JBL CINEMA 610 EMC - CB Certificate ▷ View online
Page 56 of 99
Report No.: 17032770 001
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
J.2
NO: After Table J.1 the following is added:
In Norway, due to the IT power distribution system
used, the a.c. MAINS supply voltage is considered
to be equal to the line-to-line voltage, and will
remain 230 V in case of a single earth fault.
used, the a.c. MAINS supply voltage is considered
to be equal to the line-to-line voltage, and will
remain 230 V in case of a single earth fault.
Justification: Based on a use in Norway of an IT
power distribution system where the neutral is not
provided.
power distribution system where the neutral is not
provided.
N/A
ZC
ANNEX ZC TO EN 60065, A-DEVIATIONS (EN)
5.1
IT: Additional markings on the outside of the TV
receiver in Italian language
receiver in Italian language
No TV used.
N/A
IT:User instructions in Italian language including a
conformity declaration
conformity declaration
N/A
IT: Certification number on the back cover
N/A
6.1
DE: The following requirement applies:
For the operation of any cathode ray tube intended
for the display of visual images operating at an
acceleration voltage exceeding 40 kV, authorization
is required, or application of type approval
(Bauartzulassung) and marking.
for the display of visual images operating at an
acceleration voltage exceeding 40 kV, authorization
is required, or application of type approval
(Bauartzulassung) and marking.
Justification: German ministerial decree against
ionizing radiation (Röntgenverordnung), in force
since 2002-07-01, implementing the European
Directive 96/29/EURATOM.
ionizing radiation (Röntgenverordnung), in force
since 2002-07-01, implementing the European
Directive 96/29/EURATOM.
NOTE Contact address:
N/A
14
SE: Switches containing mercury such as
thermostats, relays and level controllers are not
allowed.
thermostats, relays and level controllers are not
allowed.
Justification: Ordinance (1990:944) on Prohibition
in Connection with handling. Importation and
exportation of Chemical Products (Certain Cases)
in Connection with handling. Importation and
exportation of Chemical Products (Certain Cases)
No such switch used.
P
Page 57 of 99
Report No.: 17032770 001
National Deviations
Clause
Requirement
– Test
Result - Remark
Verdict
Australia National Differences acc. to IEC 60065:2001 + A1 + A2
APPENDIX Australia National Differences according to CB Bulletin
(IEC Publication 60065 7th edition, 2001+ A1:2006+A2:2010)
--
EXPLANATION FOR ABBREVIATIONS
P=Pass, F=Fail, N/A=Not applicable. Placed in the column to the right.
ZZ.1
Introduction
This Annex sets out variations between this Standard
and IEC 60065:2001. These variations indicate
national variations for purposes of the IECEE CB
Scheme and will be published in the IECEE CB
Bulletin. These variations are indicated within the
body of the Standard by shading and strikethrough.
and IEC 60065:2001. These variations indicate
national variations for purposes of the IECEE CB
Scheme and will be published in the IECEE CB
Bulletin. These variations are indicated within the
body of the Standard by shading and strikethrough.
P
ZZ.2
Variations
The variations are as follows:
P
7.1.5
In table 3, under item c) add an
h)
in both columns
against “thermoplastic materials’ and add the
following new footnote:
following new footnote:
hAs an alternative to the method described in
footnote f) the following variation may be used
where there is any doubt about the suitability of
the material:
where there is any doubt about the suitability of
the material:
The ball-pressure test described in AS/NZS
60695.10.2 may be carried out.
60695.10.2 may be carried out.
To assess compliance under normal operating
conditions the test is made in a heating cabinet at
a temperature of 40
conditions the test is made in a heating cabinet at
a temperature of 40
C
2
C plus the maximum
temperature rise determined under normal
operating conditions but, it shall be at least
operating conditions but, it shall be at least
-
for external parts.......................75
C
2
C
-
for materials supporting parts
CONDUCTIVELY CONNECTED
TO THE MAINS.............................125
C
2
C
Alternative method not
applied.
applied.
N/A
7.2
After the second paragraph, add the following:
The alternative method described in footnote h) of
Table 3 may be used.
Table 3 may be used.
Alternative method not
applied.
applied.
N/A
15.1.1
After the second paragraph, add the following:
Plugs for the connection of apparatus to mains-
powered socket-outlets shall comply with AS/NZS
3112 or AS/NZS 3123. Apparatus with a plug portion,
suitable for insertion into a 10A 3 pin flat-pin flat-pin
socket-outlet complying with AS/NZS 3112, shall
comply with the requirements of AS/NZS 3112 for
equipment with integral pins for insertion into socket-
outlets.
Plugs for the connection of apparatus to mains-
powered socket-outlets shall comply with AS/NZS
3112 or AS/NZS 3123. Apparatus with a plug portion,
suitable for insertion into a 10A 3 pin flat-pin flat-pin
socket-outlet complying with AS/NZS 3112, shall
comply with the requirements of AS/NZS 3112 for
equipment with integral pins for insertion into socket-
outlets.
No such plugs provided.
