JBL CINEMA 610 EMC - CB Certificate ▷ View online
Page 48 of 99
Report No.: 17032770 001
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
Zx.5 Measurement methods
Measurements shall be made in accordance with
EN 50332-1 or EN 50332-2 as applicable.
Unless stated otherwise, the time interval T shall be
30 s.
NOTE Test method for wireless equipment
provided without listening device should be defined.
Measurements shall be made in accordance with
EN 50332-1 or EN 50332-2 as applicable.
Unless stated otherwise, the time interval T shall be
30 s.
NOTE Test method for wireless equipment
provided without listening device should be defined.
N/A
Page 49 of 99
Report No.: 17032770 001
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
6.1
(A11:2008)
Replace the entire subclause in EN 60065:2002
and EN 60065:2002/A1:2006 by:
and EN 60065:2002/A1:2006 by:
Ionizing radiation
Apparatus including a potential source of ionizing
radiation shall be so constructed that personal
radiation shall be so constructed that personal
protection against ionizing radiation is provided
under normal operating conditions and under fault
under normal operating conditions and under fault
conditions.
Compliance is checked by measurement under the
following conditions:
following conditions:
In addition to the normal operating conditions, all
controls adjustable from the outside BY HAND, by
any object such as a tool or a coin, and those
internal adjustments or pre-sets which are not
locked in a reliable manner, are adjusted so as to
give maximum radiation whilst maintaining an
intelligible picture for 1 h, at the end of which the
measurement is made.
controls adjustable from the outside BY HAND, by
any object such as a tool or a coin, and those
internal adjustments or pre-sets which are not
locked in a reliable manner, are adjusted so as to
give maximum radiation whilst maintaining an
intelligible picture for 1 h, at the end of which the
measurement is made.
NOTE 1 Soldered joints and paint lockings are
examples of adequate locking.
examples of adequate locking.
The dose-rate is determined by means of a
radiation monitor with an effective area of 10 cm²,
at any point 10 cm from the outer surface of the
apparatus.
radiation monitor with an effective area of 10 cm²,
at any point 10 cm from the outer surface of the
apparatus.
Moreover, the measurement shall be made under
fault conditions causing an increase of the high-
voltage, provided an intelligible picture is
maintained for 1 h, at the end of which the
measurement is made.
fault conditions causing an increase of the high-
voltage, provided an intelligible picture is
maintained for 1 h, at the end of which the
measurement is made.
The dose-
rate shall not exceed 1μSv/h (0,1 mR/h)
taking account of the background level.
NOTE 2 These values appear in Directive
96/29/Euratom of 13th May 1996.
96/29/Euratom of 13th May 1996.
A picture is considered to be intelligible if the
following conditions are met:
following conditions are met:
- a scanning amplitude of at least 70 % of the
usable screen width;
- a minimum luminance of 50 cd/m² with locked
blank raster provided by a test generator;
- a horizontal resolution corresponding to at least
1,5 MHz in the centre, with a similar vertical
degradation;
degradation;
- not more than one flashover per 5 min.
No such radiation.
N/A
Page 50 of 99
Report No.: 17032770 001
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
Z1
(A11:2008)
Add the following new clause after Clause 20:
Z1 Resistance to candle flame ignition
A television set shall be so designed that the
likelihood of ignition and the spread of fire caused
by a candle flame is reduced.
likelihood of ignition and the spread of fire caused
by a candle flame is reduced.
NOTE 1 An apparatus with a viewing screen is not
regarded to be a television set if it is declared not to
be so by the manufacturer.
regarded to be a television set if it is declared not to
be so by the manufacturer.
This requirement does not apply to the display
screen of rear projection TV’s.
NOTE 2 This exemption has been allowed because
this technology is falling out of use and it is
expected that within a few years it will no longer
exist. This exemption will not be extended to other
technologies.
screen of rear projection TV’s.
NOTE 2 This exemption has been allowed because
this technology is falling out of use and it is
expected that within a few years it will no longer
exist. This exemption will not be extended to other
technologies.
NOTE 3 The frame around the screen is not
exempted from the requirements.
exempted from the requirements.
Wood and WOOD-BASED MATERIAL with a
thickness of at least 6 mm is considered to fulfil the
V-1 requirement when applying CLC/TS 62441.
thickness of at least 6 mm is considered to fulfil the
V-1 requirement when applying CLC/TS 62441.
Compliance is checked according to CLC/TS
62441.
62441.
NOTE 4 The term vertical, as used in the first dash
of clause 5.2 of CLC/TS 62441, does not mean a
perfectly vertical position. It should be interpreted
as any surface that can be touched by the flame of
a candle of 150 mm height and 20mm diameter
while the candle is still touching the supporting
surface. A typical candle used in the home is
assumed to be 20 mm diameter.
of clause 5.2 of CLC/TS 62441, does not mean a
perfectly vertical position. It should be interpreted
as any surface that can be touched by the flame of
a candle of 150 mm height and 20mm diameter
while the candle is still touching the supporting
surface. A typical candle used in the home is
assumed to be 20 mm diameter.
NOTE 5 It is expected that CLC/TS 62441 will in
the future be replaced by a standard, at which time
that standard will become applicable, subject to a
vote by National Committees at the time.
the future be replaced by a standard, at which time
that standard will become applicable, subject to a
vote by National Committees at the time.
Not a TV.
N/A
General
13.3.1
Delete note 4.
14
Delete note 4 and note 5.
15.1.1
Delete notes 1 and 2.
15.2
Delete note 2.
16.1
Delete note 1.
16.2
Delete the note.
20
Delete note 2.
Annex B
Replace note 1 by: In the CENELEC countries listed in IEC 62151,
special national conditions apply.
Annex G
Delete the note.
Annex J.2
Delete the notes of Table J.1.
Annex N
Add after the introduction: For ROUTINE TEST reference is made to
EN 50333. (Replaced by EN 50514)
Page 51 of 99
Report No.: 17032770 001
IEC60065K - ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
TRF No. IEC60065K
General
(A2:2010)
In IEC 60065:2001/A2
Delete
all the “country” notes according to the following list:
5.3
Note
5.4.1 Note
20
20
Note
For special national conditions, see Annex ZB.
Bibliography Additional EN standards.
ZA
Normative references to international publications
ZB
ANNEX ZB TO EN 60065, SPECIAL NATIONAL CONDITIONS (EN)
2.6.1
DK: The following is added:
Certain types of CLASS I apparatus, see 15.1.1,
may be provided with a plug not establishing
earthing continuity when inserted in Danish socket-
outlets
may be provided with a plug not establishing
earthing continuity when inserted in Danish socket-
outlets
Justification: Heavy Current Regulations, Section
107.
107.
N/A
3.Z1
(A2:2010)
Denmark
Add to the end of the subclause
Due to many existing installations where the
socket-outlets can be protected with
socket-outlets can be protected with
fuses with higher rating than the rating of the
socket-outlets the protection for
socket-outlets the protection for
pluggable equipment type A shall be an integral
part of the equipment.
part of the equipment.
Justification:
In Denmark an existing 13 A socket outlet can be
protected by a 20 A fuse.
protected by a 20 A fuse.
See EU Group differences for
this clause.
this clause.
P
Click on the first or last page to see other CINEMA 610 service manuals if exist.