Panasonic SA-VK860EE Service Manual ▷ View online
9.4. DVD Self Diagnostic Function-Error Code
9.4.1. DVD Module Error Code Table
Error
Code
U702 HDMI/DVI I2C
U702 HDMI/DVI I2C
The communication error of I2C
Press [ STOP] on
communication error when connecting it with HDMI/
main unit for next error.
DVI. For instance, when EDID
information to which information on the
TV set side has been described
cannot be read, it is generated.
information to which information on the
TV set side has been described
cannot be read, it is generated.
U703 HDMI/DVI attestation When attestation (HDCP) with the TV
Press [ STOP] on
error
side fails when connecting it with
main unit for next error.
HDMI/DVI, it is generated.
U704 HDMI/DVI SRM
It is generated at the equipment to
Press [ STOP] on
Riborcerar
which the TV set is Riborced when
main unit for next error.
connecting it with HDMI/DVI.
U705 HDMI/DVI SRM disk
It is generated at the time of it is time
Press [ STOP] on
falsification check
when illegal the SRM data of the
main unit for next error.
error
reproducing disk (verify error), when
connecting it with HDMI/DVI.
connecting it with HDMI/DVI.
F740 HDMI device key
I2C error when writing HDMI Key
Press [ STOP] on
device into transmitter.
main unit for next error.
F893 FLASH ROM IC data Firmware error, DV5 LSI IC (IC8651)
Press [ STOP] on
falsification error
error.
main unit for next error.
F894 EEPROM IC
When failing in the access to
Press [ STOP] on
abnormality error
EEPROM IC located in the DVD
main unit for next error.
Module P.C.B. (IC8611)
F895 Language area
Firmware version agreement check for
Press [ STOP] on
abnormal
factory preset setting failure
main unit for next error.
prevention.
F896 No existence model
Firmware version agreement check for
Press [ STOP] on
factory preset setting failure
main unit for next error.
prevention.
F897 Initialization
Incomplete initialization after writing of
Press [ STOP] on
error
new firmware (Factory preset setting
main unit for next error.
failure prevention)
F898 Disagreement of
Unsuitable combination of AV Decoder,
Press [ STOP] on
hardware and
SDRAM & FLASH ROM IC (firmware).
main unit for next error.
software
F899 The communication
Unsuitable combination of number of
Press [ STOP] on
specification
system com and panel com used.
main unit for next error.
disagreement
(Frimware)
between
micro-processor
micro-processor
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
37
SA-VK860EE
9.4.2. Mechanism Error Code Table
Error
Code
H01 Tray loading error
The tray opening and closing is
Press [ STOP] on
abnormal. CLOSE and OPEN of the
main unit for next error.
tray cannot be carried out properly.
(OPEN time: OPEN
Loading motor error, DV5 LSI IC
CLOSE OPEN
(IC8001) error.
H01 at CLOSE: CLOSE
OPEN CLOSE
H01)
OPEN CLOSE
H01)
H02 Spindle servo error
The spindle servo/motor is abnormal.
Press [ STOP] on
The FG pulse is abnormal. CLV servo
main unit for next error.
error.
H03 Traverse servo error The traverse is abnormal. (Traverse
Press [ STOP] on
servo, DV5 LSI IC (IC8001), TRV
main unit for next error.
motor error.)
H04 Tracking servo error Tracking coil NG (OPU unit
Press [ STOP] on
abnormal), DV5 LSI IC (IC8001)
main unit for next error.
error.
H05 Seek time out error
It is not possible to access the disc.
Press [ STOP] on
TOC cannot read. Abnormal disc etc.
main unit for next error.
Pickup abnormal or disk is dirty.
(TRV motor error, DV5 LSI IC
(IC8001) error.)
(TRV motor error, DV5 LSI IC
(IC8001) error.)
H07 Driver IC thermal
The spindle motor is abnormal. (short
Press [ STOP] on
shut down
between brushes)
main unit for next error.
