Panasonic TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E Service Manual ▷ View online
9.1. Driver Set-up
9.1.1. Item / Preparation
1. Set Aging pattern: 0 (Vset ajustment pattern) by IIC mode.
2. Set the picture controls as follows.
Picture menu: Standard
Picture: +25
Aspect: Full
Picture: +25
Aspect: Full
Caution
1. First perform Vsus adjustment.
2. Confirmation of Vscn voltage should be performed after
2. Confirmation of Vscn voltage should be performed after
confirmation of Vad adjustment.
When Vad=-105V, Voltage of Vscn is 40V ±4V.
When Vad=-105V, Voltage of Vscn is 40V ±4V.
9.1.2. Adjustments
Adjust driver section voltages. (Refer to the panel data on the
panel data label.)
Check or adjust the following voltages with the multimeter.
panel data label.)
Check or adjust the following voltages with the multimeter.
Name
Test Point
Voltage
Volume
Remarks
Vsus
TPVSUS
(SS)
(SS)
Vsus ± 2V
R628 (P)
*
Ve
TPVE (SS)
Ve ± 1V
VR6000 (SS)
*
Vset
TPVSET
(SC)
(SC)
330V ± 7V
Fixed
Vad
TPVAD (SC) -105V ± 1V
VR6600 (SC)
Vscn
TPVSCN
(SC)
(SC)
Vad+145V ±
4V
4V
Fixed
Vda
TPVDA (SS) 75V + 1V, -2V Fixed
PFC
C446 (+)(-)
396V ± 0.5V
R443 (P)
*See the Panel label.
9 Adjustment Procedure
33
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
9.2. Initialization Pulse Adjust
1. Set Aging pattern: 0 (Vset ajustment pattern) by IIC mode.
2. Set the picture controls as follows.
2. Set the picture controls as follows.
Picture menu: Standard
Picture: +25
Aspect: Full
Picture: +25
Aspect: Full
3. Connect Oscilloscope to TPSC1 (T2) and adjust VR6602 for 190±10µ Sec.
Test point
Volume
Level
T2
TPSC1 (SC)
VR6602 (SC)
190 ± 10µ Sec.
9.3. P.C.B. (Printed Circuit Board) exchange
9.3.1. Caution
1. To remove P.C.B., wait 1 minute after power was off for discharge from electrolysis capacitors.
9.3.2. Quick adjustment after P.C.B. exchange
Adjust the following voltages with the multimeter.
P.C.B.
Name
Test Point
Voltage
Volume
Remarks
P Board
Vsus
TPVSUS (SS)
Vsus ± 2V
R628 (P)
*
PFC
C446 (+) (-) (P)
396V ± 0.5V
R443 (P)
SC Board
Vad
TPVAD (SC)
-105V ± 1V
VR6600 (SC)
SS Board
Ve
TPVE (SS)
Ve ± 1V
VR6000 (SS)
*
D, DS, DN Board
White balance, Pedestal and Sub brightness for NTSC, PAL, HD, PC and 625i signals
DN Board
Set Market Select Number to correct destination by MS mode. (See chap. 10.1.4)
*See the Panel label.
Caution:
Caution:
Absolutely do not reduce Vsus voltage below Ve not to damage the P.C.B.
34
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
9.4. Adjustment Volume Location
9.4.1. TH-37PR10B/E
9.4.2. TH-42PR10B/E
35
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
9.5. Test Point Location
9.5.1. TH-37PR10B/E
9.5.2. TH-42PR10B/E
36
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
Click on the first or last page to see other TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E service manuals if exist.