LG JUPITERCUT Service Manual ▷ View online
Error Mode
TROUBLESHOOTING
9
21
TROUBLESHOOTING
9
Error Mode
Display
symptom
Check point
-.Fire detection of drum through
low thermistor temp detecting.
-.Low Thermistor Open/Short
Error.
low thermistor temp detecting.
-.Low Thermistor Open/Short
Error.
-.Filter is not replaced.
-.Dryer does not work
-.Dryer does not work
1) Connector
→ not assembled?- Open
Check weather connector in connected correct or not?
2) If the covering has been peeled away or touch? - Short
If the penetration of water? - Short
Check if any damage in harness or not?
3) Thermistor element
2) If the covering has been peeled away or touch? - Short
If the penetration of water? - Short
Check if any damage in harness or not?
3) Thermistor element
→ dead
Check if thermistor resistance in normal or not?
4) Check the voltage from main PCB to thermistor
High or low voltage?
4) Check the voltage from main PCB to thermistor
High or low voltage?
→ Replace Main PCB
* See page No.17
* Thermistor Resistance : 10k
* Thermistor Resistance : 10k
Ω±5% at 25℃
1.Check the filter is properly seated.
2.Check the magnet in filter.
3.Check the Reed switch is normal or not.
2.Check the magnet in filter.
3.Check the Reed switch is normal or not.
22
TROUBLESHOOTING
9
23
NO
Power-On
Power-Off
Press Power button
LED
–Segment
On
Press Start/Pause button
Drum not
Roating
Door Open?
Lamp on?
Lamp Broken
Connector malfunction
Connector malfunction
Start button Lock:
: No buzzer
: No buzzer
Plugged in
Low voltage
LED broken,
connector malfunction.
connector malfunction.
Low temperature
Circuit breaker
trip
trip
Power button
Lock:No buzzer
Lock:No buzzer
Harness Wire
broken
broken
Display pcb wire broken,
not connected
not connected
Replace Belt
Clean Filter or
Check the Eva
Clogging
Empty water
container
container
Drum Belt broken
Clean Filter sign
display
display
Empty water sign
display
display
Reduce clothes load,
Spin the load more
Spin the load more
Check motor TP Trip,
Check blower damage
(locking)
Door is not closed
(" ") display
(" ") display
Insert Filter sign
display
display
See the Page 24
check list
check list
Check the magnet,
Replace the Filter
Replace the Filter
Properly
Drying?
(Dryness level
& Time)
LQC Mode 1
Check LEV
Check LEV
Check Heater Power
Check Comp Power
Check Comp OLP Trip
Check Thermostat Trip
Speed Mode
Check surrounding Temp.
of product placed
of product placed
Check LEV failure?
-. Resistance : 46 3.7 (20¡C)
-. Housing connection
-. Initial Eva in Temp. Drop
-. Resistance : 46 3.7 (20¡C)
-. Housing connection
-. Initial Eva in Temp. Drop
DIAGNOSTIC TEST
10
Test 1 : ELECTRIC SUPPLY & CONTROL CHECK
Trouble Symptom : No power to the dryer or the controller
Measurement condition : Power is on.
[ Caution] Electric shock. Please test after grounding check.
Power voltage is within
standard range
(AC 215V~245V)?
standard range
(AC 215V~245V)?
• Check the
- Circuit breaker
• Check after disconnecting
Yellow relay and Black relay
connector of Main PCB.
connector of Main PCB.
• Check the range of Blue and
Brown wire is within AC 215
~245V?
~245V?
• Check the short of
harness assembly and
the connection.
the connection.
• Check or replace the Power
cord.
• Check or replace the Noise
filter.
• Check or replace the
Controller.
24
Click on the first or last page to see other JUPITERCUT service manuals if exist.