JBL SB 100 (serv.man3) EMC - CB Certificate ▷ View online
Page 61 of 68
Report No.: 350-120154AX
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
National Differences – Japan, J60065 (H23)
7.1.5
Add the following paragraph as 2
nd
paragraph of
Condition “d “in Table 3.
For materials which are not listed in Table 3,
temperature rises in the normal operating
conditions are considered satisfactory if these
materials comply with item 3 of detailed
regulations, 1.(1),b, Appendix 4 in the Ministerial
Ordinance on stipulating technical requirements for
the Electrical Appliance and Material. Permissible
temperature rise of “Supply cords and wiring
insulation” is applicable only to the materials used
in supply cords complying with JIS C 3662
(corresponding to IEC 60227) or JIS C 3663
(corresponding to IEC 60245). Materials used in
other wiring shall comply with item 3 of detailed
regulations, 1.(1).b, Appendix 4 in the Ministerial
Ordinance on stipulating technical requirements for
the Electrical Appliance and Material.
For materials which are not listed in Table 3,
temperature rises in the normal operating
conditions are considered satisfactory if these
materials comply with item 3 of detailed
regulations, 1.(1),b, Appendix 4 in the Ministerial
Ordinance on stipulating technical requirements for
the Electrical Appliance and Material. Permissible
temperature rise of “Supply cords and wiring
insulation” is applicable only to the materials used
in supply cords complying with JIS C 3662
(corresponding to IEC 60227) or JIS C 3663
(corresponding to IEC 60245). Materials used in
other wiring shall comply with item 3 of detailed
regulations, 1.(1).b, Appendix 4 in the Ministerial
Ordinance on stipulating technical requirements for
the Electrical Appliance and Material.
Pass
7.1.5
In the first paragraph of Condition “f” of Table 3,
add ”JIS K 7206:1999 or” before the reference,
ISO 306.
add ”JIS K 7206:1999 or” before the reference,
ISO 306.
Pass
7.1.5
In Condition “f,” 1) of Table 3, add ”JIS K
7206:1999 or” before the reference, ISO 306.
7206:1999 or” before the reference, ISO 306.
Pass
7.2
In NOTE 2, add “or JIS standard (identical to or
modified IEC)” after the word, IEC standard.
modified IEC)” after the word, IEC standard.
N/A
8.5
In the first paragraph, add “and Class 0I
Equipment” after the words, Class I Equipment.
Equipment” after the words, Class I Equipment.
N/A
8.5
In the six paragraph (before NOTE 3), add the
following to the end of the first sentence.
CLASS 0I EQUIPMENT shall be provided with a
protective earthing terminal at any point outside
the apparatus where easily visible or a protective
external earth wire from mains plug.
following to the end of the first sentence.
CLASS 0I EQUIPMENT shall be provided with a
protective earthing terminal at any point outside
the apparatus where easily visible or a protective
external earth wire from mains plug.
N/A
8.11
In NOTE 2, c), add “or JIS C 2107, JIS C 2336, JIS
C 2338” after the reference, IEC 60454.
C 2338” after the reference, IEC 60454.
N/A
9.1.1.1
In the last paragraph, add the following sentence
after the first sentence.
For CLASS 0I EQUIPMENT, the r.m.s. TOUCH-
CURRENT to earth shall not be more than 1.0 mA.
after the first sentence.
For CLASS 0I EQUIPMENT, the r.m.s. TOUCH-
CURRENT to earth shall not be more than 1.0 mA.
N/A
10
In NOTE, replace “IEC 60664-1 and IEC 60664-4
[9]” by “JIS C 0664:2003 and IEC/TR3 60664-4 [8]”
[9]” by “JIS C 0664:2003 and IEC/TR3 60664-4 [8]”
Pass
10.1
Add “CLASS 0I EQUIPMENT and” to the head of
the first paragraph.
the first paragraph.
N/A
Page 62 of 68
Report No.: 350-120154AX
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
In Table 5, add the following values to the sub-
table of NOTE.
table of NOTE.
Test voltage (peak)
Operating
Voltage U
(peak)
Curve A Curve B
142 V
1 414 V
2 828 V
10.3.2
See appended table
CL.10.3.
