Panasonic WV-CP480 / WV-CP484E Service Manual ▷ View online
2-4
4. Connection and Setting Up for
Adjustment
4.1. Connection
8
The Fig. 4-1-1 shows the connecting diagram for the
Adjustment Procedure.
Adjustment Procedure.
8
Connect the Underscanned Colour Video Monitor to the
VIDEO OUT Connector of the Remote E.V.R. Adjustment
Kit through the Vectorscope by using the coaxial cables.
VIDEO OUT Connector of the Remote E.V.R. Adjustment
Kit through the Vectorscope by using the coaxial cables.
8
Connect the Video Output Connector of the WV-
CP480/WV-CP484E to the CAMERA IN Connector of the
Remote E.V.R. Adjustment Kit by using coaxial cable.
CP480/WV-CP484E to the CAMERA IN Connector of the
Remote E.V.R. Adjustment Kit by using coaxial cable.
8
Terminate the input terminal of the Underscanned Colour
Video monitor with 75
Video monitor with 75
Ω
.
8
Connect the 24 V AC or 12 V DC Power Supply Unit to
the Power Input Terminal of the WV-CP484E.
the Power Input Terminal of the WV-CP484E.
8
Connect the 12 V DC Power Supply Unit to the E.V.R.
Adjustment Kit.
Adjustment Kit.
8
Connect the Remote E.V.R. Adjustment Kit to the
Personel Computer (IBM PC/AT type) by using the
Standard Straight RS-232C cable.
Personel Computer (IBM PC/AT type) by using the
Standard Straight RS-232C cable.
8
Connect the probe of the Oscilloscope or Frequency
Counter at the desired Test point in each adjustment
step.
Counter at the desired Test point in each adjustment
step.
Fig. 4-1-1
Test Chart
Floppy
Disk
Disk
Underscanned
Colour
Video Monitor
Colour
Video Monitor
Remote E.V.R.
Adjustment
Kit
Standard
Straight
RS-232C
Cable
Straight
RS-232C
Cable
RS232C
DC12V
IN
IN
Personal
Computer
Computer
75
Ω
WV-CP480
WV-CP484E
WV-CP484E
Vectorscope
(For WV-CP484E)
220 V - 240 V AC
(For WV-CP480)
(For WV-CP480)
CAMERA
IN
VIDEO
OUT
Video Output
Connector
Connector
AC Inlet (WV-CP480)
Power Input Terminal
(WV-CP484E)
Power Input Terminal
(WV-CP484E)
24 V AC or 12 V DC
Power Supply Unit
Power Supply Unit
12 V DC
Power Supply Unit
Power Supply Unit
8
Referring to Fig. 3-3, remove two screws that secure the
CCD Ass'y (IC102) and remove the CCD Ass'y (IC102)
from the ABF Chassis Ass'y.
CCD Ass'y (IC102) and remove the CCD Ass'y (IC102)
from the ABF Chassis Ass'y.
Fig. 3-3
ABF Chassis Ass’y
CCD Ass’y
(IC102)
(IC102)
ABF Motor Ass’y
Remove two screws.
2-5
REMOTE
OPERATE
PROG
ALARM
RESET
RESET
NORMAL
SYSTEM
ALARM OFF
EVR
Left
Switch
Right
Switch
Mode Selection
Switch
Program
Switch
Up
Switch
Down
Switch
Set
Switch
IN
OUT
STD. CAMERA
VP CAMERA
VIDEO
CAMERA
DC12V IN
RS232C
VP/STD Camera Selection Switch
RS232C Connector
4.2. Setting Up for Remote E.V.R.
Adjustment Kit
(1) Remote E.V.R. Adjustment Kit
Fig. 4-2-1
(2) Switch Setting
8
Remove the Upper Cover.
8
Set the switch SW3 on the Board to the position as
shown in Fig. 4-2-2.
shown in Fig. 4-2-2.
Fig. 4-2-2
8
Set the VP/STD.Camera Selection Switch on the Rear
Panel to STD CAMERA position.
Panel to STD CAMERA position.
<Rear>
<F
ront>
Board
SW3
ON
<SW3>
<SW3>
1 2 3 4
Select switch #2 to ON (PAL) position.
#
ON
OFF
1
FIX
2
NTSC
PAL
3
FIX
4
FIX
(3) Menu Setting
8
Set the Mode Selection Switch on the Front Panel to the
"ALARM OFF" (center) position.
"ALARM OFF" (center) position.
8
Keep pressing the Program Switch for 3 seconds or more
until "Program Menu" is displayed on the monitor screen.
until "Program Menu" is displayed on the monitor screen.
