Harman Kardon SOUNDSTICKS III (serv.man2) EMC - CB Certificate ▷ View online
IEC 60950-1 (ed.2)
- Page 3 of 7 -
www.nemko.com
Report No. 158002
2.7.1
Standard supply outlets protected by overcurrent
device in accordance with the NEC
device in accordance with the NEC
Class III equipment.
N/A
2.7.1
Overcurrent protection for individual transformers
that distribute power to other units over branch
circuit wiring
that distribute power to other units over branch
circuit wiring
Class III equipment.
N/A
2.7.1 Additional
requirements for overcurrent
protection apply to equipment provided with
panelboards
panelboards
Class III equipment.
N/A
2.7.1
Non-motor-operated equipment requiring special
overcurrent protective device marked with device
rating.
overcurrent protective device marked with device
rating.
Class III equipment.
N/A
2.10.5.12 Multi-layer winding wire subject to UL component
wire requirements in addition to 2.10.5.12 and
Annex U.
Annex U.
Not used.
N/A
3.1.1
Permissible combinations of internal
wiring/external cable sizes for overcurrent & short
circuit protection.
wiring/external cable sizes for overcurrent & short
circuit protection.
Class III equipment.
N/A
3.1.1
All interconnecting cables protected against
overcurrent and short circuit.
overcurrent and short circuit.
Class III equipment.
N/A
3.2
Wiring methods permit connection of equipment
to primary power supply in accordance with the
NEC
to primary power supply in accordance with the
NEC
Class III equipment.
N/A
3.2.1
Permitted use for flexible cords and plugs.
Class III equipment.
N/A
3.2.1
Flexible cords provided with attachment plug
rated 125% of equipment current rating.
rated 125% of equipment current rating.
Class III equipment.
N/A
3.2.1
Any Class II equipment provided with 15 or 20 A
standard supply outlets, Edison-base
lampholders or single pole disconnect device
provided with a polarized type attachment plug.
standard supply outlets, Edison-base
lampholders or single pole disconnect device
provided with a polarized type attachment plug.
Class III equipment.
N/A
3.2.1.2
Equipment intended for connection to DC mains
supply power systems complies with special
wiring requirements
supply power systems complies with special
wiring requirements
Class III equipment.
N/A
3.2.1.2
Equipment with one pole of the DC mains supply
connected to both the equipment mains input
terminal and the main protective earthing
terminal provided with special instructions and
construction provisions for earthing
connected to both the equipment mains input
terminal and the main protective earthing
terminal provided with special instructions and
construction provisions for earthing
Class III equipment.
N/A
3.2.1.2
Equipment with means for connecting supply to
earthing electrode conductor has no switches or
protective devices between supply connection
and earthing electrode connection.
earthing electrode conductor has no switches or
protective devices between supply connection
and earthing electrode connection.
Class III equipment.
N/A
3.2.1.2
Markings and instructions for equipment with
provisions to connect earthed conductor of a DC
supply circuit to the equipment earthing
conductor
provisions to connect earthed conductor of a DC
supply circuit to the equipment earthing
conductor
Class III equipment.
N/A
3.2.1.2
Special markings and instructions for equipment
with earthed conductor of a DC supply circuit
connected to the equipment earthing conductor
with earthed conductor of a DC supply circuit
connected to the equipment earthing conductor
Class III equipment.
N/A
3.2.1.2
Terminals and leads provided for permanent
connection of DC powered equipment to supply
marked to indicate polarity if reverse polarity may
result in a hazard.
connection of DC powered equipment to supply
marked to indicate polarity if reverse polarity may
result in a hazard.
Class III equipment.
N/A
IEC 60950-1 (ed.2)
- Page 4 of 7 -
www.nemko.com
Report No. 158002
3.2.3 Permanently
connected
equipment has provision
for connecting and securing a field wiring system
(i.e. conduit, or leads etc.) per the NEC
(i.e. conduit, or leads etc.) per the NEC
The equipment is not
permanently connected to the
mains.
permanently connected to the
mains.
N/A
3.2.3
Permanently connected equipment may have
terminals or leads not smaller than No. 18 AWG
(0.82 mm²) and not less than 150 mm in length
for connection of field installed wiring.
terminals or leads not smaller than No. 18 AWG
(0.82 mm²) and not less than 150 mm in length
for connection of field installed wiring.
The equipment is not
permanently connected to the
mains.
permanently connected to the
mains.
N/A
3.2.3
If supply wires exceed 60 °C, marking indicates
use of 75 °C or 90 °C wiring for supply
connection as appropriate.
use of 75 °C or 90 °C wiring for supply
connection as appropriate.
The equipment is not
permanently connected to the
mains.
permanently connected to the
mains.
N/A
3.2.3 Equipment
compatible
with suitable trade sizes of
conduits and cables.
The equipment is not
permanently connected to the
mains.
permanently connected to the
mains.
N/A
3.2.5
Length of power supply cord limited to between
1.5 and 4.5 m unless shorter length used when
intended for a special installation.
1.5 and 4.5 m unless shorter length used when
intended for a special installation.
