JBL ON BEAT RUMBLE EMC - CB Certificate ▷ View online
Issue Date:
2013-01-09
Page 27 of 41
Report Reference #
E204594-A39-CB-1
IEC 60950-1:2005
SubClause Difference + Test
Result - Remark
Verdict
This report issued under the responsibility of UL
1.5.5
For other than limited power and TNV
circuits, the type of output circuit identified for
output connector.
N/A
1.5.5
External cable assemblies that exceed 3.05
m in length to be types specified in the NEC and
CEC.
N/A
1.5.5
Detachable external interconnecting cables
3.05 m or less in length and provided with
equipment marked to identify the responsible
organization and the designation for the cable.
N/A
1.5.5
Building wiring and cable for use in ducts,
plenums and other air handling space subject to
special requirements and excluded from scope.
N/A
1.5.5
Telephone line and extension cords and the
like comply with UL 1863 and CSA C22.2 No. 233.
N/A
1.6.1.2
Equipment intended for connection to a d.c.
power (mains) distribution system is subject to
special circuit classification requirements (e.g.,
TNV-2)
N/A
1.6.1.2
Earthing of d.c. powered equipment
provided.
N/A
1.7
Lamp replacement information indicated on
lampholder in operator access area.
N/A
1.7.1
Special marking format for equipment
intended for use on a supply system with an
earthed neutral and more than one phase
N/A
Issue Date:
2013-01-09
Page 28 of 41
Report Reference #
E204594-A39-CB-1
IEC 60950-1:2005
SubClause Difference + Test
Result - Remark
Verdict
This report issued under the responsibility of UL
conductor.
1.7.1
Equipment voltage rating not higher than
rating of the plug except under special conditions.
N/A
1.7.6
Special fuse replacement marking for
operator accessible fuses.
N/A
1.7.7
Identification of terminal connection of the
equipment earthing conductor.
N/A
1.7.7
Connectors and field wiring terminals for
external Class 2 or Class 3 circuits provided with
marking indicating minimum Class of wiring to be
used.
N/A
1.7.7
Marking located adjacent to terminals and
visible during wiring.
N/A
2.1.1.1
Bare TNV conductive parts in the interior of
equipment normally protected against contact by a
cover intended for occasional removal are exempt
provided instructions include directions for
disconnection of TNV prior to removal of the cover.
N/A
2.3.1.b
Other telecommunication signaling systems
(e.g., message waiting) than described in 2.3.1(b)
are subject to M.4.
N/A
2.3.1.b
For TNV-2 and TNV-3 circuits with other
than ringing signals and with voltages exceeding
42.4 Vp or 60 V d.c., the maximum current limit
through a 2000 Ohm or greater resistor with loads
disconnected is 7.1 mA peak or 30 mA d.c. under
normal conditions.
N/A
Issue Date:
2013-01-09
Page 29 of 41
Report Reference #
E204594-A39-CB-1
IEC 60950-1:2005
SubClause Difference + Test
Result - Remark
Verdict
This report issued under the responsibility of UL
2.3.1.b
Limits for measurements across 5000 ohm
resistor in the event of a single fault are replaced
after 200 ms with the limits of M.3.1.4.
N/A
2.3.2.1
In the event of a single fault, the limits of
2.2.3 apply to SELV circuits and accessible
conductive parts.
N/A
2.3.2.4
Enamel coating on signal transformer
winding wire allowed as an alternative to Basic
insulation in specific telecommunication
applications when subjected to special construction
requirements and routine testing.
N/A
2.5
Overcurrent protection device required for
Class 2 and Class 3 limiting in accordance with the
NEC, or for a Limited Power Source, not
interchangeable with devices of higher ratings if
operator replaceable.
N/A
2.6
Equipment having receptacles for output
a.c. power connectors generated from an internal
separately derived source have the earthed
(grounded) circuit conductor suitably bonded to
earth.
N/A
2.6.3.3
For PLUGGABLE EQUIPMENT TYPE A, if
a) b) or c) are not applicable, the current rating of
the circuit is taken as 20 A
N/A
2.6.3.3
The first column on Table 2D requirement:
“Smaller of the RATED CURRENT of the
equipment or the PROTECTIVE CURRENT
RATING of the circuit under consideration."
N/A
2.6.3.4
Capacity of connection between earthing
terminal and parts required to be earthed subject to
N/A
Issue Date:
2013-01-09
Page 30 of 41
Report Reference #
E204594-A39-CB-1
IEC 60950-1:2005
SubClause Difference + Test
Result - Remark
Verdict
This report issued under the responsibility of UL
special conditions based on the current rating of
the circuit.
the circuit.
2.6.3.4
Protective bonding conductors and their
terminals of non-standard constructions (e.g. PWB
traces) evaluated to limited short-circuit test of CSA
C22.2 No.0.4.
N/A
2.6.4.1
Field wiring terminals for earthing
conductors suitable for wire sizes (gauge) used in
US and Canada.
N/A
2.7.1
Data for selection of special external branch
circuit overcurrent devices marked on the
equipment.
N/A
2.7.1
Standard supply outlets protected by
overcurrent device in accordance with the NEC,
and CEC, Part 1.
N/A
2.7.1
Overcurrent protection for individual
transformers that distribute power to other units
over branch circuit wiring.
N/A
2.7.1
Additional requirements for overcurrent
protection apply to equipment provided with
panelboards.
N/A
2.7.1
Non-motor-operated equipment requiring
special overcurrent protective device marked with
device rating.
N/A
2.10.5.12
Multi-layer winding wire subject to UL
component wire requirements in addition to
2.10.5.12 and Annex U.
N/A
Click on the first or last page to see other ON BEAT RUMBLE service manuals if exist.