JBL ON STAGE (serv.man3) EMC - CB Certificate ▷ View online
IEC 60950 3rd. Ed, 1999
- Page 3 of 5 -
Order No. 23171
4.3.12
The maximum quantity of flammable liquid
stored in equipment is required to comply with
NFPA 30.
stored in equipment is required to comply with
NFPA 30.
No flammable liquids within the
equipment.
equipment.
N
4.3.13
Equipment with lasers is required to meet
Code of Federal Regulations 21CFR 1040 and
Canadian Radiation Emitting Devices Act,
REDR C1370.
Code of Federal Regulations 21CFR 1040 and
Canadian Radiation Emitting Devices Act,
REDR C1370.
LEDs are defused type.
N
4.7.1
For computer room applications, automated
information storage systems with combustible
media greater than 27 cubic feet are required
to have a provision for connection of either
automatic sprinklers or a gaseous agent
extinguishing system with an extended
discharge.
information storage systems with combustible
media greater than 27 cubic feet are required
to have a provision for connection of either
automatic sprinklers or a gaseous agent
extinguishing system with an extended
discharge.
The equipment has no combustible
area greater than 27 cubic feet.
area greater than 27 cubic feet.
N
4.7.3.1
For computer room applications, enclosures
with combustible material measuring greater
than 0.9 m
with combustible material measuring greater
than 0.9 m
2
or a single dimension greater than
1.8 m, are required to have a flame spread
rating of 50 or less. For other applications,
enclosures with the same dimensions require a
flame spread rating of 200 or less.
rating of 50 or less. For other applications,
enclosures with the same dimensions require a
flame spread rating of 200 or less.
The equipment has no combustible
material greater than 0.93m2 or
single dimension greater than 1.8m.
material greater than 0.93m2 or
single dimension greater than 1.8m.
N
Annex H
Equipment that produces ionizing radiation is
required to comply with Code of Federal
Regulations, 21 CFR 1020 and Canadian
Radiation Emitting Devices Act, REDR C1370.
required to comply with Code of Federal
Regulations, 21 CFR 1020 and Canadian
Radiation Emitting Devices Act, REDR C1370.
The equipment does not produce
ionizing radiation.
ionizing radiation.
N
IEC 60950 3rd. Ed, 1999
- Page 4 of 5 -
Order No. 23171
The following key national differences are based on re quirements other than
national regulatory requirements. The bi-national standard referenced above
should be consulted for further details on the national differences summarized
below.
national regulatory requirements. The bi-national standard referenced above
should be consulted for further details on the national differences summarized
below.
—
1.5.1
Some components and materials associated
with the risk of fire, electric shock, or personal
injury are required to have component or
material ratings in accordance with the
applicable national (U.S. and Canadian)
component or material requirements.
These components include:
attachment plugs, cathode ray tubes, circuit
breakers, communication circuit accessories,
cord sets and power supply cords, direct plug-
in equipment, enclosures (outdoor), flexible
cords and cables, fuses (branch circuit),
fuseholders, ground-fault current interrupters,
industrial control equipment, insulating tape,
interconnecting cables, lampholders, limit
controls, printed wiring, protectors for
communications circuits, receptacles, solid
state controls, supplementary protectors, surge
suppressors, switches (including interlock
switches), thermal cutoffs, thermostats,
transformer winding wire, tubing, wire
connectors and wire and cables
with the risk of fire, electric shock, or personal
injury are required to have component or
material ratings in accordance with the
applicable national (U.S. and Canadian)
component or material requirements.
These components include:
attachment plugs, cathode ray tubes, circuit
breakers, communication circuit accessories,
cord sets and power supply cords, direct plug-
in equipment, enclosures (outdoor), flexible
cords and cables, fuses (branch circuit),
fuseholders, ground-fault current interrupters,
industrial control equipment, insulating tape,
interconnecting cables, lampholders, limit
controls, printed wiring, protectors for
communications circuits, receptacles, solid
state controls, supplementary protectors, surge
suppressors, switches (including interlock
switches), thermal cutoffs, thermostats,
transformer winding wire, tubing, wire
connectors and wire and cables
All critical components are IEC, UL
or CSA certified. See list of critical
components in main CB report
(§1.5.01).
or CSA certified. See list of critical
components in main CB report
(§1.5.01).
P
2.3.1
For TNV-2 and TNV-3 circuits with other than
ringing signals and with voltages exceeding
42.4 Vp or 60 Vdc, the maximum acceptable
current through a 2000 ohm resistor (or
greater) connected across the voltage source
with other loads disconnected is 7.1 mA peak
or 30 mA dc under normal operating
conditions.
ringing signals and with voltages exceeding
42.4 Vp or 60 Vdc, the maximum acceptable
current through a 2000 ohm resistor (or
greater) connected across the voltage source
with other loads disconnected is 7.1 mA peak
or 30 mA dc under normal operating
conditions.
