DOWNLOAD JBL SUB 140 (serv.man2) Service Manual ↓ Size: 6.45 MB | Pages: 73 in PDF or view online for FREE

 

Page 18 of 54 

Report No.: 1009940 

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

15.3.8 

Terminals carrying a current more than 0.2A contact 
pressure not transmitted by insulating material 
except ceramic  

 N/A 

15.3.9 Termination 

of 

non-detachable cords/wires 

terminated near to each other  

 P 

 

Terminals located and shielded: test with 8 mm 
strand  

 P 

15.4 

15.4.1 

No undue strain on mains socket-outlets  

 

N/A 

15.4.2 

Device complies with standard for dimensions of 
mains plugs  

 N/A 

15.4.3 

Device has adequate mechanical strength 
(tests a, b, c)  

 N/A 

 

16.1 

Mains cords sheathed type, complying with 
IEC 60227 for PVC or IEC 60245 for synthetic 
rubber cords …………………………………….: 

PVC P 

 

Non-detachable cords for Class I have green/yellow 
core for protective earth  

 N/A 

16.2 

Mains cords conductors have adequate cross-
sectional area for rated current consumption of the 
equipment  

2 x 0.75mm² 

P 

16.3 

a) Flexible cords not complying with 16.1, used for 
interconnections between separate units of 
equipment used in combination and carrying 
hazardous live voltages, have adequate dielectric 
strength  

 N/A 

 

b) Flexible cords not complying with 16.1, withstand 
bending and mechanical stress (3.2 of IEC 60227-2) 

 N/A 

16.4 

Flexible cords used for connection between 
equipment have adequate cross-sectional areas to 
avoid temperature rise under normal and fault 
conditions  

 N/A 

16.5 

Adequate strain relief on external flexible cords  

Strain relief bushing under 
compression 

P 

 

Not possible to push cord back into equipment  

 

P 

 

Strain relief device unlikely to damage flexible  
cord  

 P 

 

For mains cords of Class I equipment, hazardous 
live conductors become taut before earth conductor  

 N/A 

 

Page 19 of 54 

Report No.: 1009940 

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

16.6 

Apertures for external flexible cord: no risk of 
damage to the cord during assembly or movement in 
use  

 P 

16.7 

Transportable musical instruments and amplifiers 
fitted with detachable cord set with appliance inlet to 
IEC 60320-1  

 N/A 

 

Transportable musical instruments and amplifiers 
fitted with detachable cord sets or with means of 
stowage to protect the cord  

 N/A 

 

17.1 

 

- screws into metal: 5 times  

 

N/A 

 

- screws into non-metallic material: 10 times  

3.6 x 15.5mm, 1.2N 
4.1 x 19.8mm, 1.2N 

P 

17.2 

Correct introduction into female threads in non-
metallic material  

 P 

17.3 

Cover fixing screws: captive  

 

N/A 

 

Non-captive fixing screws: no hazard when replaced 
by a screw whose length is 10 times its diameter  

 P 

17.4 

No loosening of conductive parts carrying a current 
> 0.2A  

 N/A 

17.5 

Contact pressure not transmitted through plastic 
other than ceramic for connections carrying a current 
> 0.2A  

 N/A 

17.6 

Stranded conductors of flexible supply cords carrying 
a current > 0.2A with screw terminals not 
consolidated by solder  

 N/A 

17.7 

Cover fixing devices other than screws have 
adequate strength and their positioning is 
unambiguous  

 N/A 

17.8 

Fixing devices for detachable legs or stands  
provided  

 N/A 

17.9 

 P 

 

 

Page 20 of 54 

Report No.: 1009940 

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

 

 

Picture tube separately approved to IEC 61965 .: 

 

N/A 

 

Picture tube separately approved to 18.1 ..…….: 

 

N/A 

18.1 

Picture tubes >16cm intrinsically protected  

 

N/A 

 Non-intrinsically 

protected tubes >16cm used with 

protective screen  

 N/A 

 

Protective film as part of implosion protection: edges 
covered by enclosure  

 N/A 

18.2 

18.2.1 

Samples subject to ageing: 6 samples  

 

N/A 

18.2.2 

Samples subject to implosion test: 6 samples  

 

N/A 

18.2.3 

Samples subject to mechanical strength test (steel 
ball): 6 samples  

 N/A 

18.3 Non-intrinsically 

protected tubes tested to 18.3  

 

N/A 

 

 

Mass of the equipment exceeding 7kg ..………….: 

 

P 

 

Apparatus intended to be fastened in place – 
suitable instructions ……………………….….: 

 N/A 

19.1 

Test on a plane, inclined at 10

o

 to the horizontal  

 

P 

19.2 

100N force applied vertically downwards  

 

P 

19.3 

100N force, or 13% of weight, applied horizontally to 
point of least stability  

 N/A 

19.4 

Edges or corners not hazardous  

 

P 

19.5 

Glass surfaces (exc.laminated) with an area 
exceeding 0.1m² or maximum dimension > 450mm, 
pass the test of 19.5.1  

 N/A 

19.6 

Wall or ceiling mountings adequate  

 

N/A 

 

 

Page 21 of 54 

Report No.: 1009940 

Clause 

Requirement + Test 

Result - Remark 

Verdict 

 

 
TRF No. IEC60065J 

 

20.1 

 

a) Exemption for components contained in an 
enclosure of material V-0 to IEC 60695-11-10 with 
openings not exceeding 1mm in width  

 N/A 

 

b) Exemption for small components as defined in 
20.1  

 P 

20.1.1 Electrical 

components 

meet the requirements of 

Clause 14 or 20.1.4  

 P 

20.1.2 

Insulation of internal wiring working at voltages >4kV 
or leaving an internal fire enclosure, or located within 
the areas mentioned in Table 21, not contributing to 
the spread of fire  

 N/A 

20.1.3 

Material of printed circuit boards on which the 
available power exceeds 15W at a voltage between 
50V and 400V (peak) a.c. or d.c. meets V-1 or better 
to IEC 60707, unless used in a fire enclosure  

 P 

 

Material of printed circuit boards on which the 
available power exceeds 15W at a voltage >400V 
(peak) a.c. or d.c. meets V-0 to IEC 60707  

 N/A 

20.1.4 

Components and parts not covered by 20.1.1, 20.1.2 
and 20.1.3 (other than fire enclosures) mounted 
nearer to a potential ignition source than the 
distances in Table 21 comply with the relevant 
flammability category in Table 21  

(see appended table) 

P 

 

Components and parts as above but shielded from a 
potential ignition source, with the barrier area in 
accordance with Table 21 and fig. 13  

 N/A 

 

Apparatus with voltages >4kV under normal 
operating conditions and distances to the enclosure 
exceed those specified Table 21, flammability 
classification HB40 or better is required for the 
enclosure  

 N/A 

20.2 

20.2.1 

Potential ignition sources with open circuit voltage 
> 4kV (peak) a.c. or d.c. contained in a fire enclosure 
to V-1  

 N/A 

20.2.2 

 N/A 

20.2.3 

Requirements of 20.2.1 and 20.2.2 met by an 
internal fire enclosure  

 N/A