Panasonic SA-PT170EE / SC-PT170EE Service Manual ▷ View online
41
7.1.3.3.
Power Amplifier IC Configuration
Table 1
PT170EE-K
Pin (2)
Front Right
IC5100
Pin (12)
Front Left
Pin (2)
Surround
Right
IC5200
Pin (12)
Surround
Left
Pin (2)
Sub-Woofer +
IC5300
Pin (4)
Sub-Woofer -
Pin (12)
Center +
Pin (10)
Center -
42
7.2.
Basic Troubleshooting Guide for Traverse Unit (DVD Module P.C.B.)
Problems
Checking Points
Checking components
b) Check video signals (Y,C)
LB8301, R8321, R8323,
LB8302, R8325, R8327
LB8302, R8325, R8327
a) Check SDRAM address, data
bus, CLK and other control signals
waveform
bus, CLK and other control signals
waveform
IC8051
1) Distorted picture or
abnormal sound is head
during the initialization
abnormal sound is head
during the initialization
c) Check audio DAC circuitry
* Compare the above with
OK condition DVD Module
P.C.B
OK condition DVD Module
P.C.B
IC8421 (Pin 9 to 11 & 17 to 22)
LB8425, LB8426, LB8427,
LB8428, LB8429, LB8431
*Check for solder short and/or
component missing/damaged
LB8428, LB8429, LB8431
*Check for solder short and/or
component missing/damaged
b) Check laser drive circuitry
(Voltages & current)
(Voltages & current)
Q8551, Q8552 (For DVD),
Q8561, Q8562 (For CD)
Q8561, Q8562 (For CD)
a) Check motor driver circuitry
(+5V)
(+5V)
IC8251 Pin 8, 21
2) No TOC/Long TOC
c) Check LSI IC connection to
motor drive circuitry
* Compare the above with OK
condition DVD Module P.C.B.
* Compare the above with OK
condition DVD Module P.C.B.
IC8001 Pin 66, 67
IC8251 Pin 15 to 16
* Check for solder short and/or
component missing/damaged
IC8251 Pin 15 to 16
* Check for solder short and/or
component missing/damaged
a) Check connection from
DVD Module to Traverse unit
DVD Module to Traverse unit
FP8251
3) Disc not spinning
4) Traverse not moving
5) Traverse and spindle
abnormal movement
4) Traverse not moving
5) Traverse and spindle
abnormal movement
b) Check motor driver circuitry on
the voltages and control signals
the voltages and control signals
* Compare the above with
OK condition DVD Module P.C.B.
OK condition DVD Module P.C.B.
IC8251
* Check for solder short and/or
component damaged
component damaged
6) Cannot read the disc but
spindle motor is spinning
spindle motor is spinning
- Cannot read CD/DVD
a) Check laser drive circuitry
(voltages and current)
(voltages and current)
- Check CD Laser Drive
- Check DVD Laser Drive
* Check voltages and LD current
and compare with OK condition
DVD Module P.C.B.
Q8551, Q8552, LB8551
(For DVD Laser Drive current)
Q8561, Q8562, LB8561
(For CD Laser Drive current)
(For DVD Laser Drive current)
Q8561, Q8562, LB8561
(For CD Laser Drive current)
7) Block Noise during play
a) Check SDRAM address and
data bus signal
IC8051
8) Jitter out of specification
a) Check LD current
b) Check OPU (Change to other
unit and confirmed operating
condition)
unit and confirmed operating
condition)
OPU Unit (Traverse unit), FPC
connection (FP8531 & FP8251)
connection (FP8531 & FP8251)
43
7.3.
Basic Troubleshooting Guide for HDMI AV Output
Problems
Checking Points
Checking components
1) Check setting of the set in
Setup Menu whether the HDMI
Video output is turned ON
Setup Menu whether the HDMI
Video output is turned ON
* This year HDMI always ON.
No need check Setup Menu.
If no resolution selection GUI, then
only check SETUP.