CL.10.3.
Pass
11.2.1
Add the following after the original NOTE.
NOTE 2 Fuses except for the ones according to
IEC 60127 shall be tested in consideration of the
characteristic.
NOTE 2 Fuses except for the ones according to
IEC 60127 shall be tested in consideration of the
characteristic.
See appended table
CL.11.2.
CL.11.2.
Pass
11.2.3
Add “and CLASS 0I” after the words, CLASS I.
N/A
13.4
In NOTE 2 of Table 11, replace IEC 60664-1 by
JIS C 0664:2003 (corresponding to IEC 60664-1).
JIS C 0664:2003 (corresponding to IEC 60664-1).
See appended table
CL.11.2.
CL.11.2.
Pass
14.3.3.2
In the second sentence of the first paragraph, add
“or JIS C 2107, JIS C 2336 and JIS C 2338” after
the reference, IEC 60454.
“or JIS C 2107, JIS C 2336 and JIS C 2338” after
the reference, IEC 60454.
N/A
14.5.1.1
In item a), add “JIS C 9730 series or” before the
reference, IEC 60730 series.
reference, IEC 60730 series.
N/A
14.5.1.2
In the first sentence of item a), replace “IEC
60691” by “IEC 60691, JIS C 6691:2003 or
Appendix 3 of the Ministerial Ordinance on
stipulating technical requirements for the Electrical
Appliance and Material”.
60691” by “IEC 60691, JIS C 6691:2003 or
Appendix 3 of the Ministerial Ordinance on
stipulating technical requirements for the Electrical
Appliance and Material”.
N/A
14.5.1.2
After the second sentence of item a), replace “IEC
60691” by “JIS C 6691:2003 or IEC 60691”.
60691” by “JIS C 6691:2003 or IEC 60691”.
N/A
14.5.2.1
Replace the first and the second sentence as
follows:
Fuse-links, DIRECTLY CONNECTED TO THE
MAINS, used in order to prevent the apparatus
from becoming unsafe within the sense of this
standard shall comply with
- the relevant part of IEC 60127 or JIS C 6575,
unless they have a rated current outside the range
specified in that standard. In the latter case, they
shall comply with the relevant part of IEC 60127 or
JIS C 6575 as far as applicable, or
- Appendix 3 of the Ministerial Ordinance on
stipulating technical requirements for the Electrical
Appliance and Material (limited to Fuses with the
rated current of 1 A or more).
follows:
Fuse-links, DIRECTLY CONNECTED TO THE
MAINS, used in order to prevent the apparatus
from becoming unsafe within the sense of this
standard shall comply with
- the relevant part of IEC 60127 or JIS C 6575,
unless they have a rated current outside the range
specified in that standard. In the latter case, they
shall comply with the relevant part of IEC 60127 or
JIS C 6575 as far as applicable, or
- Appendix 3 of the Ministerial Ordinance on
stipulating technical requirements for the Electrical
Appliance and Material (limited to Fuses with the
rated current of 1 A or more).
See appended table CL.14.
Pass
Page 63 of 68
Report No.: 350-120154AX
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
14.5.2.2
Add the following sentence before the last
paragraph.
For Fuses according to Appendix 3 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance and
Material, all that needs to be marked is the rated
current.
paragraph.
For Fuses according to Appendix 3 of the
Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance and
Material, all that needs to be marked is the rated
current.
N/A
14.5.3
Replace IEC 60730-1 by JIS C 9730-1
(corresponding to IEC 60730-1).
(corresponding to IEC 60730-1).
N/A
14.5.4
Replace IEC 60127 by “IEC 60127 or JIS C 6575”.
N/A
14.6.1
Add the following paragraph after NOTE.
The following manually operated mechanical
switches shall meet the requirements specified in
item a) or b) below.
- the controlling current exceeds 0.2 A r.m.s a.c.
The following manually operated mechanical
switches shall meet the requirements specified in
item a) or b) below.
- the controlling current exceeds 0.2 A r.m.s a.c.
or d.c.
- the voltage across the open switch contacts
exceeds 35 Vpeak ac or 24 Vdc.
