DOWNLOAD Panasonic SA-PT170EE / SC-PT170EE Service Manual ↓ Size: 6.81 MB | Pages: 127 in PDF or view online for FREE

53

Step 2 Move the shaft (R) of the DVD lid in the direction of
arrow (1) & (2).
Step 3 Lift the door spring of shaft (L) in the direction of arrow
(3).
Step 4 Move the shaft (L) of the DVD Lid in the direction of
arrow (4).
Step 5 Remove the DVD lid in the direction of arrow.

• Follow (Step 1) to (Step 3) of Item 9.3.

 

Step 1 Remove 1 screw at the rear panel.

Step 2 Remove 2 screws on AC Inlet P.C.B.
Step 3 Remove the P.C.B. bracket.
Caution: Keep the AC Inlet shield plate unit in safe place. 
Avoid denting it. Place it back during assembling.

Caution: Keep the P.C.B. bracket in safe place. Avoid dent-
ing it. Place it back during assembling.
Step 4 Use plier to release the AC Inlet P.C.B. Spacer.
Step 5 Desolder Black (TL20) & Red (TL19) wires on AC Inlet
P.C.B..
Step 6 Remove AC Inlet P.C.B.

54

• Follow (Step 1) to (Step 3) of Item 9.3.
• Follow (Step 1) to (Step 3) of Item 9.6.
• Follow (Step 7) to (Step 9) of Item 9.6.

 

Step 1 Slightly move the Main P.C.B up as diagram shown.
Step 2 Detach 14P cable at the connector (CN2016) on the
SMPS P.C.B.
Step 3 Detach 8P cable at the connector (CN2017) on the
SMPS P.C.B.

Step 4 Lift up the Main P.C.B as diagram shown.
Step 5 Detach 50P FFC at the connector (CN2001) on the
Main P.C.B.
Step 6 Detach 17P FFC at the connector (CN2009) on the
Main P.C.B.
Step 7 Remove Main P.C.B.

55

• Follow (Step 1) to (Step 3) of Item 9.3.
• Follow (Step 1) to (Step 3) of Item 9.6.
• Follow (Step 7) to (Step 10) of Item 9.6.

Step 1 Remove 1 screw at the rear panel.

Step 2 Remove 1 screw at the P.C.B bracket.
Step 3 Remove P.C.B bracket.
Caution: Keep the P.C.B. bracket in safe place. Avoid dent-
ing it. Place it back during assembling.
 

Step 4 Move aside Main P.C.B. and position it according to the

56

diagram shown.
Step 5 Remove 3 screws on Analog Amp P.C.B.
Step 6 Detach 17P FFC at the connector (CN5050) on Analog
Amp P.C.B.
Step 7 Detach 4P cable at the connector (CN5051) on Analog
Amp P.C.B.
Step 8 Twist the wire clamper to detach 3P cable at the con-
nector (CN5704) on Analog Amp P.C.B.

Step 9 Remove 2 screws at the rear panel.
Step 10 Release the tab of the rear panel in the direction of
arrow.
Step 11 Remove Analog Amp P.C.B.

• Follow (Step 1) to (Step 3) of Item 9.3.
• Follow (Step 1) to (Step 3) of Item 9.6.
• Follow (Step 7) to (Step 10) of Item 9.6.
• Follow (Step 1) to (Step 11) of Item 9.13.

 

Step 1 Desolder pins of the 2CH BTL Power Amplifier IC
(IC5100) on the solder side of Analog Amp P.C.B.