N/A
15.3.5
In Table 15, in the second and third rows of the first
column replace “6” with “7.5”.
column replace “6” with “7.5”.
Replaced.
N/A
Page 58 of 99
Report No.: 17032770 001
National Deviations
Clause
Requirement
– Test
Result - Remark
Verdict
Australia National Differences acc. to IEC 60065:2001 + A1 + A2
16.2
In Table 18, in the second and third rows of the first
column replace “6” with “7.5”.
column replace “6” with “7.5”.
N/A
16.3
After item (b) add the following:
A flexible cord complying with AS/NZS 3191 need not
undergo this test.
undergo this test.
Not provided.
N/A
19.201
Add the following after Clause 19.6:
19.201 Additional stability requirements for
television receivers
television receivers
Television receivers and display devices that may be
used for television purposes, with a mass of 7kg or
more, shall have additional stability requirements.
used for television purposes, with a mass of 7kg or
more, shall have additional stability requirements.
Compliance is checked by inspection and by the
tests of 19.201.2.2 and 19.201.3 as applicable.
tests of 19.201.2.2 and 19.201.3 as applicable.
Apparatus designed for only fixing to a wall, ceiling
or equipment rack are not required to be subjected
to these additional requirements if the marking of
5.4.1 f) is provided on or with the apparatus.
or equipment rack are not required to be subjected
to these additional requirements if the marking of
5.4.1 f) is provided on or with the apparatus.
N/A
19.201.1 Warning notice
Television receivers and display devices that may be used for television purposes,
shall be provided with information in the instructions for installation for use,
containing the following information or similar:
shall be provided with information in the instructions for installation for use,
containing the following information or similar:
IMPORTANT INFORMATION
If a television is not positioned in a sufficiently stable location, it can be potentially
hazardous due to falling. Many injuries, particularly to children, can be avoided by taking
simple precautions such as:
hazardous due to falling. Many injuries, particularly to children, can be avoided by taking
simple precautions such as:
Using cabinets or stands recommended by the manufacturer of the t elevision.
Only using furniture that can safely support the television.
Ensuring the television is not overhanging the edge of the supporting furniture.
Not placing the television on tall furniture (for example, cupboards or bookcases)
without anchoring both the furniture and the television to a suitable support.
Not standing the televisions on cloth or other materials placed between the
television
television
and supporting furniture.
Educating children about the dangers of climbing on furniture to reach the
television
television
or its controls.
Such information should also be provided as a label on the apparatus.
NOTE: The committee is considering a request from Regulatory Authorities that
providing the information as a label on the apparatus should be mandatory.
providing the information as a label on the apparatus should be mandatory.
19.201.2 Restraining device
19.201.2.1 Television receivers should be provided with a restraining device such
as a fixing point to facilitate restraining the television from toppling forward.
as a fixing point to facilitate restraining the television from toppling forward.
NOTE: The committee is considering a request from Regulatory Authorities that
providing a restraining device on the apparatus should be mandatory.
providing a restraining device on the apparatus should be mandatory.
N/A
Page 59 of 99
Report No.: 17032770 001
National Deviations
Clause
Requirement
– Test
Result - Remark
Verdict
Australia National Differences acc. to IEC 60065:2001 + A1 + A2
20
Add the following after NOTE 2:
For alternative test refer to Clause 20.201.
Alternative tests not applied
for.
for.
P
20.1.4
In Table 21, in the third and fourth columns change
both “HB75” and “No requirement” to “V-1”.
both “HB75” and “No requirement” to “V-1”.
Changed.
P
20.2.3
After this Clause, add the following variation:
20.201 Resistance to fire - Alternative tests
20.201.1 General
Parts of non-metallic material shall be resistant to
ignition and the spread of fire.
ignition and the spread of fire.
This requirement does not apply to decorative trims,
knobs and other parts unlikely to be ignited or to
propagate flames originating from inside the
apparatus, or the following:
knobs and other parts unlikely to be ignited or to
propagate flames originating from inside the
apparatus, or the following:
(a) Components that are contained in an
enclosure having a flammability category of
V-0 according to AS/NZS 60695.11.10 and
having openings only for the connecting wires
filling the openings completely, and for
ventilation not exceeding 1 mm in width
regardless of length.
V-0 according to AS/NZS 60695.11.10 and
having openings only for the connecting wires
filling the openings completely, and for
ventilation not exceeding 1 mm in width
regardless of length.
(b) The following parts which would contribute
negligible fuel to a fire:
- small mechanical parts, the mass of
which does not exceed 4g, such as
mounting parts, gears, cams, belts and
bearings;
mounting parts, gears, cams, belts and
bearings;
- small electrical components, such as
capacitors with a volume not exceeding
1750mm
1750mm
3
, integrated circuits, transistors
and optocoupler packages, if these
components are mounted on material of
flammability category V-1 or better
according to AS/NZS 60695.11.10
components are mounted on material of
flammability category V-1 or better
according to AS/NZS 60695.11.10
Added, alternative tests not
applied.
applied.
N/A
Click on the first or last page to see other CINEMA 610 service manuals if exist.