DOWNLOAD Panasonic KV-S7097 / KV-S7077 Service Manual ↓ Size: 13.74 MB | Pages: 127 in PDF or view online for FREE

93

Maintenance 
Setting

1. Click “

Maintenance Setting” on the main menu.

2. Click “Change” on “Maintenance Setting” dialog box to 

change the parameter value on the “Caution Setting” dialog  
box.

3. Click “Roller Cleaning Notification” or “Roller 

Replacement Notification” check box to inform the caution 
information. 

4. Click “Clear Counter” for each counter on “Maintenance 

Setting” dialog box and according to the message on the 
display, click “OK” to clear each counter. 

5. Click “Scanning Glass Cleaning Notification” check box to 

inform the scanning glass cleaning timing.

6. Click “OK” to renew the setting.

Clean Roller 
Timing: 
20000

Roller 
Cleaning 
Notification:
OFF

Replace 
Roller 
Timing: 
300000

Roller 
Replacement 
Notification:
OFF

Scanning
Glass
Cleaning
Notification:
OFF

Cleaning Mode

1. Close the ADF door.
2. Plug in the power cord and connect the USB cable.
3. Press the power button to turn ON the unit’s power.
4. Start the User Utility.
5. Select Cleaning Mode in User Utility.
6. Press the ADF door release, and open the ADF door.

Raise the Hopper Tray in the and thenpull the Exit Door 
Release to open the Exit Door.

7. Enter Cleaning Mode in User Utility.
8. Clean the conveyor rollers.

a.Use the Roller Cleaning Paper to wipe the dirt from the sur-

faces of the conveyor rollers.

b.Press the Start/Stop button on the scanner to rotate the 

conveyor rollers a small amount.

c.Repeat these steps until all surfaces of all conveyor rollers 

are cleaned.

9. Exit Cleaning Mode after cleaning is completed.

—

Set Default

1. Click “Set Default” on the main menu. 
2. Click “Set Default” on the “Set Default” dialog box to set
    the default values for “Sleep Mode”, and “Maintenance
   Setting”. 
3. Click “Close” to return to the main menu.

—

94

LED

1. Click “LED” on the test menu. 
2. Click “START” on “LED” dialog box to start LED Test
    continuously until clicking “STOP”. 
3. Click “Close” to return to the test menu. 

Each indicator turns on or off
in a constant period.

Key / Sensor

1. Click “Key / Sensor” on the test menu. 
2. Check the key and sensor status on the “Key / Sensor”
    dialog box. 

3. Click “Close” to return to the test menu. 

Sensor Sensitive
Level

1. Click “Sensor Sensitive Level” on the main menu. 
2. Check each sensor’s sensitive level (Offset, Slice) on the
    Sensor Sensitive Level dialog box.
3. Click “Close” to return to the main menu.

Feed Motor

1. Click “Feed Motor” on the main menu.
2. Click “START” on the “Feed Motor” dialog box to start to
    rotate Paper Feed Motor continuously until clicking “STOP”.
3. Click “Close” to return to the main menu.

Conveyor Motor

1. Click “Conveyor Motor” on the main menu. 
2. Click “START” on the “Conveyor Motor” dialog box to start
    to rotate the Conveyor Motor continuously until clicking
    “STOP”. 
3. Click “Close” to return to the main menu.

Hopper Drive

1. Click “Hopper Drive” on the main menu.
2. Click “START” on the “Hopper Drive” dialog box to start
    to execute the Hopper’s Up/Down movement continuously
    until clicking “STOP”.
3. Click “Close” to return to the main menu.

Good result

Offset : less than 255
Slice : 7

95

Feed

1. Set documents on the Hopper Tray.
2. Click “Feed” on the main menu. 
3. Set “Test Mode” and “Test Condition” depending on each
    scanning condition.
      Note:

4. Click “START” on the “Feed” dialog box to start feeding
    documents.
   Note:

     When “Flatbed” on the “Test Mode” is selected, check
     the CIS Carriage’s sliding from one end to the other
    repeatedly is tested.
5. Click “STOP” on the “Feed” dialog box to stop the test.
6. Click “Close” to return to the main menu. 

7-segment LED 
Test

1. Click “7-segment LED” on the test menu. 
2. Click “START” on “7-segment LED” dialog box to start 

7-segment LED Test continuously until clicking “STOP”.

3. Click “Close” to return to the test menu.

Sleep Mode

1. Click “Sleep Mode” on the test menu. 
2. Click “START” on the “Sleep Mode” dialog box to enter the
     sleep mode.
3. Click “STOP” to return from the sleep mode.
4. Click “Close” to return to the test menu.

96

Focus

1. Switch the Reference Plates (F, B) to white.
2. Click “Focus” on the main menu.
3. Set the value for “Gain”. (Value: 140 or less)
4. Select a side (Front or Back).
5. Check “START” of the “Focus” dialog box to start monitor-

ing the image output level graph.

6. Click “STOP” on the “Focus” dialog box to finish the test.
7. Check “Close” to return to the main menu.
8. Open the Exit Door, and then remove the paper.

* “Shading correction” check at the time.

Double Feed 

1. Click “Double Feed” for “Test” item on the test menu. 

2. Set “Send Level” on “Double Feed Sensor” dialog box.
3. Push the ADF Door Release to open the ADF Door.
   And hold a piece of clean white paper between Double feed

sensor (TX) and (R), and then close the ADF Door.

4. Click “START” on the “Double Feed Sensor” dialog box to
    start the double feed sensor’s sensitivity test. 
5. Check whether the peak level is within the specification.
    (See Remarks.) 
6. Click “STOP” to finish this test.
7. Push the ADF Door Release to open the ADF Door.
    And remove the white paper, and then close the ADF Door.
8. Click “Close” to return to the test menu.

Memory

1. Click “Memory” on the test menu.
2. Click “START” on the “Memory” dialog box to start the
    Memory Read / Write Test.
3. Check the result.
4. Click “Close” to return to the test menu.

For details on Error Codes,
refer to Sec. 9.3.2.

Back-graound
Color

Gain

White

140 or less

Good

Result

(Level)

More than 50

*

Send Level

Good result
(Peak Level)

Level: 0 to 200   700 or more