Panasonic SA-VK880EE / SC-VK880EE Service Manual ▷ View online
45
7.1.3.4.
D-Amp IC Configuration
Figure 5 D-Amp IC Configuration
VK880EE-K
Pin (10)
Sub-Woofer +
IC5300
Pin (14)
Sub-Woofer -
Pin (10)
Center +
IC5200
Pin (14)
Center-
Pin (10)
Front Right
IC5000
Pin (14)
Front Left
Pin (10)
Surround
Right
IC5400
Pin (14)
Surround
Left
46
7.2.
Basic Troubleshooting Guide for Traverse Unit (DVD Module P.C.B.)
Problems Checking
Points
Checking
components
b) Check video signals (Y,C)
LB8301, R8321, R8323,
LB8302, R8325, R8327
LB8302, R8325, R8327
a) Check SDRAM address, data
bus, CLK and other control signals
waveform
bus, CLK and other control signals
waveform
IC8051
1) Distorted picture or
abnormal sound is head
during the initialization
abnormal sound is head
during the initialization
c) Check audio DAC circuitry
* Compare the above with
OK condition DVD Module
P.C.B
OK condition DVD Module
P.C.B
IC8420 (Pin 3, 10 to 11)
LB8421, LB8422
*Check for solder short and/or
component missing/damaged
*Check for solder short and/or
component missing/damaged
b) Check laser drive circuitry
(Voltages & current)
(Voltages & current)
Q8551, Q8552 (For DVD),
Q8561, Q8562 (For CD)
Q8561, Q8562 (For CD)
a) Check motor driver circuitry
(+5V)
(+5V)
IC8251 Pin 8, 21
2) No TOC/Long TOC
c) Check LSI IC connection to
motor drive circuitry
* Compare the above with OK
condition DVD Module P.C.B.
* Compare the above with OK
condition DVD Module P.C.B.
IC8001 Pin 66, 67
IC8251 Pin 15 to 16, 17, 18
* Check for solder short and/or
component missing/damaged
IC8251 Pin 15 to 16, 17, 18
* Check for solder short and/or
component missing/damaged
a) Check connection from
DVD Module to Traverse unit
DVD Module to Traverse unit
FP8251
3) Disc not spinning
4) Traverse not moving
5) Traverse and spindle
abnormal movement
4) Traverse not moving
5) Traverse and spindle
abnormal movement
b) Check motor driver circuitry on
the voltages and control signals
* Compare the above with
OK condition DVD Module P.C.B.
the voltages and control signals
* Compare the above with
OK condition DVD Module P.C.B.
IC8251
* Check for solder short and/or
component damaged
component damaged
6) Cannot read the disc but
spindle motor is spinning
spindle motor is spinning
- Cannot read CD/DVD
a) Check laser drive circuitry
(voltages and current)
(voltages and current)
- Check CD Laser Drive
- Check DVD Laser Drive
* Check voltages and LD current
and compare with OK condition
DVD Module P.C.B.
Q8551, Q8552, LB8551
(For DVD Laser Drive current)
Q8561, Q8562, LB8561
(For CD Laser Drive current)
(For DVD Laser Drive current)
Q8561, Q8562, LB8561
(For CD Laser Drive current)
7) Block Noise during play
a) Check SDRAM IC address and
data bus signal
IC8051
8) Jitter out of specification
a) Check LD current
b) Check OPU (Change to other
unit and confirmed operating
condition)
unit and confirmed operating
condition)
OPU Unit (Traverse unit), FPC
connection (FP8531 & FP8251)
connection (FP8531 & FP8251)
47
8 Service Fixture & Tools
8.1.
Service Tools and Equipment
Prepare service tools before process service position.
Service Tools
Remarks
Main P.C.B. (CN2808) - D-Amp P.C.B. (CN5050)
REEX0930 (17P FFC)
Main P.C.B. (ZJ2701) - SMPS P.C.B. (CN5802)
REXX0680 (11P Cable)
SMPS P.C.B. (H5801) - D-Amp P.C.B. (CN5500)
REXX0683 (8P Cable)
48
9 Disassembly and Assembly Instructions
“ATTENTION SERVICER”
Be careful when disassembling and servicing.