8
Move the cursor to the "Controller Set Up" position by
pressing the Up and Down Switch.
pressing the Up and Down Switch.
8
Display the "Controller Set Up Menu" on the monitor by
pressing the Set Switch.
pressing the Set Switch.
8
Move the cursor to the "Set Up Disable" position by press-
ing the Up and Down Switch.
ing the Up and Down Switch.
8
Change "Disable" to "Enable" by pressing the Set Switch.
8
After completing the above setting, move the cursor to the
Communication position by pressing the Up and Down
Switch.
Communication position by pressing the Up and Down
Switch.
8
Display the "Communication Menu" on the monitor by
pressing the Set Switch .
pressing the Set Switch .
8
After confirming the Baud Rate is 9600, finish this menu
by pressing the Program Switch twice.
by pressing the Program Switch twice.
(4) Installing E.V.R Adjustment Program
8
Make a copy of following necessory files to your computer
from original floppy disk.
from original floppy disk.
RADJ2.EXE
CP480E.SEQ
CP48EABF.SEQ
CP480E.EV2
8
The Example given here is for A 2 drive computer, your
procedure might vary slightly depending on the drive con-
figuration.
procedure might vary slightly depending on the drive con-
figuration.
8
Confirm that the contents of CONFIG.SYS file on your
computer is DEVICE=ANSI.SYS (Basic).
computer is DEVICE=ANSI.SYS (Basic).
8
Insert floppy disk containing the E.V.R. Adjustment
Program into your floppy drive (for example,drive:A) and
type A:
Program into your floppy drive (for example,drive:A) and
type A:
8
At the prompt, type CD IBMPC and press ENTER key.
8
Type COPY RADJ2.EXE B: and press ENTER key.
8
Type CD\ and press ENTER key.
8
Type CD SEQ and press ENTER key.
8
Type COPY CP480E.SEQ B: and press ENTER key.
8
Type COPY CP48EABF.SEQ B: and press ENTER key.
8
Type CD\ and press ENTER key.
8
Type CD EVR and press ENTER key.
8
Type COPY CP480E.EV2 B: and press ENTER key.
8
After completing installation of program, you are ready to
use the E.V.R. Adjustment Program.
use the E.V.R. Adjustment Program.
4.3. Setting Up
8
An initial setting of the Switch on the Left side Panel of the
WV-CP480 or on the Rear Panel of the WV-CP484E as
follows:
Gen-Lock Termination Switch
WV-CP480 or on the Rear Panel of the WV-CP484E as
follows:
Gen-Lock Termination Switch
(Hi-Z, G/L 75
Ω
) ....................................................G/L 75
Ω
8
The adjustments should be done with this initial setting,
unless otherwise specified.
unless otherwise specified.
8
The adjustments should be done after 10 minutes warm
up.
up.
2-6
5. Adjustment Procedure
8
The Location of Test Points and Adjusting controls refer
to Wiring Diagram on page 3-1 and 3-2.
to Wiring Diagram on page 3-1 and 3-2.
5.1. Adjustment Procedure-1
(1) Flange back (Back Focus) Adjustment
Test Point:
Video Output Connector (CN7)
I/F Board
8
Before adjustment, read the Hints column below.
This adjustment is available only if SETUP-SW LOCK is
set to OFF in the BACK-FOCUS SETUP menu.
This adjustment is available only if SETUP-SW LOCK is
set to OFF in the BACK-FOCUS SETUP menu.
8
Aim the Camera at the targeting objects and if applicable
adjustment the zoom angle.
adjustment the zoom angle.
8
Press the SET button. (Refer to the Fig. 5-1-1.)
A bar graph with "I" cursor and INDICATOR (4-digit num-
ber) will be overlaid on the camera picture as shown in Fig.
5-1-2.
ber) will be overlaid on the camera picture as shown in Fig.
5-1-2.
Back focus will be automatically adjusted.
8
If needed, perform manual adjustment using the L and R
buttons to obtain the best focus on the targeted object
while observing the picture. See INDICATOR for refer-
ence.
The bar graph will disappear if no operation is performed
for around 10 seconds.
buttons to obtain the best focus on the targeted object
while observing the picture. See INDICATOR for refer-
ence.
The bar graph will disappear if no operation is performed
for around 10 seconds.
Important: Do not use the ABF function for continuous or
repetitive purposes (ex. auto-focus etc.). This function is
to be used to correct defocus caused by switching
between colour and black - and - white when/after
installing the camera.
repetitive purposes (ex. auto-focus etc.). This function is
to be used to correct defocus caused by switching
between colour and black - and - white when/after
installing the camera.
