Panasonic UF-885 / UF-895 (serv.man2) Service Manual ▷ View online
30
2.7
ADF Roller (323), Pre-Feed Roller (325), Eject Roller (330), Feed Roller
(328), Transmission Gear Assembly, Transmit Motor (346)
(328), Transmission Gear Assembly, Transmit Motor (346)
(1) Remove the Front Cover (105), Rear Cover (108) (Refer
to 2.3), Control Panel Unit (Refer to 2.5) and the
Transmitter Chassis (301) Assembly (Refer to 2.6).
Transmitter Chassis (301) Assembly (Refer to 2.6).
(2) 1 Screw (19).
(3) Remove the ADF Bracket (317) Assembly.
(4) Remove the ADF Roller (323).
(3) Remove the ADF Bracket (317) Assembly.
(4) Remove the ADF Roller (323).
(5) Remove the Pressure Spring Plate (324).
(6) Remove the Pre-Feed Roller (325).
(6) Remove the Pre-Feed Roller (325).
Note:
Apply Molykote EM-50L Grease to the Pre-Feed Roller (325).
(7) Remove the Ground Spring Plate A (316).
(8) Remove the document Eject Roller (330).
(8) Remove the document Eject Roller (330).
Note:
Apply Molykote EM-50L Grease to the Eject Roller (330).
(9) 2 Screws (19).
(10) Remove the Feed Roller (328).
Note:
Apply Molykote EM-50L Grease to the Feed Roller (328).
(3)
(2)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(10)
(10)
31
(11) Remove the Scanner Glass (341).
(12) Remove the Stamp Head Assembly.
Note:
Before reassembling, clean both sides of the Scanner Glass
(341) with a soft cloth, soaked with isoproyl alcohol.
(341) with a soft cloth, soaked with isoproyl alcohol.
(13) Release the hook on the drive gear.
(14) Remove the B31B61 Drive Gear (314).
(15) Remove the Idle Shaft (331) and the B18 Drive Gear
(14) Remove the B31B61 Drive Gear (314).
(15) Remove the Idle Shaft (331) and the B18 Drive Gear
(348).
Note:
Apply Molykote EM-50L Grease to the Idle Shaft (331).
(16) Remove 2 Latch Coil Springs (303).
(17) Remove 2 Latches (302).
(17) Remove 2 Latches (302).
(12)
(11)
(15)
(14)
(16)
(16)
(17)
(17)
32
(18) 6 Screws (19).
(19) Remove the Motor Bracket A (304) with the Transmission
(19) Remove the Motor Bracket A (304) with the Transmission
Gear Assembly.
Note:
Apply Molykote EM-50L Grease to the Transmit Motor (346)
Gear, B35 Drive Gear (Feed Roller) (326) and B35 Drive
Gear (Eject Roller) (326).
Gear, B35 Drive Gear (Feed Roller) (326) and B35 Drive
Gear (Eject Roller) (326).
(20) Remove the B30 Gear (307).
(21) 2 Screws (36).
(22) Remove the Transmit Motor (346).
(23) Remove the TMOT Harness (347).
(21) 2 Screws (36).
(22) Remove the Transmit Motor (346).
(23) Remove the TMOT Harness (347).
(18)
(19)
x6
(20)
(21)
(23)
(22)
33
2.8
Toner Sensor (639), Timing Sensor (610), Bias Transfer Roller (630)
(1) Open the Printer Cover (122) (Refer to 2.3).
(2) 2 Screws (19).
(3) Remove the Toner Sensor Cover (640).
(4) 1 Screw (19).
(5) Remove the Toner Sensor Assembly.
(6) Disconnect Connector and remove the Harness from the
(2) 2 Screws (19).
(3) Remove the Toner Sensor Cover (640).
(4) 1 Screw (19).
(5) Remove the Toner Sensor Assembly.
(6) Disconnect Connector and remove the Harness from the
Upper Transport Guide.
(7) Remove the Toner Sensor (639).
(8) 4 Screws (19). (Remove the resistor screw first)
(9) Remove the Ground Strap (653).
(9) Remove the Ground Strap (653).
(10) Remove the Transport Unit.
(11) Disconnect Connector from the Timing Sensor.
(12) Remove the Harness from the Transport Unit.
(4)
(2)
(3)
(5)
(6)
(7)
(8)
(10)
(9)
(12)
(11)
Click on the first or last page to see other UF-885 / UF-895 (serv.man2) service manuals if exist.