JBL CONTROL 2.4G (serv.man9) EMC - CB Certificate ▷ View online
Registration number: «Registriernummer»-E-16
ETS PRODUCT SERVICE AG
STORKOWER STRASSE 38C-15526 REICHENWALDE B. BERLIN Page 20 of 50
Line conducted Emission
Test Equipment
a) Absorbing clamp (MDS 21)
For your reference please find it in our test equipment list at page 9 to 17 as number : 39.
b) Controller (HD 050)
For your reference please find it in our test equipment list at page 9 to 17 as number : 32.
c) Monitoring System
For your reference please find it in our test equipment list at page 9 to 17 as number : 71.
d) Shielded Room
For your reference please find it in our test equipment list at page 9 to 17 as number : 85.
e) EMI test receiver ESCS-30
For your reference please find it in our test equipment list at page 9 to 17 as number : 474.
f) Software
ES-K1 Rohde & Schwarz, Vers. 1.6SP2
Test Procedures
• Test configuration
The test configuration corresponds to the standard EN 55013 /1/. The equipment under test is placed on
a non-metallic table with 0,8m high.
The lead to be measured is stretched horizontally in a straight line, to permit variation in position of the
absorbing clamp along the lead to find the maximum indication. The lead shall be at least length of 6
meter. The absorbing clamp is placed around the lead (see picture 3). The observation of the equipment
under test is realized by a video camera and by a microphone.
• Test parameters and marginal conditions
The test is carried out with a frequency range between 30 MHz to 300 MHz. Further information please
find in test report.
Registration number: «Registriernummer»-E-16
ETS PRODUCT SERVICE AG
STORKOWER STRASSE 38C-15526 REICHENWALDE B. BERLIN Page 21 of 50
Picture 3
0,
8-1,
0m
Ma
in
s
Emission with absorbing clamp
according to
EN 55013
Registration number: «Registriernummer»-E-16
ETS PRODUCT SERVICE AG
STORKOWER STRASSE 38C-15526 REICHENWALDE B. BERLIN Page 22 of 50
Radiated Emission (EN 55013)
Test Equipment
a) Antenna (HK116)
For your reference please find it in our test equipment list at page 9 to 17 as number : 12.
b) Antenna (HL223)
For your reference please find it in our test equipment list at page 9 to 17 as number : 13.
c) Video camera system
For your reference please find it in our test equipment list at page 9 to 17 as number : 71.
d) Interphone system
For your reference please find it in our test equipment list at page 9 to 17 as number : 72.
e) Semi anechoic chamber
For your reference please find it in our test equipment list at page 9 to 17 as number : 178.
f) EMI test receiver ESCS-30
For your reference please find it in our test equipment list at page 9 to 17 as number : 474.
g) Software
ES-K1 Rohde & Schwarz, Vers. 1.6 SP2
Test Procedures
• Test configuration
The test configuration corresponds to standard EN 55013 /1/. The equipment under test is placed on
a non-metallic table, 0,8m high. The power supply and the RF connection points are close to the
equipment under test on the floor inside a connection box. The cables to this connection box are
shielded and below the double floor (see picture 4). The receiving antenna is placed in a height of
1,0 to 4,0m, in a distance of 3m. The measurement receiver is placed in a special room. The
observation of the equipment under test is realized by video camera and by a microphone.
• Test parameters and marginal conditions
The test is carried out with horizontal and vertical polarization of the antenna in a frequency range
of 30 MHz to 1000 MHz. For further information please see the test protocol.
Registration number: «Registriernummer»-E-16
ETS PRODUCT SERVICE AG
STORKOWER STRASSE 38C-15526 REICHENWALDE B. BERLIN Page 23 of 50
Radiated Emission according to
EN 55013
+
Meas.
Equipment
Filter
Mains
EUT
Filter
Mains
Generator
3m
h
=
1
m
-
4
m
0
.8
m
Dipol
+
rotating coaxial connector (if necessary)
Picture 4
Click on the first or last page to see other CONTROL 2.4G (serv.man9) service manuals if exist.