POWER
(UP)
(LEFT)
(RIGHT)
(DOWN)
(SET)
NEAR
G /L75
FAR
ABF/MENU
VIDEO OUT
GEN-LOCK
Hi-Z
1 - 2 - AC24V IN
1 - 2 - DC12V IN
GND
(UP)
(LEFT)
(RIGHT)
(DOWN)
(SET)
FAR
ABF/MENU
Hi-Z
G /L75
NEAR
(WV-CP480)
(WV-CP484E)
SET Button
SET Button
Slide the SW Cover.
Fig. 5-1-1
**MANUAL-ADJ**
NEAR FAR
.........I..........
.........I..........
INDICATOR 9999
RET TOP END
RET TOP END
Fig. 5-1-2
Hints
Before Back-focus Adjustment
•
Adjustment procedures vary depending on the lens.
Refer to the instructions included with the lens.
Refer to the instructions included with the lens.
•
Reset the back-focus by pressing the L and R but-
tons simultaneously on the camera, and adjust the
back-focus.
tons simultaneously on the camera, and adjust the
back-focus.
•
Move the lens focus to the FAR-end when using a
fixed-focal lens (lens focus adjustable type), and
adjust the back-focus.
fixed-focal lens (lens focus adjustable type), and
adjust the back-focus.
For Adjusting the Focus
•
It is recommended that you lower the lighting for the
object to be as dim as possible when adjusting the
focus with an auto iris lens. This will make the iris
open and will result in an accurate focus even
though the lighting conditions vary. This may be
slightly different from the best focus point in a specif-
ic lighting condition.
object to be as dim as possible when adjusting the
focus with an auto iris lens. This will make the iris
open and will result in an accurate focus even
though the lighting conditions vary. This may be
slightly different from the best focus point in a specif-
ic lighting condition.
•
Compared with cases under visible lights, using
near-infrared lights may somewhat deviate the
focus. It is recommended that you select AUTO or
PRESET for C/L
near-infrared lights may somewhat deviate the
focus. It is recommended that you select AUTO or
PRESET for C/L
← →
B/W in the BACK-FOCUS
SETUP menu to obtain a proper focus for each of
visible and near-infrared lights.
visible and near-infrared lights.
For Using General Vari-focal Lenses
1. Aim at the objects 10 meters away or more to adjust
the back-focus.
2. For 8x and 10x class lenses, set the zoom to the
WIDE-end and the focus to the FAR-end, and then
adjust the back focus.
adjust the back focus.
3. For 2x and 3x class lenses, set the zoom to the
TELE-end and the focus to the FAR-end, and then
adjust the back focus.
adjust the back focus.
4. Aim the camera at the targeted objects to place
them in the center then coarsely adjust the zoom
angle and the focus of the lens. Finally, perform
adjustment of the back-focus in either ways of using
ABF (automatically) or MANUAL-ADJ (manually).
angle and the focus of the lens. Finally, perform
adjustment of the back-focus in either ways of using
ABF (automatically) or MANUAL-ADJ (manually).
Note: There may be lenses having an extended range
in lens focus adjustment, except Panasonic lenses.
When using such a lens, set the lens focus back
appropriately from the applicable end position in the
above step 2 and 3 depending on the lens, and then
perform back-focus adjustment. The back-focus will
not be properly adjusted if the lens focus is posi-
tioned into the extended range.
When using such a lens, set the lens focus back
appropriately from the applicable end position in the
above step 2 and 3 depending on the lens, and then
perform back-focus adjustment. The back-focus will
not be properly adjusted if the lens focus is posi-
tioned into the extended range.
(1.2) Line Lock Subcarrier Frequency
Adjustment
Test Point:
TD902 or TD903 (SC VCXO)
Main Board
8
Connect the Frequncy Counter to TD902 or TD903.
8
Adjust data with the ARROW keys so that the Line Lock
Subcarrier Frequency becomes 17.73447 MHz ± 40 Hz.
Subcarrier Frequency becomes 17.73447 MHz ± 40 Hz.
8
Press the ENTER key for next adjustment.
(2) High Clip Level Adjustment
Test Point:
Video Output Connector (CN7)
I/F Board
8
Confirm the Colour Temperature at 3 200°K.
8
Aim the Camera at the Logarithmic Gray Scale Chart.
8
Connect the terminated Oscilloscope with 75
Ω
to the
Video Output Connector.
8
Adjust data with the ARROW keys so that the signal level
becomes 805 mV mV as shown in Fig. 5-2-2.
becomes 805 mV mV as shown in Fig. 5-2-2.