2) +5V Supply to the TV
IC3952 (Pin 4)
3) HDMI Connector Solderability
condition
condition
P3901
4) HDMI Output TDMS signal
lines (IC3901)
lines (IC3901)
- Data (TX0P/M => 14, 16)
- Data (TX1P/M => 18, 20)
- Data (TX2P/M => Pin 22, 24)
- Clock (TXCP/TXCM =>
Pin 10, 12)
Pin 10, 12)
L3905
L3904
L3903
L3906
- Data, SDA (Pin 120, IC3901)
- Clock, SCL (Pin 121, IC3901)
5) HDMI Transmitter
communication lines to TV
communication lines to TV
6) HDMI Transmitter
communication from LSI (IC8001)
(I2C_SCL/I2C_SDA signals)
communication from LSI (IC8001)
(I2C_SCL/I2C_SDA signals)
7) Local Port Slave Address
setting resistor at Pin 99 of HDMI
Transmitter LSI IC (IC3901) for
LPSA signal
setting resistor at Pin 99 of HDMI
Transmitter LSI IC (IC3901) for
LPSA signal
8) HDMI Transmitter LSI IC
(IC3901) +3.3V Supply
(IC3901) +3.3V Supply
9) HDMI Transmitter LSI IC
(IC3901) +1.2V Supply
(IC3901) +1.2V Supply
10) HDMI Up-Con +3.3V Supply
12) Up-Con IC I2C Data and
Clock Line
Clock Line
LB3905, R3905, Q3902, R3904
LB3904, R3907, Q3903, R3906
RX3901
R3921
LB3901, LB3902, IC3901
(Pin 9, 13, 17, 21, 25, 124)
(Pin 9, 13, 17, 21, 25, 124)
IC3901 (Pin 5, 26, 42, 47, 55, 75,
85, 102, 109, 116, 123), LB3908,
IC8151 (Pin 4), LB8001, IC8001
(Pin 20, 44, 83, 158, 187, 211)
85, 102, 109, 116, 123), LB3908,
IC8151 (Pin 4), LB8001, IC8001
(Pin 20, 44, 83, 158, 187, 211)
1) TV does not have any
display. Set FL display
shows U702/U703
display. Set FL display
shows U702/U703
LB3901
11) HDMI Pixel Clock Output from
Up-Con to HDMI Transmitter
(VCLK)
Up-Con to HDMI Transmitter
(VCLK)
LB8901
RX3901
44
Problems
Checking Points
Checking components
13) Hot-Plug Signal
14) TDMS Output swing amplitude
control resistor
control resistor
LB3906, R3902, R3903, Q3901,
D3901
D3901
R3901
15) Host Interface External Input
Clock from LSI (IC8001) to
Up-Con IC (IC3901) - OSC27M
Clock from LSI (IC8001) to
Up-Con IC (IC3901) - OSC27M
LB8702
16) Video Data Lines from LSI
(IC8001) to Up-Con (IC3901)
(IC8001) to Up-Con (IC3901)
RX3707, RX3708, IC3901
(Pin 92 to 95, Pin 87 to 90)
(Pin 92 to 95, Pin 87 to 90)
1) Supply for Up-Con (IC3901)
- Pin 9,124
2) GND for Up-Con
- Pin 7,125
3) Check for capacitor short to
GND
- Pin 9,124
2) GND for Up-Con
- Pin 7,125
3) Check for capacitor short to
GND
LB3902
1) Check digital video data line
from LSI(IC8001) to Up-Converter
(IC3901), VOUT0-VOUT7.
from LSI(IC8001) to Up-Converter
(IC3901), VOUT0-VOUT7.
RX3707, RX3708
C3902, C3928, C3925
1) TV does not have any
display. Set FL display
shows U702/U703
display. Set FL display
shows U702/U703
2) When switching the video
output mode from 480P to
720p/1080i, TV display
becomes blank
output mode from 480P to
720p/1080i, TV display
becomes blank
3) Color Problem. TV Screen
is White/Blue/Purple
is White/Blue/Purple
1) Audio data lines
2) Check setting of the set in
Setup Menu whether the HDMI
Audio output is turned On
Setup Menu whether the HDMI
Audio output is turned On
R8402, RX8402
* Check for solder short and/or
component missing/damaged
as well as signal condition.
component missing/damaged
as well as signal condition.
4) HDMI got no audio output
Click on the first or last page to see other SA-PT170EE / SC-PT170EE service manuals if exist.