Panasonic TH-103PF12E Service Manual ▷ View online
25
TH-103PF12E
9.2.5.
Removal of Rear Cover ( E )
1. Remove screws (
×25 ) and then remove the Rear
Cover ( E ).
Note: when fixing Rear Cover ( E )
• Firstly screw on 2 screws (1-2) in order.
9.2.6.
Removal of Rear Cover ( F )
1. Remove Eye Bolt Covers.
2. Remove screws (
×21 ) and then remove the Rear
Cover ( F ).
9.3.
Removal of Side Angle (L), (R)
1. Remove Side Angle (L), (R) beforehand when remove the
following Boards.
9.3.1.
Removal of Side Angle (L)
1. Remove 4 screws (A) of the Plate.
Board name
Side Angle
SU-Board
Side Angle (R)
SM-Board
Side Angle (R)
SD-Board
Side Angle (R)
SC-Board
Side Angle (R)
C1-Board (upper)
Side Angle (R)
C6-Board (lower)
Side Angle (R)
SS2-Board
Side Angle (L)
SS3-Board
Side Angle (L)
SS-Board
Side Angle (L)
C6-Board (upper)
Side Angle (L)
C1-Board (lower)
Side Angle (L)
26
TH-103PF12E
2. Remove 19 screws and then remove the Side Angle (L).
9.3.2.
Removal of Side Angle (R)
1. Disconnect the connectors (DS15, P34).
2. Remove 2 screws ( ).
3. Remove 2 screws ( ) and then slide the Side Power Unit
3. Remove 2 screws ( ) and then slide the Side Power Unit
upward.
4. Remove the Side Power Unit.
5. Remove 4 screws (B) of the Plate.
6. Remove 19 screws and then remove the Side Angle (R).
9.4.
Removal of HDE-Board
1. Remove 4 screws (C) and then remove the HDE Terminal
Block.
2. Remove 4 screws (D).
3. Remove 2 screws (E) and then remove HDE-Board.
3. Remove 2 screws (E) and then remove HDE-Board.
27
TH-103PF12E
9.5.
Removal of HL-Board
1. Remove 4 screws (F) and then remove the HL Terminal
Block.
2. Remove 4 screws (G).
3. Remove 2 screws (H) and then remove HL-Board.
3. Remove 2 screws (H) and then remove HL-Board.
9.6.
Removal of H5-Board
1. Remove 2 screws and then remove H5-Board Block.
2. Disconnect the connector (H51).
2. Disconnect the connector (H51).
3. Remove 2 screws (J).
4. Remove 1 screw (K) and then remove H5-Board.
4. Remove 1 screw (K) and then remove H5-Board.
Note: when fixing H5-Board
• Screw on 1 screw (K) firstly.
9.7.
Removal of DS-Board
1. Remove the HL Terminal Block and the HDE Terminal
Block.
(Refer to Removal of HL-Board and HDE-Board)
(Refer to Removal of HL-Board and HDE-Board)
2. Remove H5-Board Block.
(Refer to Removal of H5-Board)
3. Remove 6 screws and then remove the Slot Case.
28
TH-103PF12E
4. Disconnect the connector (DS14).
5. Remove 10 screws and then remove the Fixed Plate
5. Remove 10 screws and then remove the Fixed Plate
6. Disconnect the connectors (DS2, DS4, DS6, DS9, DS15).
7. Remove the flexible cables from the connectors(DS1,
7. Remove the flexible cables from the connectors(DS1,
DS3).
8. Remove 3 screws and then remove DS-Board.
9.8.
Removal of HX-Board
1. Remove the Slot Case.
(Refer to Removal of DS-Board)
2. Disconnect the connector (HX1).
3. Remove 4 Hexagonal-Head screws and 2 screws and
3. Remove 4 Hexagonal-Head screws and 2 screws and
then remove HX-Board.
9.9.
Removal of DN-Board
Check that no bright points appears by Ve Life adjustment
after both D and DN board exchange.
after both D and DN board exchange.
1. Disconnect the connectors (DN3, DN5, DN9).
2. Remove the flexible cables from the connectors (DN1,
2. Remove the flexible cables from the connectors (DN1,
DN2)
3. Remove 4 screws and then remove DN-Board.
Note:
A re-setup of the destination is performed by MS
mode after DN-Board exchange.
mode after DN-Board exchange.
Click on the first or last page to see other TH-103PF12E service manuals if exist.