JBL ON BEAT MICRO (serv.man3) EMC - CB Certificate ▷ View online
Issue Date:
2012-10-23
Page 9 of 50
Report Reference #
E204594-A37-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
1
GENERAL
Pass
1.5
Components
Pass
1.5.1
General
Pass
Comply with IEC 60950-1 or relevant component
standard
standard
(See appended table 1.5.1)
Pass
1.5.2
Evaluation and testing of components
Components certified to IEC
harmonized standard and
checked for correct
application.
Components not certified are
used in accordance with their
ratings and they comply with
applicable parts of IEC 60950-
1 and the relevant component
Standard.
Components, for which no
relevant IEC-Standard exist,
have been tested under the
conditions occurring in the
equipment, using applicable
parts of IEC 60950-1.
harmonized standard and
checked for correct
application.
Components not certified are
used in accordance with their
ratings and they comply with
applicable parts of IEC 60950-
1 and the relevant component
Standard.
Components, for which no
relevant IEC-Standard exist,
have been tested under the
conditions occurring in the
equipment, using applicable
parts of IEC 60950-1.
Pass
1.5.3
Thermal controls
N/A
1.5.4
Transformers
N/A
1.5.5
Interconnecting cables
Not provided.
N/A
1.5.6
Capacitors bridging insulation
N/A
1.5.7
Resistors bridging insulation
N/A
1.5.7.1
Resistors bridging functional, basic or
supplementary insulation
supplementary insulation
N/A
1.5.7.2
Resistors bridging double or reinforced insulation
between a.c. mains and other circuits
between a.c. mains and other circuits
N/A
1.5.7.3
Resistors bridging double or reinforced insulation
between a.c. mains and antenna or coaxial cable
between a.c. mains and antenna or coaxial cable
N/A
1.5.8
Components in equipment for IT power systems
N/A
1.5.9
Surge suppressors
No surge suppressor used.
N/A
1.5.9.1
General
N/A
1.5.9.2
Protection of VDRs
N/A
1.5.9.3
Bridging of functional insulation by a VDR
N/A
1.5.9.4
Bridging of basic insulation by a VDR
N/A
Issue Date:
2012-10-23
Page 10 of 50
Report Reference #
E204594-A37-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
1.5.9.5
Bridging of supplementary, double or reinforced
insulation by a VDR
insulation by a VDR
N/A
1.6
Power interface
Pass
1.6.1
AC power distribution systems
Class III equipment intended to
be supplied by an external
SELV power supply marked
LPS.
be supplied by an external
SELV power supply marked
LPS.
Pass
1.6.2
Input current
For reference only. The steady
state input current of the
equipment did not exceed the
RATED CURRENT by more
than 10% under NORMAL
LOAD.
See appended Table 1.6.2.
state input current of the
equipment did not exceed the
RATED CURRENT by more
than 10% under NORMAL
LOAD.
See appended Table 1.6.2.
Pass
1.6.3
Voltage limit of hand-held equipment
N/A
1.6.4
Neutral conductor
N/A
Issue Date:
2012-10-23
Page 11 of 50
Report Reference #
E204594-A37-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
1.7
Marking and instructions
Pass
1.7.1
Power rating and identification markings
Pass
1.7.1.1
Power rating mark
Pass
Multiple mains supply connections ........................ :
N/A
Rated voltage(s) or voltage range(s) (V) ............... :
Class III. Not required. See
Models and Ratings.
Models and Ratings.
N/A
Symbol for nature of supply, for d.c. only .............. :
N/A
Rated frequency or rated frequency range (Hz) .... :
N/A
Rated current (mA or A) ........................................ :
Class III. Not required. See
Models and Ratings.
Models and Ratings.
N/A
1.7.1.2
Identification markings
Pass
Manufacturer's name or trademark or identification
mark ....................................................................... :
mark ....................................................................... :
1. See CB Certificate 2. See
Marking label 3. Trademark
authorized.
Marking label 3. Trademark
authorized.
Pass
Model identification or type reference ................... :
Refer to the Model information
at the beginning of this Test
Report.
at the beginning of this Test
Report.
Pass
Symbol for Class II equipment only ....................... :
Class III equipment
N/A
Other markings and symbols ................................. :
N/A
1.7.2
Safety instructions and marking
Operating/safety instructions
made available to the user.
made available to the user.
Pass
1.7.2.1
General
Pass
1.7.2.2
Disconnect devices
N/A
1.7.2.3
Overcurrent protective device
N/A
1.7.2.4
IT Power distribution systems
N/A
1.7.2.5
Operator access with a tool
N/A
1.7.2.6
Ozone
N/A
1.7.3
Short duty cycles
N/A
1.7.4
Supply voltage adjustment .................................... :
N/A
Method and means of adjustment; reference to
installation instructions .......................................... :
installation instructions .......................................... :
N/A
1.7.5
Power outlets on the equipment ............................ :
N/A
1.7.6
Fuse identification (marking, special fusing
characteristics, cross-reference) ........................... :
characteristics, cross-reference) ........................... :
N/A
1.7.7
Wiring terminals
Class III equipment
N/A
1.7.7.1
Protective earthing and bonding terminals ............ :
N/A
Issue Date:
2012-10-23
Page 12 of 50
Report Reference #
E204594-A37-CB-1
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. : IEC60950_1B
This report issued under the responsibility of UL
1.7.7.2
Terminals for a.c. mains supply conductors
N/A
1.7.7.3
Terminals for d.c. mains supply conductors
N/A
1.7.8
Controls and indicators
N/A
1.7.8.1
Identification, location and marking ....................... :
N/A
1.7.8.2
Colours .................................................................. :
N/A
1.7.8.3
Symbols according to IEC 60417 .......................... :
N/A
1.7.8.4
Markings using figures ........................................... :
N/A
1.7.9
Isolation of multiple power sources ....................... :
N/A
1.7.10
Thermostats and other regulating devices ............ :
N/A
1.7.11
Durability
All markings provided on UL
Recognized Component labels
suitable for surface they are
applied upon or meet the
durability test.
Recognized Component labels
suitable for surface they are
applied upon or meet the
durability test.
Pass
1.7.12
Removable parts
No removable parts.
N/A
1.7.13
Replaceable batteries ............................................ :
A statement in the operating
instruction.
instruction.
Pass
Language(s) .......................................................... :
Reviewed only English
markings/instructions.
May be provided in other
languages upon request from
the manufacturer.
markings/instructions.
May be provided in other
languages upon request from
the manufacturer.
-
1.7.14
Equipment for restricted access locations ............. :
N/A
Click on the first or last page to see other ON BEAT MICRO (serv.man3) service manuals if exist.