Some chassis components may have sharp edges.
Be careful when disassembling and servicing.
Some chassis components may have sharp edges.
Special Note:
1. This section describes the disassembly procedures for all the major printed circuit boards and main components.
2. Before the disassembly process was carried out, do take special note that all safety precautions are to be carried
2. Before the disassembly process was carried out, do take special note that all safety precautions are to be carried
out.
(Ensure that no AC power supply is connected during disassembling.)
(Ensure that no AC power supply is connected during disassembling.)
3. For assembly after operation checks or replacement, reverse the respective procedures.
Special reassembly procedures are described only when required.
4. Do take note of the locators on each printed circuit board during reassembling procedures.
5. The Switch Regulator IC may have high temperature after prolonged use.
6. Use caution when removing the top cabinet and avoid touching heat sinks located in the unit.
5. The Switch Regulator IC may have high temperature after prolonged use.
6. Use caution when removing the top cabinet and avoid touching heat sinks located in the unit.
7. Select items from the following index when checks or replacement are required.
• Disassembly of Top Cabinet
• Disassembly of DVD Mechanism Unit (CR14D)
• Disassembly of Rear Panel
• Disassembly of Front Panel Assembly
• Disassembly of Panel P.C.B., Volume P.C.B., Remote Sensor P.C.B., Side Bar (L/R) LED P.C.B.
• Disassembly of Mic P.C.B.
• Disassembly of USB P.C.B.
• Disassembly of Music Port P.C.B.
• Disassembly of CD Lid
• Disassembly of Deck Mechanism Unit
• Disassembly of Deck P.C.B.
• Disassembly of Deck Mechanism
• Disassembly of Deck Mechanism P.C.B.
• Disassembly of Cassette Lid
• Rectification for Tape Jam Problem
• Disassembly of D-Amp P.C.B.
• Replacement of Audio Digital Power Amp IC (IC5000)
• Replacement of Audio Digital Power Amp IC (IC5200)
• Replacement of Audio Digital Power Amp IC (IC5300)
• Replacement of Audio Digital Power Amp IC (IC5400)
• Disassembly of Main P.C.B.
• Disassembly of SMPS P.C.B.
• Replacement for Switching Regulator IC (IC5701)
• Replacement for Switching Regulator Diode (D5702)
• Replacement for Regulator Diode (D5801)
• Replacement for Regulator Diode (D5802)
• Replacement for Regulator Diode (D5803)
• Disassembly of AC Inlet P.C.B.
• Disassembly of DVD Module P.C.B.
• Disassembling and Assembling of Traverse Unit.
• Disassembly of DVD Mechanism Unit (CR14D)
• Disassembly of Rear Panel
• Disassembly of Front Panel Assembly
• Disassembly of Panel P.C.B., Volume P.C.B., Remote Sensor P.C.B., Side Bar (L/R) LED P.C.B.
• Disassembly of Mic P.C.B.
• Disassembly of USB P.C.B.
• Disassembly of Music Port P.C.B.
• Disassembly of CD Lid
• Disassembly of Deck Mechanism Unit
• Disassembly of Deck P.C.B.
• Disassembly of Deck Mechanism
• Disassembly of Deck Mechanism P.C.B.
• Disassembly of Cassette Lid
• Rectification for Tape Jam Problem
• Disassembly of D-Amp P.C.B.
• Replacement of Audio Digital Power Amp IC (IC5000)
• Replacement of Audio Digital Power Amp IC (IC5200)
• Replacement of Audio Digital Power Amp IC (IC5300)
• Replacement of Audio Digital Power Amp IC (IC5400)
• Disassembly of Main P.C.B.
• Disassembly of SMPS P.C.B.
• Replacement for Switching Regulator IC (IC5701)
• Replacement for Switching Regulator Diode (D5702)
• Replacement for Regulator Diode (D5801)
• Replacement for Regulator Diode (D5802)
• Replacement for Regulator Diode (D5803)
• Disassembly of AC Inlet P.C.B.
• Disassembly of DVD Module P.C.B.
• Disassembling and Assembling of Traverse Unit.
Below shown is part no. of different screws types used:
Click on the first or last page to see other SA-VK880EE / SC-VK880EE service manuals if exist.