Panasonic UF-580 / UF-590 / UF-780 / UF-790 / UF-5100 / UF-6000 / UF-6100 Service Manual ▷ View online
45
(19) Remove 2 P6L5.5 Bushings (707).
(20) Remove the Pressure Roller (706).
(20) Remove the Pressure Roller (706).
Caution:
Do not scratch the surface of the Pressure Roller
when removing or reinstalling it.
when removing or reinstalling it.
(19)
(20)
46
2.2.16.
Rear Chassis (505), SNS1 PC Board (1008)
(1) Remove the Power Supply Unit
(Refer to 2.2.12.).
(2) Remove the SC PC Board (Refer to 2.2.12.).
(3) Remove the Fuser Unit (Refer to 2.2.14.).
(4) Remove 6 Screws (19).
(5) Remove the Bracket (403).
(6) Remove the Rear Chassis (505).
(3) Remove the Fuser Unit (Refer to 2.2.14.).
(4) Remove 6 Screws (19).
(5) Remove the Bracket (403).
(6) Remove the Rear Chassis (505).
(7) Disconnect Connectors CN80 and CN81 on the
SNS1 PC Board (1008).
(8) Remove 1 Screw (19).
(9) Remove the SNS1 PC Board (1008).
(9) Remove the SNS1 PC Board (1008).
(4)
(4)
(5)
(6)
(9)
(8)
(7)
47
2.2.17.
Transfer Guide (601) Assembly, Feed Roller (526)
(1) Remove the Rear Chassis (Refer to 2.2.16.).
(2) Remove 2 Screws (C8).
(3) Disconnect Connector CN80 on the SNS1 PC
(2) Remove 2 Screws (C8).
(3) Disconnect Connector CN80 on the SNS1 PC
Board (1008).
(4) Remove the Transfer Guide (601) Assembly.
(5) Remove the 2 Snap Rings. (B9).
(6) Remove the Feed Roller (526).
(6) Remove the Feed Roller (526).
(7) Remove the Roller Gear (529).
(8) Remove 2 P6L5 Bushings (527, 528).
(8) Remove 2 P6L5 Bushings (527, 528).
(2)
(2)
(4)
(3)
(2)
(5)
(6)
(7)
(8)
White
Black
48
2.2.18.
Toner Sensor (513), Laser Unit [LSU] (512), SNS3 PC Board (1009)
(1) Remove the Transmit Guide Assembly
(Refer to 2.2.4.).
(2) Remove 2 Screws (19).
(3) Remove Ground Wire (542).
(4) Remove the CCD Shield Plate (533).
(3) Remove Ground Wire (542).
(4) Remove the CCD Shield Plate (533).
(5) Remove 1 Screw (19).
(6) Disconnect Connector CN84 on the SNS3 PC
(6) Disconnect Connector CN84 on the SNS3 PC
Board (1009).
(7) Remove the Toner Sensor Spring Plate (506)
Assembly.
Note:
When reinstalling, make sure that the Toner
Sensor Spring Plate is inserted into the 2 notches
in the main frame as illustrated.
Sensor Spring Plate is inserted into the 2 notches
in the main frame as illustrated.
(8) Remove the Toner Sensor (513).
(9) Disconnect the Connector on the Toner Sensor.
(9) Disconnect the Connector on the Toner Sensor.
(2)
(4)
(3)
(6)
(5)
(7)
UF-580/590
UF-5100/6100
UF-5100/6100
(8)
(9)
UF-5100/6100
UF-580/590
UF-780/790
UF-6000
UF-6000
(8)
(9)
Click on the first or last page to see other UF-580 / UF-590 / UF-780 / UF-790 / UF-5100 / UF-6000 / UF-6100 service manuals if exist.