Class III equipment.
N/A
3.2.5
Conductors in power supply cords sized per NEC Class III equipment.
N/A
3.2.5
Power supply cords and cord sets incorporate
flexible cords suitable for the particular
application.
flexible cords suitable for the particular
application.
Class III equipment.
N/A
3.2.6
Strain relief provided for non-detachable
interconnecting cables not supplied by a limited
power source.
interconnecting cables not supplied by a limited
power source.
Class III equipment.
N/A
3.2.9
Adequate wire bending space and volume of field
wiring compartment required to properly make
the field connections.
wiring compartment required to properly make
the field connections.
The equipment is not
permanently connected to the
mains.
permanently connected to the
mains.
N/A
3.2.9
Equipment solely for installation in Restricted
Access Locations using low voltage d.c. systems
may not need provision for connecting and
securing a field wiring system when wiring is
protected from abuse.
Access Locations using low voltage d.c. systems
may not need provision for connecting and
securing a field wiring system when wiring is
protected from abuse.
The equipment is not
permanently connected to the
mains.
permanently connected to the
mains.
N/A
3.3
Field wiring terminals provided for
interconnection of units for other then LPS or
Class 2 circuits also comply with 3.3.
interconnection of units for other then LPS or
Class 2 circuits also comply with 3.3.
Class III equipment.
N/A
3.3
Interconnection of units by LPS or Class 2
conductors may have field wiring connectors
other than specified in 3.3 if wiring is reliably
separated
conductors may have field wiring connectors
other than specified in 3.3 if wiring is reliably
separated
Class III equipment.
N/A
3.3.1
Terminals for the connection of neutral conductor
identified by a distinctive white marking or other
equally effective means
identified by a distinctive white marking or other
equally effective means
Class III equipment.
N/A
3.3.3
Wire binding screw terminal permitted for
connection of No. 10 AWG (5.3 mm²) or smaller
conductor if provided with upturned lugs, cupped
washer or equivalent retention.
connection of No. 10 AWG (5.3 mm²) or smaller
conductor if provided with upturned lugs, cupped
washer or equivalent retention.
Class III equipment.
N/A
3.3.4
Terminals accept US wire sizes (gauge)
Class III equipment.
N/A
3.3.4
Terminals accept current-carrying conductors
rated 125% of the equipment current rating.
rated 125% of the equipment current rating.
Class III equipment.
N/A
IEC 60950-1 (ed.2)
- Page 5 of 7 -
www.nemko.com
Report No. 158002
3.3.6
Field wiring terminals marked to indicate the
material(s) of the conductor for the terminals
used
material(s) of the conductor for the terminals
used
Class III equipment.
N/A
3.3.6
Aluminum conductors not permitted for
connection to terminal for equipment earthing
conductor
connection to terminal for equipment earthing
conductor
Class III equipment.
N/A
3.3.6
Field wiring connections made through the use of
suitable pressure connectors (including set screw
type), solder lugs or splices to flexible leads.
suitable pressure connectors (including set screw
type), solder lugs or splices to flexible leads.
Class III equipment.
N/A
3.4.2
Separate motor control device(s) required for
cord-connected equipment rated more than 12 A,
or with motor rated more than 1/3 hp or more
than 120 V.
cord-connected equipment rated more than 12 A,
or with motor rated more than 1/3 hp or more
than 120 V.
No such motors in the
equipment.
equipment.
N/A
3.4.8 Vertically
mounted
disconnect devices oriented
so up position of handle is "on".
No switch acting as disconnect
device
device
N/A
3.4.11
For computer-room applications, equipment with
battery systems capable of supplying 750 VA for
5 minutes provided with battery disconnect
means
battery systems capable of supplying 750 VA for
5 minutes provided with battery disconnect
means
No battery capable of supplying
750VA.
750VA.
N/A
4.2.8.1
Special opening restrictions for enclosures
around CRTs with face dimension of 160 mm or
more.
around CRTs with face dimension of 160 mm or
more.
No used CRT.
N/A
4.2.9
Compartment housing high-pressure lamp
marked to indicate risk of explosion.
marked to indicate risk of explosion.
No used.
N/A
4.2.11
For equipment mounted on racks and provided
with slide/rails allowing the equipment to slide
away from the rack for installation and
maintenance, additional construction,
performance and marking requirements are
applicable to determine the adequacy of the
slide/rails
with slide/rails allowing the equipment to slide
away from the rack for installation and
maintenance, additional construction,
performance and marking requirements are
applicable to determine the adequacy of the
slide/rails
No used
N/A
4.3.2
Loading test for equipment with handle(s) used to
support more than 9 kg
support more than 9 kg
No handle used.
N/A
4.3.6
In addition to the IEC requirements, Direct Plug-
in Equipment complies with UL 1310
in Equipment complies with UL 1310
Class III equipment.
N/A
4.3.12
The max. quantity of flammable liquid stored in
equipment per ANSI/NFPA 30 (Table NAE.6)
equipment per ANSI/NFPA 30 (Table NAE.6)
No flammable liquids within the
equipment.
equipment.