8
Press the ENTER key for next adjustment.
(3) Pedestal Adjustment
Test Point:
Video Output Connector (CN7)
I/F Board
8
Connect the terminated Oscilloscope with 75
Ω
to the
Video Output Connector.
8
Adjust data with the ARROW keys so that the Pedestal
level becoms 50 mV ± 5 mV as shown in Fig. 5-2-3.
level becoms 50 mV ± 5 mV as shown in Fig. 5-2-3.
8
Press the ENTER key for next adjustment.
2-7
5.2 Adjustment Procedure-2
(E.V.R. Adjustment)
8
Mount the ALC Lens on the Camera.
8
Insert new floppy disk containing DOS Operating System
and the E.V.R. Adjustment Program into IBM PC/AT and
turn on the Power Switch of IBM PC/AT.
and the E.V.R. Adjustment Program into IBM PC/AT and
turn on the Power Switch of IBM PC/AT.
8
When starting an adjustment, at the prompt, type
RADJ2 CP480E and press the ENTER key, then the ini-
tial menu page as shown in Fig. 5-2-1 will be displayed.
RADJ2 CP480E and press the ENTER key, then the ini-
tial menu page as shown in Fig. 5-2-1 will be displayed.
8
Press the SAVE (F5) key of the Computer, then the
Computer will ask you for the file name.
Computer will ask you for the file name.
8
Type xxxxxxxx.EV2 0000 09DF. Give an appropriate file
name for xxxxxxxx within 8 letters, but do not use
CP480E.
name for xxxxxxxx within 8 letters, but do not use
CP480E.
8
Press the ENTER key.
8
This saving procedure is recommended to keep the cur-
rent adjustment status of the Camera.
rent adjustment status of the Camera.
8
Press the LOAD (F1) key and type CP480E.EV2 and
press the ENTER key for presetting adjustment of the
Camera.
press the ENTER key for presetting adjustment of the
Camera.
(1.1) Subcarrier Frequency Adjustment
Test Point:
TD902 or TD903 (SC VCXO)
Main Board
8
Connect the Frequncy Counter to TD902 or TD903.
8
Adjust data with the ARROW keys so that the Subcarrier
Frequency becomes 17.73447 MHz ± 40 Hz.
Frequency becomes 17.73447 MHz ± 40 Hz.
8
Press the ENTER key for next adjustment.
Fig. 5-2-1
PANASONIC REMOTE EVR ADJUSTMENT SYSTEM CCTV PRODUCT:CP480 EEPROM:0
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
MENU
✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽ ✽
Page (1/1)
✽ ✽ ✽ ✽ ✽
PAL
1.1. SC FREQUENCY
10.2. 5100K B_GAIN
1.2. LL SC FREQUENCY
11. HIGH LIGHT CHROMA CLIP
2. HI CLIP LEVEL
12.1. LL ADJUSTMENT1
3. PEDESTAL
12.2. LL ADJUSTMENT2
4. ALC DC
5.1.VIDEO OUT GAIN (Low)
5.2.VIDEO OUT GAIN (High)
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.1. WB 3200K MANU OFFSET R
7.2. WB 3200K MANU OFFSET B
8.1. WB 6500K ATW LIMIT R
8.2. WB 6500K ATW LIMIT B
9.1. 3200K R_GAIN
9.2. 3200K B_GAIN
9.4. 3200K R_PHASE
9.5. 3200K B_PHASE
10.1. 5100K R_GAIN
5.1.VIDEO OUT GAIN (Low)
5.2.VIDEO OUT GAIN (High)
6.1. BURST LEVEL
6.2. BURST LEVEL
6.3. BURST LEVEL
6.4. BURST LEVEL
7.1. WB 3200K MANU OFFSET R
7.2. WB 3200K MANU OFFSET B
8.1. WB 6500K ATW LIMIT R
8.2. WB 6500K ATW LIMIT B
9.1. 3200K R_GAIN
9.2. 3200K B_GAIN
9.4. 3200K R_PHASE
9.5. 3200K B_PHASE
10.1. 5100K R_GAIN
<CONTENTS> 17.73447 Mz ± 40Hz TD902,TD903
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
<INSTRUCTION> PLEASE CHOOSE MENU DATA BY ARROW-KEY
LOAD (F1) QUIT (F3) SAVE (F5)
805 mV
+ 35
– 0
– 0
Fig. 5-2-2
+35
–0
50 mV
±
5 mV
Fig. 5-2-3
Click on the first or last page to see other WV-CP480 / WV-CP484E service manuals if exist.