JBL ON STAGE (serv.man3) EMC - CB Certificate ▷ View online
- Page 9 of 19 -
Order No. 23171
1
GENERAL
—
1.1
SCOPE
—
1.1.1
Equipment covered by this
standard
standard
The product is driven by a digital audio signal and is
therefore considered within the scope of IEC 60950.
therefore considered within the scope of IEC 60950.
—
1.1.2
Additional requirements:
—
Exposure to extreme temperatures,
excessive dust, moisture or
vibration; to flammable gases; to
corrosive or explosive atmospheres
excessive dust, moisture or
vibration; to flammable gases; to
corrosive or explosive atmospheres
This equipment is intended to operate in a "normal"
environment (Offices and homes). Max recommended
ambient temperature (T
environment (Offices and homes). Max recommended
ambient temperature (T
MRA
) as stated by the
manufacturer is 25
°
C.
—
Electromedical equipment
connected to the patient
connected to the patient
This equipment is not an electromedical equipment
intended to be physically connected to a patient.
intended to be physically connected to a patient.
—
Equipment used in vehicles, ships
or aircrafts, in tropical countries, or
at elevations > 2000m
or aircrafts, in tropical countries, or
at elevations > 2000m
This equipment is intended to operate in a "normal"
environment (Offices and homes). Max recommended
ambient temperature (T
environment (Offices and homes). Max recommended
ambient temperature (T
MRA
) as stated by the
manufacturer is 25
°
C.
—
Equipment intended for use where
ingress of water is possible
ingress of water is possible
This equipment is intended to be used in applications
where ingress of water is not regarded possible. The
equipment is non-protected according to IEC 60529.
where ingress of water is not regarded possible. The
equipment is non-protected according to IEC 60529.
—
IP-classification (IEC 60529) (IP)
IP X0.
—
1.2.2
OPERATING CONDITIONS
—
1.2.2.1
Normal load as described in Annex
L or as close as possible to the
most severe normal use
L or as close as possible to the
most severe normal use
Max. undistorted with sign wave signal was 16.1 W,
reduce d to 1/8
reduce d to 1/8
th
Max. and switched to filtered pink noise
per IEC/EN 60065 for maximum normal load.
Refer to Summary of Testing.
Refer to Summary of Testing.
—
1.2.2.2
Rated operating time as assigned
by the manufacturer
by the manufacturer
The manufacturer has not declared a rated operating
time.
time.
—
1.2.2.3
Continuous operation
The equipment is regarded to be for continuous
operation.
operation.
—
- Page 10 of 19 -
Order No. 23171
1.5
COMPONENTS
—
1.5.1
General
Refer to List of Critical Components.
P
1.5.2
Evaluation and testing of
components
components
Certified components are used in accordance with their
ratings, certifications and they comply with applicable
parts of this standard.
Components not certified are used in accordance with
their ratings and they comply with applicable parts of
IEC 60950 and the relevant component standard.
Components, for which no relevant IEC-standard exists,
have been tested under the conditions occurring in the
equipment, using applicable parts of IEC 60950.
ratings, certifications and they comply with applicable
parts of this standard.
Components not certified are used in accordance with
their ratings and they comply with applicable parts of
IEC 60950 and the relevant component standard.
Components, for which no relevant IEC-standard exists,
have been tested under the conditions occurring in the
equipment, using applicable parts of IEC 60950.
P
Dimensions of mains plug for direct
plug-in equipment
plug-in equipment
Not intended to plug directly into a wall socket-outlet.
N
1.5.3
Thermal controls
No adjustable thermal controls.
N
1.5.4
Transformers
Class III equipment.
N
1.5.5
Interconnecting cables
The interconnecting cables contain only SELV.
N
1.5.6
Capacitors in primary circuits
Class III equipment.
N
1.5.7.1
- 1.5.7.3 Double or reinforced
insulation bridged by components
insulation bridged by components
Class III equipment.
N
1.5.8
Components in equipment for IT
power systems
power systems
Class III equipment.
N
- Page 11 of 19 -
Order No. 23171
1.5.01
LIST OF CRITICAL COMPONENTS
—
Part No
Component/
Object
Object
Manufacturer
Type / Model
Ratings /
Technical Data
Technical Data
Complies
with the
following
standard
with the
following
standard
Marks of
conformity
granted **)
conformity
granted **)
Enclosure
DOW Emerge
4330 -22
Rated minimum
flame class HB
flame class HB
UL 94
UL
Alternative
Various
Various
UL 94
UL
Jointronics
PVC
30 V, 80ºC
Evaluated
in unit
in unit
UL
Alternative
Various
Various
30 V, 80ºC
UL 94
UL
Various
Various
Rated minimum
flame class V-2
flame class V-2
Evaluated
in unit
in unit
UL
PCB material
Various
Various
Rated minimum
flame class V-1 or
better
flame class V-1 or
better
Evaluated
in unit
in unit
UL
Power
amplifier IC
amplifier IC
ST Microelectronics
TDA2007A
6 W x 6 output
Evaluated
in unit
in unit
None
Speaker (4)
Various
1 inch,
magnetically
shielded
magnetically
shielded
6.8
Ω
Evaluated
in unit
in unit
None
Comments
**)
Marks listed under “Marks of conformity granted” indicates Nemko has verified the respective certifications.
- Page 12 of 19 -
Order No. 23171
1.6
POWER INTERFACE
—
1.6.1
A.C. power distribution systems
TN, and IT for Norway.
—
1.6.2
Input current
1 A
—
Test voltage (at each rated voltage
or at each end of a rated voltage
range)
or at each end of a rated voltage
range)
18 VDC
Measured current
Max current during normal operation 0.58 A @ 18 VDC
P
Deviation
Negative deviation is not limited.
P
1.6.3
Voltage limit of hand-held
equipment (max. 250V)
equipment (max. 250V)
The equipment is not hand-held.
N
1.6.4
Neutral conductor
Class III equipment.
N
1.7
MARKINGS AND INSTRUCTIONS
—
1.7.1
Power rating
The required marking is provided.
P
Rated voltage
18 V (dc symbol from IEC 60417, No. 5031)
Refer to Copy of markings.
Refer to Copy of markings.
P
Symbol for nature of supply for d.c.
Provided.
P
Rated frequency or frequency
range
range
DC.
N
Rated current
1 A
P
Manufacturers name, trade mark or
identification mark
identification mark
—
Type / model
on stage
P
Symbol of Class II
Class III equipment.
N
Other symbols
The additional marking does not give rise to
misunderstandings.
misunderstandings.
P
Certification marks
Refer to label.
—
1.7.2
Safety instructions
Provided with marking regarding use of specified power
supply, refer to marking label.
supply, refer to marking label.
P
Operating instructions
Installation instructions are available to the user in
User’s Manual.
User’s Manual.
P
1.7.3
Short duty cycles
The equipment is intended for continuous operation.
N
1.7.4
Supply voltage adjustment
No voltage selector.
N
1.7.5
Power outlets on the equipment
No standard power outlet.
N
1.7.6
Fuse identification
No fusing.
N
1.7.7
Wiring terminals
Class III equipment.
N
Click on the first or last page to see other ON STAGE (serv.man3) service manuals if exist.