DOWNLOAD Panasonic KV-S7097 / KV-S7077 Service Manual ↓ Size: 13.74 MB | Pages: 127 in PDF or view online for FREE

97

Shading

1. Click “Shading” on the main menu.
2. Confirm the message “The data of User Shading will be 

also overwritten” on the display. 
And if the message is acceptable, click “OK”.

3. Clean the conveyor, rollers,  and ADF Glasses according 

tothe message on the display.

And click “OK”.

4. Switch Reference Plates to white according to the message 

on the display.

And click “OK”.

5. Set the included Shading Paper or Shading Paper (Part No.: 

See 14.7.) on the Hopper Tray in landscape orientation.

6. And click “OK” to scan the Shading Paper.
7. Switch the Reference Plates to black according to the 

message on the display.

8. Click“OK” to return to the main menu.

—

Until this process is
completed, don’t stop the
process by opening any
doors or turning off the
scanner. 

Shading Data

1. Click “Shading Data” on the adjust menu.
2. Click “Get Shading Data” on the Shading Data. 
3. Save it to selected folder.

—

This data file is used for 
analysis.

All Position

1. Set 2 pcs of test chart A (Part No.:  See 14.7.) on the  Hopper 

Tray in portrait orientation.
And set 1 pcs of test chart A on the Flatbed.

2. Click “All position” on the main menu to execute scanning
    position and length adjustment. 
3. Check the result.
4. Click “OK” to return to the main menu.

—

Set 2 pcs of test chart A on 
the Hopper Tray in order.
 1st page: Front side
 2nd page: Back side

98

Individual Position 1. Adjust Automatically.

    a. Set test chart A (Part No.: See 14.7.) on the Hopper Tray
         or Flatbed.
    b. Click “Individual Position” on the main menu.
    c. Click one of 8 “Adjust Automatically” buttons on the
        “Individual Position” dialog box to execute the
        adjustment.
    d. Check the result.
    e. Click “OK” to finish the adjustment.
     f. Click “OK” to return to the main menu.
2. Adjust Manually.
    a. Click “Individual Position” on the main menu.
    b. Change the parameters (mm, %) on the “Individual
        Position” dialog box as required. (Refer to Remarks.)
    c. Click “OK” to renew the setting, and to return to the
        main menu.

—

1. Adjust Automatically
    8 automatic adjustments
     a. Adjust Length
     b. Adjust Paper End
         Position
     c. Adjust Front V. Position
     d. Adjust Front H. Position
     e. Adjust Back V. Position
     f. Adjust Back H. Position
     g. Adjust FB Length
     h. Adjust FB V. Position
     i. Adjust FB H. Position
 
2. Adjust Manually

(Length)
+: Increasing a value allows 

the scanning image to 
extend vertically.

(Paper End Position)
+: On the LC (Length 

Control) mode, 
increasing a value allows 
the paper-end timing to 
be earlier.

(Vertical Position)
+: Increasing the value 

shifts the document 
image position 
downward.

(Horizontal Position)
+: Increasing the value 

shifts the document 
image position to the 
right.

If the appropriate
scanning position can
not be obtained by any
of the manual
adjustments, check CIS
installation.

99

Double Feed

1. Adjust Automatically.

a. Set the Shading Paper (Part No.: See 14.7.) on the 

Hopper Tray in portrait orientation, sliding the Document 
Guides so that they match the document width.

b. Click “Double Feed” in the “Adjust” section on the main 

menu.

c. Click “Adjust Automatically” on the “Double Feed 

Detector” dialog box to adjust the double feed sensitivity.

d. Check the result.
e. Click “OK” to finish the adjustment.
f. Click “OK” on the “Double Feed Sensor” dialog box to 

return to the main menu.

2. Adjust Manually.
    a. Click “Double Feed” in the “Adjust “ section on the main
        menu.
    b. Change the parameters (“Send Level”)
        on the “Double Feed Detector” dialog box. 
    c. Click “OK” on the “Double Feed Detector” dialog box to
         return to the main menu. 

—

Send Level

Level : 50 to 200

* USB ID

1. Click “USB ID” on the adjust menu.
2. Click “Set” on the “USB ID” dialog box to store a new ID
   number for a new replaced MAIN Board. 
3. Click “Close” to return to the adjust menu.

—

*This setting is available only
  for a newly replaced
  MAIN Board or IC501.

Feed Speed

1. Click "Feed Speed" on the adjust  menu.
2. Change the parameter (%: 10 to 100).
3. Click "OK" to renew the setting, and to return to the adjust 
   menu.
Note:

100 %

100

Sensor Sensitive 
Level

1. Click “Sensor Sensitive Level” on the adjust menu.
Note:

*The adjustment is done for all the sensors below at 

a time.
Waiting Sensor, Starting Sensor, Ending(Front) Sensor.

*Be sure to clean to clean before adjusting and remove dust 

thoroughly from the sensors and reflectors at the opposite 
side with a cotton swab.

*If dust remains on them, the adjustment is not done 

properly and the paper detection may not be able to work.

2. Click “Adjust” on the “Sensor Sensitive Level” dialog box.  

Check each sensor’s sensitive level (Offset  and Slice) on 
the Sensor Sensitive Level dialog box.

3. Click “Close” to return to the adjust menu.

Shading Sheet 
Information

1. Click “Shading Sheet Information”  on the main menu. 
2. Check the Shading Sheet part no.

—

Download the 
latest version

1. Click “Download the latest version” to open the site for 

Panasonic scanner products that provides the scanner 
software to be downloaded. 

—

Error Log 

1. Click “Error Log” to open “Save As” dialog-box. 
2. After renaming a log file, perform “Save” to save it.

Refer to 9.3.3. 

Error Log 

 

—

Select Scanner

1. Click “Select Scanner” on the main menu. 
2. 

Select a scanner connected to the PC

.

—

System Log

1. Click “System Log” on the main menu to save the scanner 

and the PC information as text files. 

—