Panasonic SC-HC10EB / SC-HC10EG / SC-HC10EP Service Manual ▷ View online
29
Caution 1 : During assembling, ensure the Sub Rear Panel
is properly slot into the holes.
Caution 2 : During assembling, ensure Sub Rear Panel
properly seated on the Rear Cabinet.
9.6.
Disassembly of Tuner P.C.B.
• Refer to "Disassembly of Stand Unit”
• Refer to "Disassembly of Sub Rear Panel"
• Refer to "Disassembly of Sub Rear Panel"
Step 1 : Remove 1 screw.
Step 2 : Lift & flip Tuner P.C.B..
Step 2 : Lift & flip Tuner P.C.B..
Step 3 : Detach 9P FFC at the connector (CN51) on Tuner
P.C.B..
Step 4 : Remove Tuner P.C.B..
P.C.B..
Step 4 : Remove Tuner P.C.B..
30
Caution : Ensure the 9P FFC (CN51) wire is dressed as dia-
gram shown.
9.7.
Disassembly of SMPS P.C.B.
• Refer to "Disassembly of Stand Unit”
• Refer to "Disassembly of Sub Rear Panel"
• Refer to "Disassembly of Sub Rear Panel"
Step 1 : Remove 1 screw.
Step 2 : Remove SMPS Shield Plate B.
31
Step 3 : Desolder 8P cable at the connector (CN905) on the
SMPS P.C.B..
Step 4 : Remove 2 screws.
Step 5 : Remove SMPS P.C.B..
SMPS P.C.B..
Step 4 : Remove 2 screws.
Step 5 : Remove SMPS P.C.B..
9.8.
Replacement of Switching Reg-
ulator IC (IC702)
ulator IC (IC702)
• Refer to "Disassembly of SMPS P.C.B."
9.8.1.
Disassembly of Switching Regula-
tor IC (IC702)
tor IC (IC702)
Caution : Handle the heatsink unit and P.C.B. with caution
due to its high temperature after prolonged use. Touching
it may lead to injuries.
Step 1 : Desolder pins of the Switching Regulator IC (IC702) on
the solder side of SMPS P.C.B..
the solder side of SMPS P.C.B..
Step 2 : Remove 1 screw.
32
Step 3 : Remove the Switching Regulator IC (IC702).
9.8.2.
Assembly of Switching Regulator
IC (IC702)
IC (IC702)
Step 1 : Apply grease to the heatsink unit.
Step 2 : Install the Switching Regulator IC (IC702) onto SMPS
P.C.B.
Step 3 : Fix the Switching Regulator IC (IC702) onto the heat-
sink unit with 1 screws.
Caution : Ensure the Switching Regulator IC (IC702) is
Step 2 : Install the Switching Regulator IC (IC702) onto SMPS
P.C.B.
Step 3 : Fix the Switching Regulator IC (IC702) onto the heat-
sink unit with 1 screws.
Caution : Ensure the Switching Regulator IC (IC702) is
fixed properly to the heatsink.
Step 4 : Solder pins of the Switching Regulator IC (IC702).
Caution : Ensure the Switching Regulator IC (IC702) is
Caution : Ensure the Switching Regulator IC (IC702) is
seated properly onto the SMPS P.C.B. before soldering
Click on the first or last page to see other SC-HC10EB / SC-HC10EG / SC-HC10EP service manuals if exist.