Panasonic TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E Service Manual ▷ View online
19. Disconnect the connectors(SS23, SS34).
20. Remove the Flexible Cables from the connectors(SS53,
20. Remove the Flexible Cables from the connectors(SS53,
SS54, SS55, SS56).
21. Remove 6 screws ( ) and then remove SS-Board.
22. Remove 1 screw ( ) and then remove the Ferrite Core.
22. Remove 1 screw ( ) and then remove the Ferrite Core.
23. Remove the Flexible Cable from the connectors(C10, C20).
24. Remove 6 screws ( ).
25. Remove the 6 Spacers and Spacer Rings from the Plasma
Panel.
Caution:
· Please confirm the installation place of Spacer and
Spacer Ring when you exchange the Plasma Panel,
and install Spacer and Spacer Ring in an original
installation place after exchanging the Plasma
Panel.
and install Spacer and Spacer Ring in an original
installation place after exchanging the Plasma
Panel.
26. Lift up the bottom of Plasma Panel to the arrow1 direction.
27. Pull the Plasma Panel to the arrow2 direction and then
27. Pull the Plasma Panel to the arrow2 direction and then
remove the Plasma Panel.
17
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
7 Disassembly
TH-42PR10B/E
· To disassemble P.C.B., wait for 1 minute after power was
off for discharge from electrolysis capacitors.
· and
marks indicate screw positions.
7.1. Removal of Rear Cover
1. Remove screws (×6
, ×6
, ×14
, ×8
) and then
remove the Rear Cover.
7.2. Removal of Slot Block
1. Disconnect the connectors (DS1, DS4, DS6, DS7).
2. Remove 4 screws and then remove the Slot Block.
3. Disconnect the connectors(DS2, DS8, DS15).
2. Remove 4 screws and then remove the Slot Block.
3. Disconnect the connectors(DS2, DS8, DS15).
7.3. Removal of DS-Board
1. Remove the Slot Block.
(Refer to Removal of Slot Block)
2. Disconnect the connector(DS14).
3. The Slot Block is turned inside out.
4. Remove 6 screws and then remove the Slot Cover.
4. Remove 6 screws and then remove the Slot Cover.
5. Remove 6 screws and then remove DS-Board.
18
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
7.4. Removal of HX-Board
1. Remove the Slot Block.
(Refer to Removal of Slot Block)
2. Remove DS-Board.
(Refer to Removal of DS-Board)
3. Remove 2 screws and then remove the Slot Case.
4. Remove 4 Hexagonal-Head screws and 2 screws and then
remove HX-Board.
7.5. Removal of Speaker(L, R)
1. Connected terminal hook is pushed, and the speaker lead
in 4 places is pulled out.
2. Remove 8 screws and then remove the Speaker(L, R).
7.6. Removal of DN-Board
1. Disconnect the connector(DN6).
2. Remove the Flexible Cable from the connector(DN1).
3. Remove 4 screws and then remove DN-Board and the
2. Remove the Flexible Cable from the connector(DN1).
3. Remove 4 screws and then remove DN-Board and the
Fixed Plate.
Note:
A re-setup of the destination is performed by MS mode
after DN-Board exchange.
after DN-Board exchange.
19
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
7.7. Removal of P-Board
1. Disconnect the connectors(P2, P6, P7, P9, P11, P12, P25)
2. Remove 10 screws and then remove P-Board.
2. Remove 10 screws and then remove P-Board.
7.8. Removal of D-Board
1. Remove the Slot Block.
(Refer to Removal of Slot Block)
2. Disconnect the connectors(D5, D25)
3. Remove the Flexible Cables from the connectors (D20,
3. Remove the Flexible Cables from the connectors (D20,
D31, D32).
4. Remove 4 screws and then remove D-Board.
7.9. Removal of SU-Board and SD-
Board
1. Remove the Flexible Cables from the connectors(SU1,
SU2, SU3, SU4, SD1, SD2, SD3, SD4).
2. Remove 3 screws.
3. Disconnect the connectors(SU45, SD46).
4. Slide SU-Board and SD-Board to the left, remove SU-Board
4. Slide SU-Board and SD-Board to the left, remove SU-Board
and SD-Board from the connectors(SC41, SC42).
20
TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E
Click on the first or last page to see other TH-37PR10B / TH-37PR10E / TH-42PR10B / TH-42PR10E service manuals if exist.