Panasonic NR-F610GT-N8 Service Manual ▷ View online
29
7 Operating Instructions
7.1.
FRESH FREEZING
30
7.2.
Auto Ice-making
31
7.3.
In these case?
32
8 Test Mode
The following tests can be checked Ice-making, Compressor
rotational speed, and other control as needed.
HOW TO SET (SERVICE MODE)
rotational speed, and other control as needed.
HOW TO SET (SERVICE MODE)
HOW TO OPERATE (SERVICE MODE)
• Press [FRIDGE] button to select a menu in ascending order.
• Press [FREEZER] button to select a menu in descending
• Press [FREEZER] button to select a menu in descending
order.
• Press [AUTO ICE OFF] button to perform an operation.
• Press [FRESH FREEZING] button to finish an operation.
• Press [FRESH FREEZING] button to finish an operation.
HOW TO CANCEL (SERVICE MODE)
8.1.
Ice-making Test
Following tests can be confirmed ice release and water supply
status.
status.
• ICE-MAKING TEST-1; For service engineer
It is possible to confirm by sight the operation of the Ice-
maker unit with IC door opened.
maker unit with IC door opened.
• ICE-MAKING TEST-2; For customer and service engineer
After starting test, operation is stopped temporarily when the
door is opened, then it will restart when the door is closed.
(It is described in the OPERATING INSTRUCTIONS)
IC door is opened to confirm the initial operation of Ice-
maker.
door is opened, then it will restart when the door is closed.
(It is described in the OPERATING INSTRUCTIONS)
IC door is opened to confirm the initial operation of Ice-
maker.
8.1.1.
Ice-making Test-1 [P1]
The FC door is closed before starting test, and IC door is
opened to confirm the initial operations of Ice maker.
HOW TO SET/confirmation
opened to confirm the initial operations of Ice maker.
HOW TO SET/confirmation
1. Set in SERVICE MODE.
(Press [FRESH FREEZING] button for 5 seconds.)
2. Press the buttons as follows.
3. Confirm operation of Ice release by the Ice check lever
and revolving of the Ice tray.
4. LED is turned off, and beep stops.
5. Confirm operation of water supply by the water pump
5. Confirm operation of water supply by the water pump
operating sound and water level of the water tank.
8.1.2.
Ice-making Test-2
After starting test, operation is stopped temporarily when the IC
and FC door are opened.(it does not stop during water supply
operation.)
HOW TO SET/confirmation
and FC door are opened.(it does not stop during water supply
operation.)
HOW TO SET/confirmation
1. Press the button as follows.
2. Confirm the sound of the Ice release motor.
3. LED is turned off, and beep stops.
4. Confirm operation of water supply by the water pump
3. LED is turned off, and beep stops.
4. Confirm operation of water supply by the water pump
operating sound and water level of the water tank.
• Water supply(5sec)
Stop(1sec) Reverse (3sec,Back-
flow)
Stop(2sec)Reverse(1sec,Backflow)
Above each period is estimated time.
8.2.
Forced Defrosting
[P3]
• Defrost sensor is operated below the temperature that
defrosting is finished.
• Forced defrosting operation will be automatically finished
when FC temperature (Defrost sensor) rises in certain tem-
perature.
perature.
HOW TO SET
1. Set in SERVICE MODE.
(Press [FRESH FREEZING] button for 5 seconds.)
2. Press the buttons as follows.
How to confirm the operation
1. Set to {QUICK ICE MAKING} function.
Flashing
This function is operating properly.
2. Cancel {QUICK ICE MAKING} after confirming it.
HOW TO CANCEL
• Turn the power OFF.
8.3.
LED AG Test
[P5]
LED AG in PC is normally turned on at the time of powerful
mode, but it can be forcibly turned on.
Even if PC doors are opened, LED AG is not turned off.
HOW TO SET
mode, but it can be forcibly turned on.
Even if PC doors are opened, LED AG is not turned off.
HOW TO SET
1. Set in SERVICE MODE.
(Press [FRESH FREEZING] button for 5 seconds.)
2. Press the buttons as follows.
HOW TO CANCEL
• Turn the power OFF.
Click on the first or last page to see other NR-F610GT-N8 service manuals if exist.