N/A
14.6.1
In item a), replace IEC 61058-1 by “IEC 61058-1 or
JIS C 4526-1:1999”.
JIS C 4526-1:1999”.
N/A
14.6.2
In item a), replace IEC 61058-1 by “IEC 61058-1 or
JIS C 4526-1:1999”.
JIS C 4526-1:1999”.
N/A
14.6.3
In item a), replace IEC 61058-1 by “IEC 61058-1 or
JIS C 4526-1:1999”.
JIS C 4526-1:1999”.
N/A
14.6.5
In item a), replace IEC 61058-1 by “IEC 61058-1 or
JIS C 4526-1:1999”.
JIS C 4526-1:1999”.
N/A
14.7
Replace IEC 60950 by JIS C 6950:2006.
N/A
Page 64 of 68
Report No.: 350-120154AX
IEC 60065
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
15.1.1
Replace the first and second paragraph by the
following.
Plugs and appliance couplers for the connection of
the apparatus to the MAINS and socket-outlets
and interconnection couplers for providing MAINS
power to other apparatus shall comply with the
relevant JIS standards for plugs, socket-outlets,
appliance couplers or interconnection couplers. If
there is no appropriate JIS standard, they shall
comply with the relevant IEC standards.
Appliance connectors, interconnection outlets and
interconnection plug-connectors compiled with
Appendix 3 of the Ministerial Ordinance on
stipulating technical requirements for the Electrical
Appliance and Material are accepted. In that case,
if due to the shape the contact parts are
connectable to those specified in standard sheets
of IEC 60320-1, they shall comply with dimensions
and ratings specified in the relevant standard
sheets of IEC 60320-1.
Examples of relevant specifications and standards:
- Plugs / Socket-outlets: Appendix 4 of Article 1 of
following.
Plugs and appliance couplers for the connection of
the apparatus to the MAINS and socket-outlets
and interconnection couplers for providing MAINS
power to other apparatus shall comply with the
relevant JIS standards for plugs, socket-outlets,
appliance couplers or interconnection couplers. If
there is no appropriate JIS standard, they shall
comply with the relevant IEC standards.
Appliance connectors, interconnection outlets and
interconnection plug-connectors compiled with
Appendix 3 of the Ministerial Ordinance on
stipulating technical requirements for the Electrical
Appliance and Material are accepted. In that case,
if due to the shape the contact parts are
connectable to those specified in standard sheets
of IEC 60320-1, they shall comply with dimensions
and ratings specified in the relevant standard
sheets of IEC 60320-1.
Examples of relevant specifications and standards:
- Plugs / Socket-outlets: Appendix 4 of Article 1 of
the Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance. Article
2 (corresponding to IEC 60884) of the
Ordinance.
requirements for the Electrical Appliance. Article
2 (corresponding to IEC 60884) of the
Ordinance.
- Appliance couplers: Appendix 4 of Article 1 of
the Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance. Article
2 (corresponding to IEC 60320-1) of the
Ordinance.
requirements for the Electrical Appliance. Article
2 (corresponding to IEC 60320-1) of the
Ordinance.
- Appliance inlets: IEC 60320-1
- Interconnection outlets: Appendix 4 of Article 1 of
- Interconnection outlets: Appendix 4 of Article 1 of
the Ministerial Ordinance on stipulating technical
requirements for the Electrical Appliance. IEC
60320-2-2.
requirements for the Electrical Appliance. IEC
60320-2-2.
- Interconnection couplers: Appendix 4 of Article 1
of the Ministerial Ordinance on stipulating
technical requirements for the Electrical
Appliance.
technical requirements for the Electrical
Appliance.
Delete NOTE 1 and NOTE 2.
See appended table CL.14.
Pass
15.1.1
Replace the paragraph after NOTE 2 by the
following.
MAINS socket-outlets and interconnection
couplers mounted on CLASS 0I and CLASS II
apparatus shall not permit connection of CLASS I
apparatus.
following.
MAINS socket-outlets and interconnection
couplers mounted on CLASS 0I and CLASS II
apparatus shall not permit connection of CLASS I
apparatus.
N/A
Click on the first or last page to see other SB 100 (serv.man3) service manuals if exist.