JBL RADIAL (serv.man5) EMC - CB Certificate ▷ View online
Page 40 of 49
Report No. 152949
IEC
60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
2.5 TABLE:
limited
power
sources
N/A
Circuit output tested:
Measured Uoc (V) with all load circuits
disconnected:
disconnected:
I
sc
(A)
VA
Meas.
Limit
Meas.
Limit
Normal condition
Single fault: …..
supplementary information:
Sc=Short circuit, Oc=Open circuit
2.10.2
Table: working voltage measurement
N/A
Location
RMS voltage (V)
Peak voltage (V) Comments
supplementary information:
Page 41 of 49
Report No. 152949
IEC
60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
2.10.3 and
2.10.4
2.10.4
TABLE: Clearance and creepage distance measurements
N/A
Clearance (cl) and creepage
distance (cr) at/of/between:
distance (cr) at/of/between:
U peak
(V)
U r.m.s.
(V)
Required cl
(mm)
cl
(mm)
Required cr
(mm)
cr
(mm)
Functional:
Basic/supplementary:
Reinforced:
Supplementary information:
2.10.5 TABLE:
Distance
through insulation measurements
N/A
Distance through insulation (DTI) at/of:
U peak
(V)
U rms
(V)
Test
voltage
(V)
Required DTI
(mm)
DTI
(mm)
Supplementary information:
Page 42 of 49
Report No. 152949
IEC
60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
4.3.8 TABLE:
Batteries
N/A
The tests of 4.3.8 are applicable only when appropriate battery
data is not available
data is not available
Is it possible to install the battery in a reverse polarity position?
Non-rechargeable batteries
Rechargeable batteries
Discharging
Un-
intentional
charging
Charging
Discharging
Reversed
charging
Meas.
current
Manuf.
Specs.
Specs.
Meas.
current
Manuf.
Specs.
Specs.
Meas.
current
Manuf.
Specs.
Specs.
Meas.
current
Manuf.
Specs.
Specs.
Max.
current
during
normal
condition
current
during
normal
condition
Max.
current
during
fault
condition
current
during
fault
condition
Test results:
Verdict
- Chemical leaks
N/A
- Explosion of the battery
N/A
- Emission of flame or expulsion of molten metal
N/A
- Electric strength tests of equipment after completion of tests
N/A
Supplementary information:
4.3.8 TABLE:
Batteries
N/A
Battery category .......................................... : (Lithium, NiMh, NiCad, Lithium Ion …)
Manufacturer ............................................... :
Type / model ................................................ :
Voltage ........................................................ :
Capacity ...................................................... : mAh
Tested and Certified by (incl. Ref. No.) ....... :
Circuit protection diagram:
Page 43 of 49
Report No. 152949
IEC
60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60950_1B
MARKINGS AND INSTRUCTIONS (1.7.12, 1.7.15)
Location of replaceable battery
Language(s) …………………………………….:
Close to the battery …………………………….:
In the servicing instructions
……………………:
……………………:
In the operating instructions …………………..:
4.5
TABLE: Thermal requirements
P
Supply voltage (V) .......................... :
24 V dc 24 V dc
⎯
Ambient T
min
(
°C) ............................. :
⎯
Ambient T
max
(
°C) ............................ :
20.6
40.0
⎯
Maximum measured temperature T of part/at::
T (
°C)
Allowed
T
max
(
°C)
(meas)
(max)
—
C53 (rated 105ºC)
46.7
66.1
105
C25 (rated 105ºC)
45.8
65.5
105
C27 (rated 105ºC)
41.4
60.8
105
L4 (105ºC min. materials)
36.5
55.9
105
PCB (other side of U5 & heat sink) (105ºC min.
material)
material)
48.4 67.8
105
Supplementary information:
Normal condition heating with a 24 Vdc input (refer to Test items particulars).
”Max” column is temps adjusted for Tmra of 40°C.
External temperatures on equipment was not recorded, but found to meet temperature requimrents based
off internal measured temperatures on components.
Normal condition heating with a 24 Vdc input (refer to Test items particulars).
”Max” column is temps adjusted for Tmra of 40°C.
External temperatures on equipment was not recorded, but found to meet temperature requimrents based
off internal measured temperatures on components.
Temperature T of winding:
t
1
(°C)
R
1
(
Ω)
t
2
(°C)
R
2
(
Ω)
T (
°C)
Allowed
T
max
(
°C)
Insulatio
n class
Supplementary information:
Rise of Resistance not used.
Rise of Resistance not used.
Click on the first or last page to see other RADIAL (serv.man5) service manuals if exist.