Panasonic CF-19CDBAXVM Simplified Service Manual ▷ View online
9-28
Back side
Match to the edge of the Board.
0 to 1mm
0 to 1mm
Match to the Connector.
0 to 1 mm
0 to 1 mm
Fold back and attach it
Insulation Tape
0 0.5mm
DIMM Sheet
DIMM Sheet
Remove the DIMM and attach the Sheet.
Set the DIMM after attaching the Sheet.
Set the DIMM after attaching the Sheet.
Match to the silk
0 0.5mm
Match to the silk
0 0.5mm
Match to the silk
0 0.5mm
Match to the silk
9-29
n Assembly of Main Unit
DU PCB ASSY
Main PCB Ass’y
Insert it before setting
the Main Board.
the Main Board.
Audio FPC Ass’y
Apply the lubricant (sub material) on the
HDD Connector for about 1 second.
(Note for spraying around when applying.)
HDD Connector for about 1 second.
(Note for spraying around when applying.)
Audio FPC Ass’y
Avoid running the Cable
over the Connector.
over the Connector.
Insert the Bastaraid between
the LAN/MODEM Connectors.
the LAN/MODEM Connectors.
0 1mm
Safety critical componentInsert
and then lock.
and then lock.
Audio FPC
Tape
Screw
Screw
Screw
Screw
Screw
Screw
Screw
Screw
Screw
Screw
Thermal Sheet
Wireless Module
Lengthwise
Fold back
Stiffening Plate Side
Center of module
to the notch
to the notch
Insert and then lock
Details of the LAN/MODEM
Insert and then lock.
Connect
Round to make the brown side
outside and insert the notch.
outside and insert the notch.
Attach it on the
center of the
FPC.
3mm
center of the
FPC.
3mm
Important Parts
for Safety
for Safety
SD PCB Ass’y
DIMM HOLDER Ass’y
Ensure that the knob is fit to SW when setting.
Insert the FPC
Insert the hook
Fit it to the corner of the SD board
HDD Connector Guide
Screw
Screw
Screw
Screw
Screw
Screw
Screw
Thermal Rubber
DIMM Holder
RF SW Knob
9-30
9.2.12.
Setting the Audio PCB
1. Connect the Cable to the Connector. (CN901)
2. Fix the Audio PCB using the 3 Screws. <N9>
2. Fix the Audio PCB using the 3 Screws. <N9>
Note:
Tighten the Screws in the numbered order (No1 to No3).
Screws <N9> : DRSB2+5FKL
Screw
Screw
SD Blind Sheet
Battery FPC Ass’y
Ensure that both top and
bottom are hooked.
bottom are hooked.
Slide the Battery FPC Ass’y
Insert the FPC as illustrated
Side surface
Insert the end of the Sheet into the space between the Main
Board and the bottom of the PCMCIA Slot.
(Left and Right 0.5mm, Apply 20 to 30N (2.0 to 3.0 Kgf))
Board and the bottom of the PCMCIA Slot.
(Left and Right 0.5mm, Apply 20 to 30N (2.0 to 3.0 Kgf))
Attach it fitting to the right.
0 0.5mm
0 0.5mm
<N9>:No1
<N9>:No.2
Audio PCB
Connector(CN901)
<N9>:No.3
9-31
9.2.13.
Setting the HSDPA PCB and Bluetooth PCB
1. Fix the Plate and Bluetooth PCB using the 2 Screws
<N19>.
2. Connect the Cable to the Connector. (CN1)
3. Connect the Cable to the Connector. (CN604)
4. Fix the Plate and the Board using the 4 Screws <N19>.
5. Attach the blue Antenna Cable to the Clamper.
3. Connect the Cable to the Connector. (CN604)
4. Fix the Plate and the Board using the 4 Screws <N19>.
5. Attach the blue Antenna Cable to the Clamper.
6. Connect the Cable to the Connector. (CN600)
7. Fix the RF PCB Ass'y using the 4 Screws. <N9>
8. Attach the Tape.
9. Attach the brown and black Antenna Cables.
7. Fix the RF PCB Ass'y using the 4 Screws. <N9>
8. Attach the Tape.
9. Attach the brown and black Antenna Cables.
10. Attach the Cable Holder Cushion.
Screws <N9> : DRSB2+5FKL
Screws <N19> : XSB2+3FNL
Screws <N19> : XSB2+3FNL
<N19>
<N19>
:No.4
:No.4
<N19>
:No.2
:No.2
Antenna Cable(blue)
Bluetooth PCB
Plate
Clamper
<N19>
:No.1
:No.1
<N19>
:No.1
:No.1
<N9>
<N9>
<N9>
<N9>
Antenna Cable(brown)
Antenna Cable(black)
Antenna Cable(black)
HSDPA PCB
Tape
Cable Holder Cushion
Connector(CN600)
Click on the first or last page to see other CF-19CDBAXVM service manuals if exist.