H15 Disc tray open
The disc tray cannot be opened & it
Press [ STOP] on
detection switch
closes spontaneously.
main unit for next error.
failure
H16 Disc tray close
The disc tray cannot be closed & it
Press [ STOP] on
detection switch
opens spontaneously.
main unit for next error.
failure
U11 Focus servo error
Focus coil, FE signal error.
Press [ STOP] on
main unit for next error.
(Unfinalized DVD-R
main unit for next error.
(Unfinalized DVD-R
U15 Unfinalized DVD-R
is likely to beocme U11.)
F500 DSC error
DV5 LSI IC (IC8001) stops in the
Press [ STOP] on
occurance of servo error (startup,
main unit for next error.
focus error, etc)
F506 Invalid media
Disc is flipped over, TOC unreadable,
Press [ STOP] on
incompatible disc.
main unit for next error.
F620 OPU unit
Laser protection at high temperature.
Press [ STOP] on
abnormality
main unit for next error.
temperature
F621 OPU unit
Laser protection at circuit failure.
Press [ STOP] on
circuitry
main unit for next error.
temperature
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
38
SA-VK860EE
9.4.3. Power Supply Error Code Table
Error
Code
F61 The abnormalities
In normal operation, when DCDET2
Press [ STOP] on
in an output or power
goes to "L" (Low) (Not during POWER
main unit for next error.
supply circuit of
OFF condition), F61 appears on FL
POWER AMP
Display and PCONT goes to "L" (Low).
This is due to speaker output has DC
voltage or fan is not working.
This is due to speaker output has DC
voltage or fan is not working.
F76 Abnormality in the
In normal operation when DCDET1 is
Press [ STOP] on
output voltage of
detected "L" (Low) for two consecutive
main unit for next error.
stabilized power
times, F76 is displayed on FL for 2
supply
seconds and after that PCONT will be
turned to "L" (Low). This is due to any of
the DC voltages (+9V, +7V, -7V, +5V,
+5.3V etc.) not available.
turned to "L" (Low). This is due to any of
the DC voltages (+9V, +7V, -7V, +5V,
+5.3V etc.) not available.
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
9.4.4. ECC Error Code Table
Error
Code
F600 Administrative
It becomes impossible NaviPack etc.
Press [ STOP] on
information cannot
were done, and not to be able to
main unit for next error.
be acquired by the
acquire necessary information in the
recovery error.
navigation’s changing due to wound
etc. of DISC, and to have done the
reproduction transition.
etc. of DISC, and to have done the
reproduction transition.
F601 Irregular sector ID
It tried to access the position that did
Press [ STOP] on
was demanded.
not exist on DISC by the recording
main unit for next error.
error etc. of authoring.
F603 KEYDET cannot be The data for decoding copyright
Press [ STOP] on
acquired by the
protection (CSS) cannot be acquired
main unit for next error.
recovery error.
due to wound etc. of DISC, and it is not
possible to reproduce.
possible to reproduce.
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
39
SA-VK860EE
9.4.5. USB Error Code Table
Error
Code
F650 USB device: Devices Devices other than the mass storage
Press [ STOP] on
other than mass
class are connected.
main unit for next error.
storage
F651 USB device: Non-
The device that the transfer rate did not
Press [ STOP] on
Full Speed Device
correspond to Full Speed was
main unit for next error.
connected.
F652 USB device:
The device in the interface (subclass)
Press [ STOP] on
Interface NG
outside correspondence was
main unit for next error.
connected. (correspondence interface)
001b: Reduced Block Commands
(RBC)
010b: SFF-8020i. MMC-2 (ATAPI)
110b: SCSI transparent command set.
001b: Reduced Block Commands
(RBC)
010b: SFF-8020i. MMC-2 (ATAPI)
110b: SCSI transparent command set.
F655 USB device:
The overcurrent of 500mA or more was
Press [ STOP] on
Overcurrent
detected in VDD USB, and the USB
main unit for next error.
detection
device driver function was intercepted.
(To intercept the current.)
(To intercept the current.)
Diagnosis Contents
Description of error
Automatic FL Display
Remarks
40
SA-VK860EE
Click on the first or last page to see other SA-VK860EE service manuals if exist.