N/A
4.3.12
Equipment using replenishable liquids marked to
indicate type of liquid to be used.
indicate type of liquid to be used.
No flammable liquids within the
quipment.
quipment.
N/A
4.3.13.2 Equipment that produces x-radiation and does
not comply with 4.3.12 under all conditions of
servicing marked to indicate the presence of
radiation
servicing marked to indicate the presence of
radiation
The equipment does not produce
ionizing radiation.
ionizing radiation.
N/A
4.3.13.5 Requirements contained in the applicable
national codes apply to lasers (21 CFR 1040).
Diffusive LED only
N/A
4.7
Automated information storage equipment
intended to contain more than 0.76 m³ of
combustible media requires provision for
automatic sprinklers or a gaseous agent
extinguishing system.
intended to contain more than 0.76 m³ of
combustible media requires provision for
automatic sprinklers or a gaseous agent
extinguishing system.
The equipment has no
combustible area greater than
0.76 m³.
combustible area greater than
0.76 m³.
N/A
IEC 60950-1 (ed.2)
- Page 6 of 7 -
www.nemko.com
Report No. 158002
4.7.3.1
Equipment for use in environmental air space
other than ducts or plenums provided with metal
enclosure or with non-metallic enclosure having
adequate fire-resistance and low smoke
producing characteristics (according to UL 2043).
Equipment for installation in space used for
environmental air, described in Sec. 300-22(c) of
the NEC, provided with instructions indicating
suitability for installation
other than ducts or plenums provided with metal
enclosure or with non-metallic enclosure having
adequate fire-resistance and low smoke
producing characteristics (according to UL 2043).
Equipment for installation in space used for
environmental air, described in Sec. 300-22(c) of
the NEC, provided with instructions indicating
suitability for installation
Equipment not used in
environmental air space.
environmental air space.
N/A
4.7.3.1
Flame spread rating for external surface of
combustible material with exposed area greater
than 0.93 m² or a single dimension greater than
1.8 m; 50 or less for computer room applications
or 200 or less for other applications.
combustible material with exposed area greater
than 0.93 m² or a single dimension greater than
1.8 m; 50 or less for computer room applications
or 200 or less for other applications.
The equipment has no
combustible material greater
than 0.9m2 or single dimension
greater than 1.8m.
combustible material greater
than 0.9m2 or single dimension
greater than 1.8m.
N/A
4.7.3.4
Wire marked "VW-1" or "FT-1" considered
equivalent.
equivalent.
Considered.
P
5.1.8.2
Special earthing provisions and instructions for
equipment with high touch current due to
telecommunication network connections.
equipment with high touch current due to
telecommunication network connections.
No TNV Circuity.
N/A
5.1.8.3
Touch current due to ringing voltage for
equipment containing telecommunication network
leads.
equipment containing telecommunication network
leads.
No TNV Circuity.
N/A
5.3.7
Overloading of SELV connectors and printed
wiring board receptacles accessible to the
operator.
wiring board receptacles accessible to the
operator.
See main test report table 5.3
P
5.3.7 Tests
interrupted
by opening of a component
repeated two additional times.
See main test report table 5.3
P
5.3.9.1
Test interrupted by opening of wire or trace
subject to certain conditions.
subject to certain conditions.
Considered.
P
6
Specialized instructions for telephones that may
be connected to a telecommunications network
be connected to a telecommunications network
No TNV Circuity.
N/A
6
Marking identifying function of telecommunication
type connectors not used for connection to a
telecommunication network.
type connectors not used for connection to a
telecommunication network.
No TNV Circuity.
N/A
6.3
Equipment remotely powered over
telecommunication wiring systems provided with
specialized markings adjacent to the connection.
telecommunication wiring systems provided with
specialized markings adjacent to the connection.
No TNV Circuity.
N/A
6.3
Overcurrent protection incorporated into
equipment to provide power over
telecommunication wiring system not
interchangeable with devices of higher ratings if
operator replaceable.
equipment to provide power over
telecommunication wiring system not
interchangeable with devices of higher ratings if
operator replaceable.
No TNV Circuity.
N/A
6.4
Additional requirements for equipment connected
to a telecommunication network using cable
subject to overvoltage from power line failures
to a telecommunication network using cable
subject to overvoltage from power line failures
No TNV Circuity.
N/A
6.4
Where 26 AWG line cord required by Fig. 6C,
either the cord is provided with the equipment or
described in the safety instructions.
either the cord is provided with the equipment or
described in the safety instructions.
No TNV Circuity.
N/A
7
Equipment associated with the cable distribution
system may need to be subjected to applicable
parts of Chapter 8 of the NEC.
system may need to be subjected to applicable
parts of Chapter 8 of the NEC.
Not cable distribution systems.
N/A
H
Ionizing radiation measurements made under
single fault conditions according to 21 CFR 1020
single fault conditions according to 21 CFR 1020
The equipment does not produce
ionizing radiation
ionizing radiation
N/A
Click on the first or last page to see other SOUNDSTICKS III (serv.man2) service manuals if exist.