Panasonic UF-885 / UF-895 (serv.man2) Service Manual ▷ View online
38
(10) Remove the Pressure Roller (409).
Caution:
Do not scratch the surface of the Pressure Roller when
removing or re-installing it.
removing or re-installing it.
(11) Remove the Black and the White Bushings (423) (424).
(12) Remove the Eject Roller (422).
(10)
(12)
(11)
White
Black
39
2.11
Fan Duct (520), Printer Motor (650), Motor Bracket (641)
(1) Remove the the Front Cover (105), Rear Cover (108)
(Refer to 2.3), Control Panel Unit and FCB Bracket (523)
(Refer to 2.5).
(Refer to 2.5).
(2) 2 Screws (19).
(3) Remove the Fan Duct (520).
(3) Remove the Fan Duct (520).
(4) 2 Screws (19).
(5) Remove the Fan Duct Bracket (526).
(5) Remove the Fan Duct Bracket (526).
(6) Remove the Harnesses from the 4 clamps.
(7) Disconnect Connectors CN54, 55, 59, 61, 62 and 63 on
(7) Disconnect Connectors CN54, 55, 59, 61, 62 and 63 on
the LPC PC Board.
(8) 5 Screws (19).
(9) Remove the Motor Bracket (641).
(9) Remove the Motor Bracket (641).
(10) 2 Screws (19).
(11) Remove the Printer Motor (650).
(2)
(3)
(11)
(10)
(10)
(11)
(10)
(10)
(11)
(10)
(10)
40
(12) 1 Screw (19).
(13) Remove the Transfer Ground Spring (649).
(14) 7 Gears.
(13) Remove the Transfer Ground Spring (649).
(14) 7 Gears.
Caution:
When re-installing the gear (labeled “6”), be sure to install the
washer on the shaft first.
washer on the shaft first.
Note:
Apply KS-660 Conductive Grease to the Transfer Ground
Spring (649) or to the end of the Feed Roller Shaft (618), see
page 41.
Spring (649) or to the end of the Feed Roller Shaft (618), see
page 41.
(12)
(13)
(14)
(14)
(14)
6
41
2.12 Laser Unit (429), Feed Roller (618), Paper Feed Roller (746), Clutch Gear
Assembly (660), Paper Feed Solenoid (744), Fan Unit (622)
(1) Remove the the Front Cover (105), Rear Cover (108)
(Refer to 2.3), Paper Guide Cover (110) (Refer to 2.4),
Control Panel Unit (Refer to 2.5), and Motor Bracket and
Gear Assembly (Refer to 2.11).
Control Panel Unit (Refer to 2.5), and Motor Bracket and
Gear Assembly (Refer to 2.11).
(2) Disconnect Connectors.
(3) 2 Screws (19).
(4) Remove the Laser Unit (429).
(3) 2 Screws (19).
(4) Remove the Laser Unit (429).
(5) Remove the E34 Drive Gear (620).
Note:
When reassembling, apply KS-660 Conductive Grease to the
end of the Feed Roller Shaft (618).
end of the Feed Roller Shaft (618).
(6) 2 Screws (19).
(7) Remove the Feed Roller (618).
(7) Remove the Feed Roller (618).
(8) 2 Screws (19).
(9) Remove the Paper Feed Roller Assembly.
(9) Remove the Paper Feed Roller Assembly.
(3)
(4)
(2)
(5)
(6)
(7)
(8)
(9)
Click on the first or last page to see other UF-885 / UF-895 (serv.man2) service manuals if exist.