) / 50i 50p, 750 (720) / 60p 50p, 1125 (1080) / 
60i 60p 50i 50p 24p 25p 30p 24sF, 1250 (1080) / 50i

PC signals

VGA, SVGA, XGA, SXGA
UXGA ..... (compressed)
Horizontal scanning frequency 15 - 110 kHz
Vertical scanning frequency 48 - 120 Hz

AV IN

VIDEO

BNC

1.0 Vp-p (75-ohm)

AUDIO 1 IN Stereo mini jack (M3) 

× 1

0.5 Vrms, Shared with COMPONENT/RGB IN

HDMI

TYPE A Connector

COMPONENT / RGB IN

Y / G

BNC

with sync 1.0 Vp-p (75-ohm)

P

B

/C

B

/B

BNC

0.7 Vp-p (75-ohm)

P

R

/C

R

/R

BNC

0.7 Vp-p (75-ohm)

AUDIO 1 IN Stereo mini jack (M3) 

× 1

0.5 Vrms, Shared with VIDEO

DVI-D IN

DVI-D 24 Pin

Compliance with DVI Revision 1.0

Content Protection

Compatible with HDCP 1.1

AUDIO 2 IN Stereo mini jack (M3) 

× 1

0.5 Vrms, Shared with PC IN

PC IN

High-Density Mini D-sub 15 Pin

Y or G with sync 1.0 Vp-p (75-ohm)
Y or G without sync 0.7 Vp-p (75-ohm)
P

B

 / C

B

 / B:0.7 Vp-p (75-ohm)

P

R

 / C

R

 / R:0.7 Vp-p (75-ohm)

HD / VD:1.0 - 5.0 Vp-p (high impedance)

AUDIO 2 IN Stereo mini jack (M3) 

× 1

0.5 Vrms, Shared with DVI-D IN

SERIAL

External Control Terminal
D-sub 9 Pin

RS-232C compatible

PEN ADAPTER

For electronic pen adapter

MEMORY/(CHARGE)

For USB memory/electronic pen charging

CHARGE

For electronic pen charging

WIRELESS MODULE

for Wireless module (ET-WM200E)

LAN

RJ45 10BASE-T/100BASE-TX, compatible with PJLink

TM

EXT SP

6-ohm, 16 W [8 W + 8 W] (10 % THD)

Speakers

120 mm 

× 40 mm × 2 pcs

Audio Output

20 W [10 W + 10 W] (10 % THD)

Transmission system

2.4 GHz radio transmission

Usage temperature range

0 

°C - 40 °C

External dimensions (L 

× H)

201.2 mm 

× 21.3 mm

239.2 mm 

× 25.4 mm (with optical attachment)

Weight

Approx. 43 g
Approx. 55 g (with optical attachment)

Operable distance of remote 
pointer

In front: 5 m     At an angle of 45

° : 3 m

Battery

Lithium-ion polymer rechargeable battery
DC 3.7 V, 200 mAh
Operation time

*1

: Approx. 5 hours

Charging time

*1

: Approx. 4 hours

Remote Control Transmitter

N2QAYB000691

10

TH-50PB2E

Batteries

R6 (UM3) Size 

× 2

Clamper

TMME289 

× 1

Ferrite core

J0KG00000014 

× 2

× H × D)

1,210 mm 

× 724 mm × 89 mm 

approx. 34.0 kg net

• Design and specifications are subject to change without notice. Mass and dimensions shown are approximate.
• This equipment complies with the EMC standards listed below.

EN55022, EN55024, EN61000-3-2, EN61000-3-3.

• The charger complies with EN 55011 Group 2, Class B.

*1

 Operation time/charging time

• The battery deteriorates after repeated use, and the operation time eventually becomes short. The figures above are at shipping from the fac-

tory, and are not a guarantee of performance.

• Replacement / repair of the battery only is not supported.

11

TH-50PB2E

Press and hold the VOL down button / - button on the bottom side of the unit and press the RECALL button on the remote
control 3 times quickly within 2 second, this will place the unit into the CAT mode. 

1. Set the OFF timer except for [0] minute by OFF TIMER button.
(30 minutes, 60minutes, 90 minutes)
2. Set the volume level of sound to 0 by VOL down button / - button
3. Press the RECALL button more than 3 seconds.

To exit the CAT mode, access the ID mode and switch off the main power.

Select the IIC mode by Up/Down button on the remote control at the front page of CAT mode and then press the Action button on
the remote control.

Subject and item are mentioned on “IIC mode structure”.
To exit the IIC mode, press the R button on the remote control.

12

TH-50PB2E

Select the CD mode by Up/Down button on the remote control at the front page of CAT mode and then press the Mute button on
the remote control more than 3 seconds.

Memory data change

To exit the CD mode, press the R button on the remote control.

As for the serial number of A-module for repair, a dummy value is displayed.
* By the set for which A-module was exchanged, a serial number is displayed as [-----].

• This unit adds the history display (5 times) of power supply failure to the CD mode as PTCT.
• By the self check of a signal system, only one history is displayed (After a self check disappears). But PTCT displays 5 times of

histories (Abnormality of the latest 3 times, first time and second time after shipment) and after a self check does not disappear.
You can see a detailed history of power failure sometimes.

* About the display contents of PTCT
PTCT : The position of [05] is the first time after shipment.
PTCT : The position of [04] is the second time after shipment.
PTCT : The position of [03] is second from last time.
PTCT : The position of [02] is last time.
PTCT : The position of [01] is the latest.

In [Contents & Check point] of [6.1.2. Power LED Blinking timing chart], the two-digit following PTCT are displayed by a hexadeci-
mal number.

Blinking times

Contents & Check point Display contents

ex.1

5 times

PTCT 05 H 09

05

ex.2

9 times

PTCT 09 H 09

09