No TNV circuitry.
N
2.6.3.3
When subject to impedance testing, protective
earthing and bonding is required to be tested
subject per the specified test conditions that
originate in CSA C22.2 No. 0.4.
earthing and bonding is required to be tested
subject per the specified test conditions that
originate in CSA C22.2 No. 0.4.
Class III equipment.
N
4.2.8.1
Enclosures around CRT’s with a face area of
160 mm or more are required to reduce the
risk of injury due to the implosion of the CRT.
160 mm or more are required to reduce the
risk of injury due to the implosion of the CRT.
No CRTs in the equipment.
N
IEC 60950 3rd. Ed, 1999
- Page 5 of 5 -
Order No. 23171
4.3.2
Equipment with handles is required to comply
with special loading tests.
with special loading tests.
The equipment is not provided with
handles.
handles.
N
5.1.8.1.1
Equipment intended to receive
telecommunication ringing signals is required
to comply with a special touch current
measurement tests.
telecommunication ringing signals is required
to comply with a special touch current
measurement tests.
No TNV circuitry.
N
6.2.1
Enamel coating on winding wire not
considered electrical separation unless
subjected to special investigation.
considered electrical separation unless
subjected to special investigation.
No TNV circuitry.
N
6.4
Equipment intended for connection to
telecommunication network outside plant cable
is required to be protected against overvoltage
from power line crosses in accordance with 6 .4
and Annex NAC.
telecommunication network outside plant cable
is required to be protected against overvoltage
from power line crosses in accordance with 6 .4
and Annex NAC.
No TNV circuitry.
N
6.5
Equipment connected to a telecommunications
network and supplied with an earphone
intended to be held against, or in the ear is
required to comply with special acoustic
pressure tests.
network and supplied with an earphone
intended to be held against, or in the ear is
required to comply with special acoustic
pressure tests.
No TNV circuitry.
N
M.2
Continuous ringing signals up to 16mA only
are permitted if the equipment is subject to
special installation and performance
restrictions.
are permitted if the equipment is subject to
special installation and performance
restrictions.
No TNV circuitry.
N
Annex NAB Equipment connected to centralized d.c. power
systems is required to comply with special
earthing, wiring, marking and insulation
requirements in accordance with Annex NAB
and 3.6.1.
earthing, wiring, marking and insulation
requirements in accordance with Annex NAB
and 3.6.1.
The equipment is not connected to
a centralized d.c. power system.
a centralized d.c. power system.
N
IEC 60950 3rd. Ed, 1999
- Page 5 of 5 -
Order No. 23171
4.3.2
Equipment with handles is required to comply
with special loading tests.
with special loading tests.
The equipment is not provided with
handles.
handles.
N
5.1.8.1.1
Equipment intended to receive
telecommunication ringing signals is required
to comply with a special touch current
measurement tests.
telecommunication ringing signals is required
to comply with a special touch current
measurement tests.
No TNV circuitry.
N
6.2.1
Enamel coating on winding wire not
considered electrical separation unless
subjected to special investigation.
considered electrical separation unless
subjected to special investigation.
No TNV circuitry.
N
6.4
Equipment intended for connection to
telecommunication network outside plant cable
is required to be protected against overvoltage
from power line crosses in accordance with 6 .4
and Annex NAC.
telecommunication network outside plant cable
is required to be protected against overvoltage
from power line crosses in accordance with 6 .4
and Annex NAC.
No TNV circuitry.
N
6.5
Equipment connected to a telecommunications
network and supplied with an earphone
intended to be held against, or in the ear is
required to comply with special acoustic
pressure tests.
network and supplied with an earphone
intended to be held against, or in the ear is
required to comply with special acoustic
pressure tests.
No TNV circuitry.
N
M.2
Continuous ringing signals up to 16mA only
are permitted if the equipment is subject to
special installation and performance
restrictions.
are permitted if the equipment is subject to
special installation and performance
restrictions.
No TNV circuitry.
N
Annex NAB Equipment connected to centralized d.c. power
systems is required to comply with special
earthing, wiring, marking and insulation
requirements in accordance with Annex NAB
and 3.6.1.
earthing, wiring, marking and insulation
requirements in accordance with Annex NAB
and 3.6.1.
The equipment is not connected to
a centralized d.c. power system.
a centralized d.c. power system.
N