Panasonic UF-885 / UF-895 (serv.man2) Service Manual ▷ View online
34
(13) 2 Screws (19).
(14) Remove the Upper Transfer Guide (635).
(14) Remove the Upper Transfer Guide (635).
(15) Release 2 Latch Hooks.
(16) Remove the Timing Sensor (610).
(16) Remove the Timing Sensor (610).
(17) 2 Screws (19).
(18) Remove the BTR Guide (629).
(19) Remove the Bias Transfer Roller (630).
(18) Remove the BTR Guide (629).
(19) Remove the Bias Transfer Roller (630).
(13)
(14)
(16)
(15)
(19)
(17)
(17)
(18)
Black
White
35
2.9
Fuser Unit (431), Fuser Lamp (408), Thermistor Assembly (405), Paper
Exit Sensor (610)
Exit Sensor (610)
(1) Remove the Left Side Cover (107) (Refer to 2.3).
(2) Disconnect 2 Connectors.
(3) Disconnect the Relay Connector.
(4) 1 Screw (19).
(5) Remove the Ground Strap (653).
(2) Disconnect 2 Connectors.
(3) Disconnect the Relay Connector.
(4) 1 Screw (19).
(5) Remove the Ground Strap (653).
(6) 3 Screws (4N).
(7) Remove the Fuser Unit (431).
(7) Remove the Fuser Unit (431).
(8) 1 Screw (23).
(9) Remove the Fuser Lamp Terminal C (404).
(9) Remove the Fuser Lamp Terminal C (404).
(10) Remove the Fuser Lamp (408).
Caution:
When re-installing the Fuser Lamp, make sure that the Fuser
Lamp is inserted into the Fuser Unit as illustrated on the left.
Do not touch the glass portion of the Fuser Lamp with bare
hands. Grease from the fingerprints will shorten its life cycle,
use isopropyl alcohol to clean fingerprints.
Lamp is inserted into the Fuser Unit as illustrated on the left.
Do not touch the glass portion of the Fuser Lamp with bare
hands. Grease from the fingerprints will shorten its life cycle,
use isopropyl alcohol to clean fingerprints.
(11) 1 Screw (1Q).
(12) Disconnect Connector.
(13) Remove the Thermistor Assembly (405).
(13) Remove the Thermistor Assembly (405).
(2)
(3)
(4)
(5)
(6)
(6)
(7)
(8)
(9)
(10)
(12)
(13)
(11)
36
(14) 2 Screws (23).
(15) Remove the Fuser Cover (401).
(15) Remove the Fuser Cover (401).
(16) Remove the Paper Exit Sensor (610).
(17) Disconnect Connector.
(17) Disconnect Connector.
(14)
(15)
(17)
(16)
37
2.10 Fuser Roller (414), Pressure Roller (409), Eject Roller (422)
(1) Remove the Fuser Unit (431) (Refer to 2.9).
(2) 2 Pressure Springs (412).
(3) 2 C-Rings (418).
(2) 2 Pressure Springs (412).
(3) 2 C-Rings (418).
(4) Remove the E24 Drive Gear (417).
(5) Remove 2 P17L6.8 Bushings (416).
(5) Remove 2 P17L6.8 Bushings (416).
(6) Remove the Fuser Roller (414).
Caution:
Do not scratch the surface of the Fuser Roller when removing
or re-installing it.
or re-installing it.
(7) Remove the E22 Gear (425).
(8) 1 Screw (4N).
(9) Remove the Lower Paper Guide (426).
(8) 1 Screw (4N).
(9) Remove the Lower Paper Guide (426).
(2)
(3)
(5)
(4)
(6)
(8)
(9)
(7)
Click on the first or last page to see other UF-885 / UF-895 (serv.man2) service manuals if exist.