Panasonic DMC-FT20EE Service Manual ▷ View online
29
Replacing the waterproof packing
• The location of waterproof packing are shown at right. (5 types, 6 packings in total)
• Waterproof packings are supplied as Waterproof packing kit (Part No.: VUMG2032).
• Waterproof packings are supplied as Waterproof packing kit (Part No.: VUMG2032).
< Note for replacement >
• Do not touch the waterproof packings directly by the hand.
• Do not perform cleaning of waterproof packings by the solvent of alcohol etc. or by blowing air.
• Take care not to put any foreign objects (garbage and dust).
• Use the silicon chips (Part No.: RFKZ0478) when replacing the Case O-ring.
• Do not perform cleaning of waterproof packings by the solvent of alcohol etc. or by blowing air.
• Take care not to put any foreign objects (garbage and dust).
• Use the silicon chips (Part No.: RFKZ0478) when replacing the Case O-ring.
30
7.2.
Air-leak Test
Due to the waterproof performance retention, perform the air-leak test using Air-leak tester (Part No.:RFKZ0528) before/after
servicing when disassembling and assembling the unit.
*The Air-leak test before servicing is necessary to be performed to check whether the malfunction occurred due to air-leak or not.
servicing when disassembling and assembling the unit.
*The Air-leak test before servicing is necessary to be performed to check whether the malfunction occurred due to air-leak or not.
1. Preparation:
1) By referring the "9.3. Disassembly procedures", remove the side ornament R and front almi case unit.
2) Confirm that no foreign objects at the side door, and it is firmly closed.
2) Confirm that no foreign objects at the side door, and it is firmly closed.
2. Air-leak Test (Inspection):
*Perform the air-leak test by referring the following procedure.
Note:
Note:
As for the detail instruction of air-leak tester, refer to the operating guide (attached to the product).
[Preparation]
1. Put the camera with the top case facing upward condition.
2. Set the following measurement pressure value on the air-leak tester. (Part No.:RFKZ0528).
1. Put the camera with the top case facing upward condition.
2. Set the following measurement pressure value on the air-leak tester. (Part No.:RFKZ0528).
*About the Setting methods, refer to the operating guide for air-leak tester.
3. Attach "L" size of absorption pad to the tip of the hose of the air-leak tester.
4. Put the absorption pad of air-leak tester vertically on the Inspection point.
Note:
3. Attach "L" size of absorption pad to the tip of the hose of the air-leak tester.
4. Put the absorption pad of air-leak tester vertically on the Inspection point.
Note:
• Keep firmly hold above condition until the measurement is completed.
Once pad is tilted/misaligned from the test hole during testing process, start it from this step.
31
Q
Measuring condition (For DMC-FT20, DMC-TS20)
*Attach "L" size of absorption pad.
[Exhaust Air]
5. Operate the measurement switch of the air-leak tester to exhaust air inside the product for 90 seconds.
[Stand-by]
6. After a laps of 15 seconds, take a note (Record) that the pressure value indicated on the indication panel.
[Measurement]
7. Confirm that the pressure value fluctuations during measurement process are within the testing specification.
5. Operate the measurement switch of the air-leak tester to exhaust air inside the product for 90 seconds.
[Stand-by]
6. After a laps of 15 seconds, take a note (Record) that the pressure value indicated on the indication panel.
[Measurement]
7. Confirm that the pressure value fluctuations during measurement process are within the testing specification.
The air-leak test is now completed.
3. Packing replacement record input:
• To enter the repair record, it is necessary to use the "DIAS" software. The maintenance software "DIAS" is available at "TSN
Website".
To download, click on "Support Information from NWBG/VDBG-AVC".
*DIAS (DSC Integrated Assist Software)
To download, click on "Support Information from NWBG/VDBG-AVC".
*DIAS (DSC Integrated Assist Software)
32
8 Service Fixture & Tools
8.1.
Service Fixture and Tools
The following Service Fixture and tools are used for checking and servicing this unit.
Click on the first or last page to see other DMC-FT20EE service manuals if exist.